Fabrication of barium titanate ceramics via digital light processing 3D printing by using high refractive index monomer

A digital light processing (DLP) technology has been developed for 3D printing lead-free barium titanate (BTO) piezoelectric ceramics. By comparing the curing and rheological properties of slurries with different photosensitive monomer, a high refractive index monomer acryloyl morpholine (ACMO) was chosen, and a design and preparation method of BTO slurry with high solid content, low viscosity and high curing ability was proposed. By further selecting the printing parameters, the single-layer exposure time was reduced and the forming efficiency has been greatly improved. Sintered specimens were obtained after a nitrogen-air double-step debinding and furnace sintering process, and the BTO ceramics fabricated with 80 wt% slurry shows the highest relative density (95.32 %) and piezoelectric constant (168.1 pC/N). Furthermore, complex-structured BTO ceramics were prepared, impregnated by epoxy resin and finally assembly made into hydrophones, which has significance for the future design and manufacture of piezoelectric ceramic-based composites that used in functional devices.     

Preparation of high-purity SiC ceramics with good plasma corrosion resistance by hot-pressing sintering

High-purity SiC ceramic devices are applied in semiconductor industry owing to their outstanding properties. Nevertheless, it is difficult to densify SiC ceramics without any sintering additive even by HP sintering. In this work, high-purity and dense SiC ceramics were fabricated by HP sintering with very low amounts of sintering aids. Residual B content was only 556 ppm and relative density was more than 99.5%. Furthermore, thermal conductivity of as-prepared SiC ceramics was improved from 155 W m^?1 K^?1 to 167 W m^?1 K^?1 by increasing holding time and their plasma corrosion resistance was promoted in the meantime. The as-prepared high-purity SiC ceramics have broad application prospects in the field of semiconductor industry.     

Symmetric and asymmetric membranes based on La0.5Sr0.5Fe0.7Ga0.3O3-δ perovskite with high oxygen semipermeation flux performances and identification of the rate-determining step of oxygen transport

This work focuses on identifying the rate-determining step of oxygen transport through La_0.5Sr_0.5Fe_0.7Ga_0.3O_3-δ membranes with symmetric and asymmetric architectures. The best oxygen semipermeation fluxes are 3.4 10⁻³ mol. m^-2.s^-1 and 6.3 10⁻³ mol. m^-2.s^-1 at 900 °C for the symmetric membrane and asymmetric membrane with a modified surface. The asymmetric membrane with a modified surface leads to an increase of approximately 7 times the oxygen flux compared to that obtained with the La_0.5Sr_0.5Fe_0.7Ga_0.3O_3-δ dense membrane without surface modification. This work also shows that the oxygen flux is mainly governed by gaseous oxygen diffusion through the porous support of asymmetric La_0.5Sr_0.5Fe_0.7Ga_0.3O_3-δ membranes.     

An improved feedrate scheduling method for NURBS interpolation in five-axis machining

Five-axis machining plays an important role in manufacturing by dint of its high efficiency and accuracy. While two rotation axes benefit the flexibility of machining, it also brings limitations and challenges. In order to further balance machining precision and efficiency, an improved feedrate scheduling method is presented considering geometric error and kinematic constraints for the Non Uniform Rational B-Spline (NURBS) interpolation in five-axis machining. A simplification method is proposed to calculate the geometric error which describes the deviation between the ideal tool path and the real tool path induced by the non-linear movement. A linear relation between geometric error and feedrate is built to limit the feedrate. The constraints determined by single axis kinematic performance and tangential kinematic performance are also considered. Under these constraints, a constrained feedrate profile is determined. Aiming to get more constant feedrate in the difficult-to-machine areas, this work proposes a scheduling method which combines morphological filtering and S-shape acceleration/deceleration (acc/dec) mode. Simulations and experiments are performed to compare the proposed feedrate scheduling method with two previous feedrate scheduling method and the results prove that the proposed feedrate scheduling method is reliable and effective.     

