15000 m^3／h制氧机组同步电动机起动技术研究

介绍液态软起动技术在济钢 15000 m3/h制氧机配套的 6000 kW同步电动机上的应用情况,阐述了系统的原理、特点、仿真计算及实际应用后达到的效果.     

In‐Situ Observation of the Formation of MnS during Solidification of High Sulphur Steels

A Confocal Scanning Laser Microscope equipped with a gold image furnace was used to directly observe the precipitation of MnS during solidification of high sulphur steels under isothermal conditions in the temperature region 1440 to 1480°C on the free surface of the steel melt. For the case of Al‐killed steels, below 1480°C MnS particles were found to precipitate with Fe forming simultaneously around them. This MnS containing structure continued to grow rapidly (264 μm/s) as a surface film. The film gradually changed, as the level of S in the melt decreased, into a eutectic structure (with lamella spacing of 2 μm) as predicted by thermodynamics. In Si‐ killed steels there was significantly lower tendency to form MnS both in terms of time until precipitation occurred and growth rate.     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

250W带功率因数校正整流电源模块的研制

功率因数校正技术越来越成为电源行业研究的热点。文中介绍了适用于雷达等设备的250W带功率因数校正整流电源模块的设计，分析了其中升压电感器设计、主开关管保护、控制电路消振、散热设计和表面贴装等关键技术，完成了实验研究，获得了满意的试验结果。     

Ability of a contactless inductive device for the characterization of the critical current versus temperature in superconducting rings at temperatures close to TC

Critical current measurements for three polycrystalline rings of YBCO, three Bi-2223, and one YBCO + Ag were developed from a temperature close to 80 K to the critical temperature using a previously reported contactless inductive device based on the transformer method. These data were used to analyze the ability of this device to characterize, in superconducting rings, the Ginzburg-Landau, Ambegaokar-Baratoff, and De Gennes regimes as well as the crossover temperature between them.     

Investigation on vapor-cooled current leads operating in a pulse mode

This paper describes transient numerical modeling for thermal characteristic of vapor-cooled current leads under pulse operation. The transient thermal analysis considers the temperature difference between a helium gas flow and a copper lead with temperature dependent properties of helium gas, copper and stainless steel. The numerical analysis was validated by an experiment with commercially available 100 A vapor-cooled current leads. A proper overloading factor calculation and the effect of intermediate cooling are presented for the current leads under pulse operation, which can significantly reduce heat input to a cryostat.     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

改进异步电机直接转矩控制系统的仿真研究

本文介绍了直接转矩控制系统的控制原理,并针对基于直接转矩控制的异步电动机运行时存在较大的电流及转矩脉动问题,提出一种新的控制方案,并基于Matlab 6.5对这种新方法进行仿真,仿真结果表明该方案能有效的解决电流及转矩脉动的问题.     

就地补偿在动力厂水泵电机上的应用实例

就我公司动力厂给水车间155kW水泵电机无功就地补偿的可行性及经济效益进行了分析和研究，对工厂用电如何节能降耗有一定的参考价值。     

高炉富氧鼓风的现状及机前供氧

阐述了高炉生产采用富氧大喷煤的必要性，国内高炉富氧鼓风的现状，以及机前富氧的优点和应采取的安全措施。