The effect of particle size distribution on the microstructure and properties of Al2O3 ceramics formed by stereolithography

Stereolithography (SL) shows advantages for preparing alumina-based ceramics with complex structures. The effects of the particle size distribution, which strongly influence the sintering properties in ceramic SL, have not been systematically explored until now. Herein, the influence of the particle size distribution on SL-manufactured alumina ceramics was investigated, including bending strength at room temperature, post-sintering shrinkage, porosity, and microstructural morphology. Seven particle size distributions of alumina ceramics were studied (in μm/μm: 30/5, 20/3, 10/2, 5/2, 5/0.8, 3/0.5, and 2/0.3); a coarse:fine particle ratio of 6:4 was maintained. At the same sintering temperature, the degree of sintering was greater for finer particle sizes. The particle size distribution had a larger influence on flexural strength, porosity and shrinkage than sintering temperature when the particle size distribution difference reached 10-fold but was weaker for 10 μm/2 μm, 5 μm/2 μm and 5 μm/0.8 μm. The sintering shrinkage characteristics of cuboid samples with different particle sizes were studied. The use of coarse particles influenced the accuracy of small-scale samples. When the particle size was comparable to the sample width, such as 30 μm/5 μm and 5 mm, the width shrinkage was consistent with the height shrinkage. When the particle size was much smaller than the sample width, such as 2 μm/0.3 μm and 5 mm, the width shrinkage was consistent with the length shrinkage. The results of this study provide meaningful guidance for future research on applications of SL and precise control of alumina ceramics through particle gradation.     

Irradiation-induced large bubble formation and grain growth in super nano-grained ceramic

In this work, 0.5TRPO•0.5Gd₂Zr₂O₇ ceramic with an average grain size of only ∼15 nm was prepared by a high pressure (5 GPa/520 °C) sintering method. Phase evolutions and microstructure changes of the as-fabricated super nano and micron-grained ceramics under a high-dose displacement damage induced by 300 keV Kr²⁺ ions were investigated. The results show that the super nano-grained ceramic has low degree of amorphization, obvious grain growth (2–3 times in grain size) and big Kr bubbles (10–68 nm) formation after irradiation. The micron-grained ceramic was severely amorphized after irradiation and many microcracks were formed parallel to its surface. The formation mechanism of Kr bubbles in the super nano-grained ceramic is on account of grain boundary diffusion and migration induced by the accumulation of the injecting Kr ions and irradiation defects. Nevertheless, microcracks formed in the micron-grained sample are caused by the accumulation of Kr atoms.     

Remarkably enhanced energy storage properties of lead-free Ba0.53Sr0.47TiO3 thin films capacitors by optimizing bottom electrode thickness

The lead-free Ba_0.53Sr_0.47TiO₃ (BST) thin films buffered with La_0.67Sr_0.33MnO₃ (LSMO) bottom electrode of different thicknesses were fabricated by pulsed laser deposition method on a (001) SrTiO₃ substrate. It was found that the roughness of electrode decreases and substrate stress relaxes gradually with the increase of LSMO thickness, which is beneficial for weakening local high electric field and achieving higher E_b. Therefore, the recoverable energy density (W_rec) of BST films can be greatly improved up to 67.3 %, that is, from 30.6 J/cm³ for the LSMO thickness of 30 nm up to 51.2 J/cm³ for the LSMO thickness of 140 nm after optimizing the LSMO thickness. Furthermore, the thin film capacitor with a 140 nm LSMO bottom electrode shows an outstanding thermal stability from 20 °C to 160 °C and superior fatigue resistance after 10⁸ electrical cycles with only a slightly decrease of W_rec below 1.6 % and 3.7 %, respectively. Our work demonstrates that optimizing bottom electrodes thickness is a promising way for enhancing energy storage properties of thin-film capacitors.     

综合运维软件在供水企业中的应用

文章简述了IT运维的发展趋势,举例说明了综合运维软件的功能特点,并阐述了综合运维软件在供水企业中的应用案例及应用效果,由此提出综合运维软件的重要作用。     

A zirconium-free glaze system for sanitary ceramics with SiO2-CaCO3-TiO2 composite opacifier containing anatase: Effect of interface combination among SiO2, CaCO3 and TiO2

TiO₂ is an ideal substitute to ZrSiO₄ ceramic opacifier, yet it is limited to application because of the undesirable yellowing resulting from rutile formation. Herein, the SiO₂-CaCO₃-TiO₂ composite opacifier (Si-Ca-Ti) was constructed. The glaze used Si-Ca-Ti presents a superior opacification performance than ZrSiO₄ opacified glaze without causing yellowing, showing L*, a*, b* values of 94.81, -0.67 and 3.23. By comparison, the glaze using SiO₂, CaCO₃, and TiO₂ mixture shows lower opacification and yellowish surface with L* and b* values of 92.99 and 5.36. It is revealed that there is a close interface bonding among SiO₂, CaCO₃ and TiO₂ in Si-Ca-Ti, which promotes their combination reaction to generate opacification phase titanite and inhibit rutile formation when sintering, resulting in the white surface and opacification improvement of the glaze. This study proposes a green and efficient strategy to achieve white and highly opacified glaze for sanitary ceramics, exhibiting good application prospect.     

