Effects of SiC content on the densification,microstructure, and mechanical properties of HfB2–SiC composites

To investigate the effects of SiC on microstructure, hardness, and fracture toughness, 0, 10, 20, and 30 vol% SiC were added to HfB₂ and sintered by SPS. Upon adding SiC to 30 vol%, relative density increased about 4%; but HfB₂ grain growth had a minimum at 20 vol% SiC. This may be due to grain boundary silicate glass, responsible for surface oxide wash out, enriched in SiO₂ with higher fraction of SiC. By SiO₂ enrichment, the glass viscosity increased and higher HfO₂ remained unsolved which subsequently lead to higher grain growth. Hardness has increased from about 13 to 15 GPa by SiC introduction with no sensible variation with SiC increase. Residual stress measurements by Rietveld method indicated high levels of tensile residual stresses in the HfB₂ Matrix. Despite the peak residual stress value at 20 vol% SiC, fracture toughness of this sample was the highest (6.43 MPa m^0.5) which implied that fracture toughness is mainly a grain size function. Tracking crack trajectory showed a mainly trans-granular fracture, but grain boundaries imposed a partial deflection on the crack pathway. SiC had a higher percentage in fracture surface images than the cross-section which implied a weak crack deflection.     

Effects of structural characteristics on microwave dielectric properties of low-loss (Zn1-xNix)ZrNbTaO8 ceramics

Low-loss (Zn_1-xNi_x)ZrNbTaO₈ (0.02?≤?x?≤?0.10) ceramics possessing single wolframite structure are initiatively synthesized by solid-state route. Based on the results of Rietveld refinement, complex chemical bond theory is used to establish the correlation between structural characteristics and microwave performance in this ceramic system. A small amount of Ni²⁺ (x?=?0.06) in A-site with the fixed substitution of Ta⁵⁺ in B-site can effectually raise the Q?×?f value of ZnZrNb₂O₈ ceramic, embodying a dense microstructure and high lattice energy. The dielectric constant and τ_f are mainly affected by bond ionicity and the average octahedral distortion. The (Zn_0.94Ni_0.06)ZrNbTaO₈ ceramic sample sintered at 1150?°C for 3?h exhibits an outstanding combination of microwave dielectric properties: ε_r =?27.88, Q?×?f?=?128,951?GHz, τ_f =?–39.9?ppm/°C. Thus, it is considered to be a candidate material for the communication device applications at high frequency.     

Design structure matrix (DSM) method application to issue of modeling and analyzing the fault tree of a wind energy asset

The perpetual energy production of a wind farm could be accomplished (under proper weather conditions) if no failures occurred. But even the best possible design, manufacturing, and maintenance of a system cannot eliminate the failure possibility. In order to understand and minimize the system failures, the most crucial components of the wind turbines, which are prone to failures, should be identified. Moreover, it is essential to determine and classify the criticality of the system failures according to the impact of these failure events on wind turbine safety. The present study is processing the failure data from a wind farm and uses the Fault Tree Analysis as a baseline for applying the Design Structure Matrix technique to reveal the failure and risk interactions between wind turbine subsystems. Based on the analysis performed and by introducing new importance measures, the “readiness to fail” of a subsystem in conjunction with the “failure riskiness” can determine the “failure criticality.” The value of the failure criticality can define the frame within which interventions could be done. The arising interventions could be applied either to the whole system or could be focused in specified pairs of wind turbine subsystems. In conclusion, the method analyzed in the present research can be effectively applied by the wind turbine manufacturers and the wind farm operators as an operation framework, which can lead to a limited (as possible) design‐out maintenance cost, failures' minimization, and safety maximization for the whole wind turbine system.     

A design of a robust discrete-time controller

In this paper, we proposed a robust discrete-time controller. This control system, which is derived from the idea of the normalized plant, does not include plant parameters. Thus, we obtain a control system independent of plant parameters and that has the same structure as a conventional optimal servo control system. Simulation and experimental results show that the proposed method is fairly robust to plant parameter variations and external disturbances.     