Self-assembled cubic-hexagonal perovskite nanocomposite as intermediate-temperature solid oxide fuel cell cathode

Self-assembly is an emerging strategy for preparing composite cathodes with good oxygen electrochemical reduction activity and congenital chemical compatibility for intermediate-temperature solid oxide fuel cell (IT-SOFC). Here we report that a self-assembled BaCo_0.6Zr_0.4O_3-δ (BZC-BC) nanocomposite is prepared through one-pot glycine-nitrate process and exhibits high cathode performance. The BZC-BC nanocomposite is composed of 62 mol% cubic perovskite BaZr_0.82Co_0.18O_3-δ (BZC) as an ionic conductor and 38 mol% hexagonal perovskite BaCo_0.96Zr_0.04O_2.6+δ (12H-BC) as a mixed ionic and electronic conductor. The BZC-BC nanocomposite has the pomegranate-like particles aggregated with a larger number of nanoparticles (50-100 nm) which greatly enlarge the three-phase boundary sites. The BZC-BC nanocomposite exhibits a thermal expansion coefficient of 12.89 × 10⁻⁶ K⁻¹ well-matched with that of Ce_0.8Gd_0.2O_3-δ (12.84 × 10⁻⁶ K⁻¹) electrolyte. The high electro-catalytic activity of BZC-BC nanocomposite cathode for oxygen reduction is reflected by the low polarization resistances of oxygen ions incorporation at cathode/electrolyte interface (0.02823 Ω cm²), oxygen species diffusion (0.03702 Ω cm²) and oxygen adsorptive dissociation (0.07609 Ω cm²) at 700 °C. The single cell with BZC-BC nanocomposite cathode achieves the maximum power density of 1094 mW cm⁻² at 650 °C and shows good stability under 25 h run.     

中国智能机械制造评价及发展研究

以中国规模以上工业企业数据库为基础，结合在智能制造主要区域调研的结果，筛选出15145家智能制造企业，经同行评议后，生成322家候选企业名单；再由资深产业专家从“开发式创新”和“探索式创新”两个方面去考察候选企业的能力，得到中国智能制造百强排行榜；随后根据行业分类，得到智能机械制造企业排行榜。在概述了智能机械制造上榜企业的基本情况后，着重分析了前20强企业，并提出了中国智能机械制造发展路径和未来的发展趋势。     

Fretting-induced friction and wear in large flat-on-flat contact with quenched and tempered steel

Fretting may cause severe surface damage and lead to unexpected fatigue failure. Our test apparatus was designed based on reciprocating, large, annular flat-on-flat contact without any edge effects in the direction of the fretting movement. Fretting wear tests were run with quenched and tempered steel with different normal pressures and sliding amplitudes under gross sliding conditions. The development of the friction coefficient and total wear mass depended mostly on the accumulated sliding distance. Initially, friction and wear were highly adhesive but gradually changed to abrasive due to third body accumulation in the interface.     

A novel fast distance relay for series compensated transmission lines

This paper presents a fast distance relay for series compensated transmission lines based on the R–L differential-equation algorithm using the theory of equal transfer process of transmission lines. The measuring distances based on the proposed algorithm can fast approach the actual value of fault distance when a fault occurs in front of the series capacitor. When a fault occurs behind of the series capacitor, the fault loop, including the series capacitor, does not match the R–L transmission line model, so the measuring distances fluctuate severely. Based on this, the relative position of the fault with respect to the series capacitor can be judged effectively according to the fluctuation range of the measuring distances, and the accurate fault location can be obtained fast. A variety of PSCAD/EMTDC simulation tests show that the new relay has fast operating speed and high accuracy when applied to the long series compensated transmission lines.     

等时格架下陆相页岩多尺度岩相精细识别及控制因素分析——以渤海湾盆地东营凹陷为例

由于陆相页岩控制因素的多样性与复杂性，使得页岩岩相的精细识别及预测具有一定的难度，同时，页岩岩相发育的控制因素也一直没有明确。通过近年来对渤海湾盆地东营凹陷泥页岩岩相及控制因素的持续研究，总结了不同级次等时地层格架下陆相页岩岩相多尺度精细识别标志与发育特征，提出了2种尺度的控制因素。岩相可分为层耦、层耦组、岩相域和岩相层序4个尺度，其中层耦受古生产力、季风、氧化—还原条件联合控制，层耦组—岩相域—岩相层序受物源、气候、构造联合控制，多种因素叠合造就了陆相页岩岩相的复杂性与多样性。研究成果对于系统刻画中国陆相页岩岩相特征、深入理解不同尺度岩相形成机理具有重要意义。      

Electrochemical generation of hydrogenated graphene flakes

A cathodic electrochemical method for the exfoliation of graphite to produce hydrogenated graphenic flakes is introduced. The resulting solutions consist of micrometer-sized and predominantly 1–4 layers thick hydrogenated graphenic flakes. In contrast to oxygenation, chemisorption of hydrogen avoids the formation of structural vacancy defects in the exfoliated flakes. Thermal desorption of hydrogen therefore results in graphenic flakes with a low defect density and consequently good electrical conductivity. Cathodic electrochemical exfoliation offers a remarkably simple and effective technique for the production of high quality graphene flakes and their hydrogenated relatives.