Industrial sugar beets to biofuel: Field to fuel production system and cost estimates

Specialized varieties of sugar beets (Beta vulgaris L.) may be an eligible feedstock for advanced biofuel designation under the USA Energy Independence and Security Act of 2007. These non-food industrial beets could double ethanol production per hectare compared to alternative feedstocks. A mixed-integer mathematical programming model was constructed to determine the breakeven price of ethanol produced from industrial beets, and to determine the optimal size and biorefinery location. The model, based on limited field data, evaluates Southern Plains beet production in a 3-year crop rotation, and beet harvest, transportation, and processing. The optimal strategy depends critically on several assumptions including a just-in-time harvest and delivery system that remains to be tested in field trials. Based on a wet beet to ethanol conversion rate of 110 dm³ Mg⁻¹ and capital cost of 128 M$ for a 152 dam³ y⁻¹ biorefinery, the estimated breakeven ethanol price was 507 $ m⁻³. The average breakeven production cost of corn (Zea mays L.) grain ethanol ranged from 430 to 552 $ m⁻³ based on average net corn feedstock cost of 254 and 396 $ m⁻³ in 2014 and 2013, respectively. The estimated net beet ethanol delivered cost of 207 $ m⁻³ was lower than the average net corn feedstock cost of 254–396$ m⁻³ in 2013 and 2014. If for a mature industry, the cost to process beets was equal to the cost to process corn, the beet breakeven ethanol price would be $387 m^-3 (587 $ m⁻³ gasoline equivalent).     

Prediction of ultrasonic wave velocity in particleboard and fiberboard

Ultrasonic wave velocities were determined at parallel and perpendicular to manufacturing direction and at the interval angles of 15° in clockwise and counterclockwise directions of particleboard and fiberboard. The experimental results were compared with the predicted values using some empirical formulae such as Hankinson and Jacoby equations. The results showed that the ultrasonic wave velocity were the highest in parallel direction in particleboard and fiberboard and decreases with increase of angle and the lowest values occurred in perpendicular direction. The predicted ultrasonic velocity using Hankinson and Jacoby equations are in close agreement with the measured values. Relationship between ultrasonic wave velocities and particles and fibers angle could be successfully presented by cubic and quadratic regression equations as well.     

Papermaking characteristics of three Populus clones grown in the north-central United States

The papermaking properties of 22 pure and hybrid poplars are being evaluated in an on-going investigation. Twenty of the poplars were harvested after 7.5 years from three different sites in the Midwestern and North Central US. The other 2 poplars survived at only two of three sites (64 total samples). The Crandon hybrid had the highest growth rate (t ha⁻¹ y⁻¹) and wood density (both averaged across the 3 sites). This poplar had a high cellulose content (compared to the average), a low lignin content and produced bleached kraft fibers at a high yield (wt.% on wood chips). Further, this poplar responded very well to kraft pulping and oxygen delignification and bleached to the highest final brightness ever observed in our laboratory (94.5% Elrepho). It also produced an 18 kappa number unbleached pulp with <0.5% rejects in only two-thirds the time required for sugar maple (Acer saccharum).We also report on clone 220-5 that had the highest area-weighted average microfibril angle. Pulps from this poplar had excellent tensile properties and further improvements are expected with 1–2 years of additional growth that should result in a small, but significant increase in average fiber length. Some results are also presented for clone 313.55 and aspen (Populus tremuloides) to demonstrate the many substantial benefits that can be accrued from proper wood selection.     

Experimental Study on Energy Consumption of Combined Conventional and Dehumidification Drying

Conventional drying, dehumidification drying, and combined conventional-dehumidification drying of wood were experimentally studied in this article. The results showed that the energy consumption in the dehumidification drying is the least but its drying time is the longest. The energy consumption in the combined drying is more than that in the dehumidification drying but less than that in the conventional drying, and the drying time is half of that in the dehumidification drying. The advantages of the combined conventional and dehumidification drying are discussed from the experiments results.     