基于MF-R和AWS密钥管理机制的物联网健康监测大数据分析系统

带有传感器的可穿戴式医疗设备不断生成大量数据，由于数据的复杂性，难以通过处理和分析大数据来找到有价值的决策信息。为了解决这个问题，提出了一种新的物联网体系结构，用于存储和处理医疗应用的可扩展传感器数据（大数据）。所提出的架构主要由两个子架构组成：Meta Fog重定向（MF-R）架构和AWS密钥管理机制。MF-R架构使用Apache Pig和Apache HBase等大数据技术来收集和存储不同传感器设备生成的传感器数据，并利用卡尔曼滤波消除噪声。AWS密钥管理机制使用密钥管理方案，目的是保护云中的数据，防止未经授权的访问。当数据存储在云中时，所提出的系统能够使用随机梯度下降算法和逻辑回归来开发心脏病的预测模型。仿真实验表明，和其他几种算法相比，提出的算法具有更小的误差，且在吞吐量、准确度等方面具有一定的优越性。     

喉及下咽部CT仿真内窥镜成像技术分析及其临床研究

目的:探索CT仿真内窥镜成像技术在对喉及下咽部检查的临床价值。方法:对20例正常健康人群和20例喉及咽部经病理证实病变的患者行CT仿真内窥镜(3.0mm层厚、1.0mm间隔、1.0螺距)成像检查,并与手术结果进行对比分析。结果:CT仿真内窥镜成像技术对喉及下咽部病变的检查准确率约为90.0%,与临床病理组织检查相比Χ2=1.0000,P0.05,差异具有统计学意义。结论 :CT仿真内窥镜对喉及下咽部疾病患者的成像处理,可对异常及正常的喉部及下咽部情况进行反馈,属于非侵袭性的、新型的检查方式,具有广阔的临床运用前景。     

咖啡渣活性炭的制备、表征及其对Cr(Ⅵ)的吸附机制研究

以碘吸附值为评价指标，活化时间、活化温度和浸渍比为影响因素，采用响应面法试验设计对磷酸活化法制备咖啡渣活性炭的工艺条件进行优化，并通过静态吸附试验研究了不同吸附时间、溶液pH值和吸附温度条件下，活性炭对水溶液中Cr（Ⅵ）吸附性能的影响，最后利用Langmuir、Freundlich吸附等温方程、准一级动力学方程、准二级动力学方程和颗粒内部扩散方程进行拟合。试验结果表明，制备咖啡渣活性炭的最佳工艺条件为活化时间1 h、活化温度498℃、浸渍比1.72；在此条件下活性炭得率为30.4%，碘吸附值为（799±16）mg/g，比表面积为1 006 m²/g，孔容为0.779 cm³/g、微孔孔容为0.051 cm³/g、平均孔径为3.088 nm。较低pH值和较高温度能够促进活性炭对Cr（Ⅵ）的吸附；Langmuir等温方程能够更好地描述活性炭对Cr（Ⅵ）的吸附效果；活性炭对Cr（Ⅵ）的吸附分3个阶段：快速吸附阶段、慢速吸附阶段和吸附平衡阶段，10 min内可完成吸附总量的79%，360 min内达到吸附平衡，该吸附过程符合准二级吸附动力学方程。分析表明咖啡渣活性炭对Cr（Ⅵ）的吸附主要为单分子层的化学吸附。     

析湿工况下翅片管式换热器表面粉尘沉积过程的数值模型

空调器采用翅片管式换热器作为蒸发器，在制冷工况下换热器表面发生析湿及粉尘沉积，导致性能衰减。建立湿翅片表面粉尘颗粒物沉积过程的数学模型，模拟冷凝水捕集颗粒物以及湿积灰层黏附颗粒物的过程。被冷凝水捕集的颗粒物数量等于运动轨迹与水表面轮廓会出现相交的入射颗粒物的数量；后续的入射颗粒物与湿积灰层碰撞时，部分入射颗粒物会发生沉积且部分被碰撞的已沉积湿颗粒物会发生移除，这两部分的颗粒物数量相减即为被湿积灰层黏附的颗粒物数量。模拟与实验结果的对比表明，预测的湿积灰层形状与实验照片的吻合度较好，预测的单位面积颗粒物沉积质量与91%的实验数据之间的误差在±20%之间，平均误差为11.8%。     

彩横条纬编织物的生产

在普通圆纬机上编织彩横条织物时，彩横务循环单元受到一定限制。而在具有四色或六色调线装置的横务纹机上编织彩横条织物时，可扩大彩横条循环单元的横列数。文中举列说明了彩横条织物的设计与上机工艺的制定方法。