Recent advances in electrocatalysts for seawater splitting in hydrogen evolution reaction

Electrocatalytic water splitting is an important method to produce green and renewable hydrogen (H₂). One of the hindrances for wide applications of electrocatalysis in H₂ production is the lack of freshwater resources. Comparatively, seawater splitting has become an effective approach for large-scale H₂ production due to its abundant reserves. However, the increased complexity of seawater content emerged more problems in electrocatalytic seawater splitting. Recently, various strategies have been reported on improving the performance of electrocatalysts applied in seawater. Herein, this review firstly analyzed the mechanisms and challenges of electrocatalytic seawater splitting to evolve H₂, and summarized the recent progress on H₂ production in electrocatalytic seawater splitting. Furthermore, suggestions for future work have been provided for guidance.     

Design of Ti4+-doped Li3V2(PO4)3/C fibers for lithium energy storage

In this work, we propose a facile approach to fabricate Ti⁴⁺-doped Li₃V₂(PO₄)₃/C (abbreviated as C-LVTP) nanofibers using an electrospinning route followed by a high temperature treatment. In this designed nanocomposite, the ultrafine LVTP dots are homogeneously dispersed into one-dimensional carbon nanofibers and the Ti⁴⁺ doping does not destroy the crystal structure of monoclinic Li₃V₂(PO₄)₃. Compared to the undoped Li₃V₂(PO₄)₃/C (abbreviated as C-LVP), the as-fabricated C-LVTP fibers present higher reversible capacity, superior high-rate capability as well as better cyclic property. Especially, the C-LVT_7%P cathode delivers not only high capacities of 187.2 and 160.3 mAh g^?1 at 0.5 and 10 C respectively, but also stable cyclic property with the reversible capacity of 135.8 mAh g^?1 at 20 C following 500-cycle spans. The good battery characteristics of C-LVT_7%P can be mainly ascribed to Ti⁴⁺ doping, which can increase the electrical conductivity and Li⁺ diffusion coefficient.     

金针菇多糖对微冻大黄鱼及其鱼片品质变化的影响

为研究金针菇多糖（polysaccharide from Flammulina velutipes，FVP）对微冻大黄鱼及鱼片在贮藏期间肌原纤维蛋白性质的变化及水分分布的影响，实验分别选用0.03、0.06、0.09 g/L FVP浸渍处理大黄鱼和鱼片，以无菌水处理为对照组，分析微冻贮藏期间样品的感官指标得分、总挥发性盐基氮含量、总巯基含量、Ca2＋-ATPase活性、蛋白流变学性质以及水分迁移变化规律。结果表明：FVP可有效抑制整鱼总挥发性盐基氮含量上升和感官得分的下降；减缓整鱼及鱼片在微冻过程中总巯基含量、Ca2＋-ATPase活性下降和水分流失；此外FVP还能够延缓大黄鱼因腐败而出现的蛋白凝胶能力减弱。在本实验选取的多糖浓度范围内，0.09 g/L FVP处理组保鲜效果较强。该研究结果可为FVP用于水产品贮运保鲜提供理论参考。     

Preparation and Evaluation of a Self-Nanoemulsifying Drug Delivery System Loaded with Heparin Phospholipid Complex

A self-nanoemulsifying drug delivery system (SNEDDS) was developed to enhance the absorption of heparin after oral administration, in which heparin was compounded with phospholipids to achieve better fat solubility in the form of heparin-phospholipid (HEP-Pc) complex. HEP-Pc complex was prepared using the solvent evaporation method, which increased the solubility of heparin in n-octanol. The successful preparation of HEP-Pc complex was confirmed by differential scanning calorimetry (DSC), Fourier-transform infrared (FT-IR) spectroscopy, NMR, and SEM. A heparin lipid microemulsion (HEP-LM) was prepared by high-pressure homogenization and characterized. HEP-LM can enhance the absorption of heparin after oral administration, significantly prolong activated partial thromboplastin time (APTT) and thrombin time (TT) in mice, and reduce fibrinogen (FIB) content. All these outcomes indicate that HEP-LM has great potential as an oral heparin formulation.     

High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.     

In2O3:Ga and In2O3:P-based one-electrode gas sensors: Comparative study

Gas sensing characteristics of one-electrode sensors based on the In₂O₃ ceramics doped by gallium and phosphorus have been discussed. In₂O₃-based ceramic was prepared by sol–gel technology. Ozone, CO, CH₄ and H₂ were used as tested gases. The doping concentration effect on the sensor parameters such as magnitude of response, operating temperature, response and recovery times, sensitivity to the air humidity, and selectivity have been analyzed. It was shown that In₂O₃ doping by Ga and P could be used for the sensor performance optimization. It was assumed that the appearance of the second phase (InPO₄ and Ga₂O₃) and the change of structural parameters, taking place during doping process, were the main factors controlling the change of operating characteristics in In₂O₃:P and In₂O₃:Ga-based sensors.     

Spray coating process variable and property analysis of UV-curable polyurethane acrylate coating on polycarbonate substrate

A series of spray coating experiments were conducted on an UV-curable, polyurethane-modified, acrylate-based coating formulation with the aim to control defects, coating thickness, and thickness variation. Statistical approaches including design of experiment, residual examination, analysis of variance, and t-test were used in designing the experiments and analyzing data. Viscosity of formulation, atomizing pressure, liquid feeding pressure, distance between nozzle and substrate, and travel speed of substrate were the process variables studied. The ranges of process variables that gave defect-free coating were identified and used in the subsequent experiments to determine process variables and interactions that had significant contribution to the changes in coating thickness and thickness variation. All process variables studied were found to have contribution to the change in coating thickness, but they showed no significant contribution to the variation of coating thickness. No interaction displayed significant contribution. Confirmation tests performed on extra samples prepared with varying coating thicknesses indicated a good agreement with the experimental results. Additional samples were tested for total transmittance, transmission haze, adhesion, surface roughness, hardness, scratch hardness, abrasion resistance, and durability to attack of car wash chemicals. Spray coated samples showed slight improvement in the total transmittance over the uncoated samples, while maintaining the transmission haze and exhibiting rougher surfaces. Only samples with thin coatings were found to possess sufficient adhesion to the substrate. These thin coatings gave improved hardness, scratch hardness, and durability to car wash attack to the level comparable to commercial coated polycarbonate headlamp lenses, whilst giving better abrasion resistance.