The ability of eye-tracking metrics to classify and predict the perceived driving workload

Traffic safety is directly related to the mental and physical condition of the driver. Performing regular secondary tasks while driving is an additional activity that dissipates attention and adds to the drivers' workload. Identifying driver fatigue and workload based on gaze behavior is one way to ensure a safe driving experience. The purpose of this paper is to classify and predict driving perceived workload using a set of eye-tracking metrics (gaze fixation, duration, pointing, and pupil diameter). The ability of eye-tracking metrics to predict driving workload has been investigated. As a result, frustration, performance, and temporal load showed a correlation with gaze metrics. Gaze point, duration, fixation, and pupil diameter significantly influence driving workload.Relevance to industry: Results will supply the specialists in eye-tracking/sensor technologies and traffic safety with new knowledge to improve the design of the driving performance and safety monitoring systems and efficiency of the driving process.     

百度试验法测杨木干燥基准的初步研究

通过100℃干燥试验法的试验对2cm厚的四种杨木木材干燥特性进行了研究和分析．获得了杨木的基本干燥特性数据。同时。此法补充了观测干燥速度和扭曲的内客。较为完整和便于应用。实验结果表明，杨木属易干木材。少裂，但翘曲严重。参照百度试验缺陷等级以及干燥缺陷对应的干燥条件拟定了初步的干燥基准，在生产中可供参考使用。     

Impact of processing conditions and sizing on the thermomechanical and morphological properties of polypropylene/carbon fiber composites fabricated by material extrusion additive manufacturing

For the 3D printed composites, fiber alignment is affected by the direction of melt-flow during extrusion of filaments and subsequently through the printing nozzle. The resulting fibers orientation and the fiber-matrix compatibility have a direct correlation with mechanical properties. This study investigates the impact of processing conditions on the state of the carbon fiber types and their orientation on the mechanical properties of 3D-printed composites. Short and long carbon fibers were used as starting reinforcing materials, and the state of fibers at the beginning and on the printed parts were evaluated. Strong anisotropy in terms of mechanical properties (flexural and impact properties) was observed for the samples printed with different printing orientations. Interestingly, the number of voids in the printed composites was found to be correlated with the fiber types. The present work provides a step towards the optimization of tailored composite properties by additive manufacturing.     

Intelligent adaptive process control using dynamic deadband for semiconductor manufacturing

This paper proposes an efficient control method to minimize process error and to reduce process variance in semiconductor manufacturing. The photolithography (photo) process forms a complex semiconductor circuit and is important for quality. Obstacles to the process include the facility itself, vibration, wear and tear, product/process changes and environmental influences. Control methodologies being currently used to address these issues often amplify the variation of the process by failing to perform adequate process control. Therefore, this paper proposes an effective process control method to reduce process variance by quickly detecting and identifying process disturbances and accurately reflecting the degree of change to process control. This study proposes dynamic deadband control that uses a region (band) to detect the status of a process change. It adjusts the process control based on the changes detected. In this research, the semiconductor manufacturing company is supported to perform control that is more precise and reduces fluctuations by producing products of uniform quality. In addition, it can contribute to yield due to the quality incentive and increased process control of semiconductor manufacturing.     

High-temperature superconducting microwave devices: Fundamental issues in materials, physics, and engineering

High-T _c superconductivity has generated a great deal of interest because of the challenges it presents in the fields of material science, condensed matter physics, and electrical engineering, and because of the potential applications which may result from these research efforts. Thin-film passive microwave components may become the first high-temperature superconducting (HTS) devices available for widespread use and commercialization. In this article, we review aspects of material science, physics, and engineering which directly impact high-T _c superconducting microwave devices and discuss issues which determine the performance of these devices. Methods of growing HTS thin films on large-area substrates, techniques for fabricating single-level HTS passive microwave components, and the relevant properties of high-T _c superconducting films are discussed, with a focus on thin films of the HTS material YBa₂Cu₃O_7–. Several known mechanisms for microwave loss in both the superconductor and the dielectric substrate are presented. An overview of the general classes of superconducting passive microwave devices is given, and representative microwave devices which have been recently demonstrated are described in detail. Examples of a select few HTS active microwave components are also presented. Potential microwave applications are illustrated with comparisons to current technology.