应用独立分量分析的激光测风雷达湍流频谱分解

针对大型风力发电机机组中常见的脉动湍流、风机尾流与涡流等湍流信号,研究了利用自然梯度下降的独立分量分析方法的湍流频谱分离效果,以区分中心风速与湍流信号,提高风机机组的综合工作效率。首先分析了风机组中常见湍流信号的后向散射与频谱分布特点,然后依据这些特点设计了对应的独立分量分析模型。在仿真结果符合要求的基础上,进行了双目激光雷达天线的风速采集与实际分离效果检测。实验结果表明,在大气折射率结构常数C2n≤10-14同时广义大气常数α≥4的通常情况下,利用双目信号能够分离出一个湍流中心和一个中心风速。对1 s内两个谱峰的波动范围进行统计,获得(2.59±0.05)MHz的中心风速以及(1.22±0.19)MHz的湍流中心估计,且二者的平均信噪比分别为25.93 dB和31.01 dB,能够在获得稳定的中心风速估计的同时得到一个较为稳定的湍流中心估计。     

Maximum likelihood-based adaptive differential evolution identification algorithm for multivariable systems in the state-space form

Parameter estimation plays an important role in the field of system control. This article is concerned with the parameter estimation methods for multivariable systems in the state-space form. For the sake of solving the identification complexity caused by a large number of parameters in multivariable systems, we decompose the original multivariable system into some subsystems containing fewer parameters and study identification algorithms to estimate the parameters of each subsystem. By taking the maximum likelihood criterion function as the fitness function of the differential evolution algorithm, we present a maximum likelihood-based differential evolution (ML-DE) algorithm for parameter estimation. To improve the parameter estimation accuracy, we introduce the adaptive mutation factor and the adaptive crossover factor into the ML-DE algorithm and propose a maximum likelihood-based adaptive differential evolution algorithm. The simulation study indicates the efficiency of the proposed algorithms.     

河南渑池地区铝土矿工艺矿物学及锂的赋存状态研究

通过河南省渑池地区含锂铝土矿(岩)层工艺矿物学分析,查明铝土矿的物质组成、嵌布特征、伴生锂分布特征和赋存状态,为矿产综合利用提供理论依据。结果显示:该铝土矿Al2O3含量为54.8%,铝硅比值(A/S)为2.6,铝土矿层和粘土岩层中Li2O含量均高于伴生锂边界品位,粘土岩中锂更为富集；矿物组成除一水硬铝石之外,主要是以集合体形态产出的粘土矿物。采用稀酸解析、选矿测试和电子探针分析锂的赋存状态,查明矿石中锂主要是以类质同象置换形式赋存在伊利石和高岭石等粘土矿物中；选矿富锂尾矿中Li2O可富集到0.57%左右,是锂综合回收利用的重点研究对象。      

斗轮取料机液压控制系统的故障分析及改进

针对臂式斗轮取料机运行中抖动现象,进行了故障分析和排除,并对其液压原理和元件选型进行了优化及改进,为相关液压系统的故障分析和设计选型提供参考。     

紫金山东南矿段成矿期次、阶段浅析

通过对紫金山东南矿段铜钼(金)矿床地质矿化特征分析,指出铜钼矿化带主要赋存于花岗闪长斑岩的内外接触带,处于似斑状花岗闪长斑岩的上部,金矿化带赋存在表生氧化带的英安玢岩、隐爆角砾岩中。经过对矿石的组构特征、矿物生成顺序等特征分析,将矿床的成矿演化过程分为斑岩热液期、高硫化浅成低温热液期、表生氧化期三个主要矿化期次,进一步将斑岩热液期分为黑云母-钾长石化阶段、石英-绢云母化阶段、碳酸盐化阶段三个阶段;高硫化浅成低温热液期分为地开石化阶段、明矾石化阶段、硅化阶段三个阶段。研究结果为进一步研究矿床成因提供了依据。     

Etching characteristics of thin SiON films using a liquefied perfluorocarbon precursor of C6F12O with a low global warming potential

Perfluorocarbon gas is widely used in the semiconductor industry. However, perfluorocarbon has a negative effect on the global environment owing to its high global warming potential (GWP) value. An alternative solution is essential. Therefore, we evaluated the possibility of replacing conventional perfluorocarbon etching gases such as CHF₃ with C₆F₁₂O, which has a low GWP and is in a liquid state at room temperature. In this study, silicon oxynitride (SiON) films were plasma-etched using inductively coupled CF₄ +C₆F₁₂O+O₂ mixed plasmas. Subsequently, the etching characteristics of the film, such as etching rate, etching profile, selectivity over Si, and photoresist, were investigated. A double Langmuir probe was used and optical emission spectroscopy was performed for plasma diagnostics. In addition, a contact angle goniometer and x-ray photoelectron spectroscope were used to confirm the change in the surface properties of the etched SiON film surface. Consequently, the etching characteristics of the C₆F₁₂O mixed plasma exhibited a lower etching rate, higher SiON/Si selectivity, lower plasma damage, and more vertical etched profiles than the conventional CHF₃ mixed plasma. In addition, the C₆F₁₂O gas can be recovered in the liquid state, thereby decreasing global warming. These results confirmed that the C₆F₁₂O precursor can sufficiently replace the conventional etching gas.     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

Optimal design of nonlinear model predictive controller based on new modified multitracker optimization algorithm

The controller design for the robotic manipulator faces different challenges such as the system's nonlinearities and the uncertainties of the parameters. Furthermore, the tracking of different linear and nonlinear trajectories represents a vital role by the manipulator. This paper suggests an optimal design for the nonlinear model predictive control (NLMPC) based on a new improved intelligent technique and it is named modified multitracker optimization algorithm (MMTOA). The proposed modification of the MTOA is carried out based on opposition-based learning (OBL) and quasi OBL approaches. This modification improves the exploration behavior of the MTOA to prevent it from becoming trapped in a local optimum. The proposed method is applied on the robotic manipulator to track different linear and nonlinear trajectories. The NLMPC parameters are tuned by the MMTOA rather than the trial and error method of the designer. The proposed NLMPC based on MMTOA is compared with the original MTOA, genetic algorithm, and cuckoo search algorithm in literature. The superiority and effectiveness of the proposed controller are confirmed to track different linear and nonlinear trajectories. Furthermore, the robustness of the proposed method is emphasized against the uncertainties of the parameters.