接地故障保护的设置和整定(三)

7 TT系统接地故障保护 TT系统的电源中性点直接接地,而电气设备的外露可导电部分则经各自的PE线接地。这样在大多数情况下,由于故障回路包括两个接地电阻,使接地故障电流太小,不足以使过电流保护动作切断接地故障电流。而且由于故障电流小,故障点未被熔焊,故障点阻抗是难以估计的接触电阻。因此,TT系统接地故障回路阻抗和故障电流难以估算。所以,必须设置漏电电流动作保护。     

Mg-doped LiNi0.5Mn1.5O4 spinel for cathode materials

Lithium-ion batteries are becoming more and more important not only for portable electronic devices, but also in prevision of high power electric vehicles. In such an optic, deep studies regarding all the components of a secondary battery are in development. In this study, high voltage cathode materials have been selected. Crystals with spinel structure have a 3D vacancy pathway suitable for Li-ions transport. The material under study was LiNi_0.5Mn_1.5O₄ doped with magnesium replacing the nickel. Various samples were synthesized via three different routes: a solid-state method, a modified sol–gel method and a xerogel method. The structure and morphology of the powders were analyzed with HRTEM and XRD. Electrochemical tests were also performed. A wide range of particle sizes (from micro to nanosize) was the result of the different synthesis routes. Unfortunately pure materials were not always obtained. The electrochemical tests showed improvement of the material's cyclability, by reducing the particle size. The electrochemical tests further confirmed the existence of a Li_1+dMn_2−dO₄ impurity. The results are quite promising, however, further improvement of the purity of the electrode composition are needed.     

Scanning electron microscope electron detector with a radial type discrete dynode electron multiplier

A discrete dynode electron multiplier with radial flux of electrons was built and tested in the range of low‐voltage scanning electron microscopy as a backscattered electron detector of topographic contrast. The multiplier collects backscattered electron emitted in a specific range of take‐off angles and over the whole azimuth angular range enabling large solid collection angle. Multipliers with different dynode shapes were studied theoretically with the use of the software for particle optics and three assemblies were built and tested experimentally. The gain estimation, assessment of the type of detected electrons (secondary electron or backscattered electron), imaging the spatial collection efficiency and signal‐to‐noise measurements were performed.     

阳极炭块压降测试的方法与分析

本文通过阐述新的阳极炭块测试方法，提出了降低阳极炭块Fe-C压降的思路，并分析了降低阳极炭块压降对我公司经济效益的影响，可供同行参考。     

An investigation of the relation between the temperature dependences of the initial unbalance and the output signal of resistance strain sensor bridge circuits

The relation between the initial unbalance and the output signal of bridge circuits when acted upon simultaneously by the physical factor being measured and the temperature of the surroundings when the bridge is supplied from a voltage or current source is investigated. Analytic relations are obtained which explain the temperature dependence of the useful output voltage under external physical action. __________ Translated from Izmeritel’naya Tekhnika, No. 1, pp. 48–49, 2007.     

智能型MNS低压开关柜

MNS智能低压开关柜是ABB公司的新一代产品。除具有设计灵活、结构紧凑和免维护等特点外，安全可靠性是其最突出的优点，包括抗故障电弧、可靠的绝缘分隔及接插性能、可靠的抽屉单元和温升限制。采用和智能化电动机控制中心INSUM及配电智能化控制和能量管理系统ESD2000的完美结合，开发了了基于现场总线的智能化的系统解决方案。     

位置控制器与通用变频器APC系统

在每一周期的开始时的速度值V1预设定到传动装置上进行速度预控制，同时，反馈回来的实际值Sj与S1进行比较计算，得出当时偏差值△S，此偏差值△S乘以比例系数Ksp，得到Vk叠加在Vt上，得出传动装置应具有的速度控制信号V，然后V经速度／电压变换和D／A转换向传动系统的速度控制发出控制信号Uα控制执行机构的定位。调节Ksp的值使系统无超调无振荡。     

钕电解阳极过电位的测定

用慢扫描示波法测定了钕电解的阳极过电位 .考察了温度、阳极电流密度、Nd2 O3添加量、电解质组成等因素对阳极过电位的影响 ,探讨了降低阳极过电位的可能途径 .结果表明 ,阳极过电位随阳极电流密度的增加而增大 ,随温度的升高而减小 ,一定范围内 ,阳极过电位与阳极电流密度的对数呈线性关系 ,满足塔菲尔方程 ;电解质中LiF和Nd2 O3浓度增加 ,阳极过电位降低 ;适当控制阳极电流密度、升高温度、增加电解质中LiF和Nd2 O3的浓度并尽可能减小极间距 ,均有利于降低阳极过电位     

液晶电控效应的实验研究

详细阐述了液晶的电光效应,介绍了利用分光光度计测量液晶透射比的方法。通过改变加在液晶盒上的电压大小及其频率高低,详细测量了液晶的透射比。通过做图分析了液晶的电控双折射效应,得出液晶的透射比随所加电压的大小和频率的高低而变化,以及液晶的阈值电压随频率的增高而减小的规律,这对液晶器件的设计与研究均具有一定的参考价值。     

Parallelization of WHILE loops on pipelined architectures

Modulo scheduling theory can be applied successfully to overlap Fortran DO loops on pipelined computers issuing multiple operations per cycle both with and without special loop architectural support. This paper shows that a broader class of loops—REPEAT-UNTIL, WHILE, and loops with more than one exit, in which the trip count is not known beforehand—can also be overlapped efficiently on multiple-issue pipelined machines. The approach is described with respect to a specific machine model, but it can be extended to other models. Special features in the architecture, as well as compiler representations for accelerating these loop constructs, are discussed. Performance results are presented for a few select examples.An earlier version of this paper was presented at Supercomputing '90.