Application of Vis–NIR hyperspectral imaging in classification between fresh and frozen-thawed pork Longissimus Dorsi muscles

Fresh and frozen-thawed (F-T) pork meats were classified by Vis–NIR hyperspectral imaging. Eight optimal wavelengths (624, 673, 460, 588, 583, 448, 552 and 609 nm) were selected by successive projections algorithm (SPA). The first three principal components (PCs) obtained by principal component analysis (PCA) accounted for over 99.98% of variance. Gray-level-gradient co-occurrence matrix (GLGCM) was applied to extract 45 textural features from the PC images. The correct classification rate (CCR) was employed to evaluate the performance of the partial least squares-discriminate analysis (PLS-DA) models, by using (A) the reflected spectra at full wavelengths and (B) those at the optimal wavelengths, (C) the extracted textures based on the PC images, and (D) the fused variables combining spectra at the optimal wavelengths and textures. The results showed that the best CCR of 97.73% was achieved by applying (D), confirming the high potential of textures for fresh and F-T meat discrimination.     

Static stress analysis of carbon nano-tube reinforced composite (CNTRC) cylinder under non-axisymmetric thermo-mechanical loads and uniform electro-magnetic fields

Static stresses analysis of carbon nano-tube reinforced composite (CNTRC) cylinder made of poly-vinylidene fluoride (PVDF) is investigated in this study. Non-axisymmetric thermo-mechanical loads are applied on cylinder in presence of uniform longitudinal magnetic field and radial electric field. The surrounded elastic medium is modeled by Pasternak foundation because of its advantages to the Winkler type. Distribution of radial, circumferential and effective stresses, temperature field and electric displacements in CNTRC cylinder are determined based on Mori–Tanaka theory. The detailed parametric study is conducted, focusing on the remarkable effects of magnetic field intensity, elastic medium, angle orientation and volume fraction of carbon nano-tubes (CNTs) on distribution of effective stress. Results demonstrated that fatigue life of CNTRC cylinder will be significantly dependent on magnetic intensity, angle orientation and volume fraction of CNTs. Results of this research can be used for optimum design of thick-walled cylinders under multi-physical fields.     

Dissociating uncertainty responses and reinforcement signals in the comparative study of uncertainty monitoring.

Although researchers are exploring animals' capacity for monitoring their states of uncertainty, the use of some paradigms allows the criticism that animals map avoidance responses to error-causing stimuli not because of uncertainty monitored but because of feedback signals and stimulus aversion. The authors addressed this criticism with an uncertainty-monitoring task in which participants completed blocks of trials with feedback deferred so that they could not associate reinforcement signals to particular stimuli or stimulus-response pairs. Humans and 1 of 2 monkeys were able to make cognitive, decisional uncertainty responses that were independent of feedback or reinforcement history within a task. This finding unifies the comparative literature on uncertainty monitoring. The dissociation of performance from reinforcement has theoretical implications, and the deferred-feedback technique has many applications. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

某面板堆石坝沉降观测资料反馈分析

根据某面板堆石坝施工期、蓄水初期以及几年来的沉降观测资料，对坝体填筑材料计算参数进行反馈分析，得出了能够反映坝体实际变形的弹塑性应力变形计算参数，有利于今后建立大坝变形预报模型，更准确地把握大坝实时运行状态。     

陶瓷及陶瓷基复合材料微缺陷的超声检测

为研究陶瓷及陶瓷基复合材料微缺陷的超声检测能力，针对一些人工缺陷试样进行了超声检测试验。试验主要采用了纵波垂直入射法和泄漏瑞利波法。通过试验结果，比较了两种方法的检测能力。     

基于PC机群的大地电磁Occam反演并行计算研究

Occam反演以其稳定收敛和不依赖于初始模型的特性被广泛应用于大地电磁数据的处理，但偏导数矩阵的计算和拉格朗日乘子的求取导致大量的模型正演，使得反演速度较低。为此，研究了用基于PC机群的并行计算来解决这一问题的方法。首先对Occam反演方法进行了阐述；然后，分析了反演方法中各计算耗费的时间，提出对约占计算量90％的偏导数和拉格朗日乘子进行并行计算的思想，即偏导数计算采用频点计算一级的大粒度并行，拉格朗日乘子扫描和一维搜索分别采用弘值计算一级的大粒度并行和频点计算一级的小粒度并行；给出了并行计算的实现方法，即在PC机群上，利用主一从编程模式实现Occam反演的整体并行计算。在计算中，采用任务组合方式，减少了通信量，较好地实现了负载均衡。在4节点PC机群上，对应于拉格朗日乘子的扫描和一维搜索方式，整体加速比分别达到3．36和2．83。