大功率CO2激光器脉冲电源研究

本文论述了直流高压与高频脉冲电源相叠加，构成高频、高压脉冲电源，并使其对CO2激光器进行放电实验，研究了同条件下的放电参数与功率。     

经济实用的DSP电源解决方案

笔者介绍了两种低纹波的DSP电源解决方案:一为采用MAX1793和大电流EMI静噪滤波器NFM41P;二为改进的去耦p型滤波电路和大电流EMI静噪滤波器NFM41P。并对方案的特点及其实现进行了详细的解析。试验结果表明:所述方案的纹波小,仅100 mV左右;成本低,仅几十元;适用范围广,通过改变MAX1793芯片的输出电压,可将本方案移植到TI的C5000,C6000系列,且还可用于其他的脱机工作系统。     

中国未来电力需求与核能

本文介绍了我国未来电力需求和能源结构，阐述了核能是我国满足经济发达地区电力需求的合理选择，并提出了我国“九五”核电计划和中期目标，以及发展核电中面临的问题和基本对策。     

金属换热器选用经济分析

本文以系统节能和提高综合经济效益的观点，分析了金属换热器传热系数的影响因素及提高途径；气流阻力与动力消耗；传热面积与投资的定量关系。为正确选用不同结构金属换热器及其性能提供了依据。     

国防计量工作改革的探讨

阐述了国防计量与民用计量的差别，计量工作的原动力以及对国防计量工作改革的探讨。     

Control strategies for reactive batch distillation

A batch reactor may be combined directly with a distillation column by distilling off the light component product in order to increase the reactor temperature or to improve the product yield of an equilibrium reaction. The same amount of the light product should be removed as the amount being formed by the reaction at any time. A linearized model has been developed which describes the process behaviour satisfactorily for control analysis purposes. The controllability of a combined batch reactor/batch distillation column is found to depend strongly on the operating conditions and on the time during the run. In general, controlling only the reactor temperature (one-point bottom control) is difficult since the set-point has to be specified below a maximum value in order to avoid break-through of an intermediate component in the ditillate. This maximum value may be difficult to know a priori. For the example considered in this study, control of both reactor temperature and distillate composition (two-point control) is also found to be difficult due to large interactions in the column. As with one-point bottom control, the reactor temperature has to be specified below a maximum value. However, energy can be saved since the heat duty can be decreased with time. Controlling the temperature on a tray in the column (one-point column control) is found to give good performance for the given process with no loss of reactant and a high reactor temperature, although no direct control of the reactor temperature is obtained.     

采用区内C／I平衡的多区峰窝CDMA系统下行链路的性能

本文对采用区内Ｃ／Ｉ平衡的多区蜂窝ＣＤＭＡ系统下行链路的性能进行分析，给出两种区内Ｃ／Ｉ平衡算法并比较它们的性能，考虑呈对数正态分布的阴影和Ｒ＾－４规律的路径损失的综合影响，采用与传统不同的小区平均中断概率来评价系统的性能。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

核电材料在模拟反应堆环境中应力腐蚀破裂测试技术与性能评价

简要介绍了采用慢应变速率试验，Ｕ型弯曲和Ｃ形环试验等技术，分别对８００合金，３０４和３１６及３１６Ｔｉ不锈钢Ａ５３３Ｂ压力容器用多在模拟核反应堆环境中的应力腐蚀破裂敏感性性进行的试验研究的一些主要结果；并结合电化学测试和表面膜俄歇电子能谱分析结果进行了讨论。     

自动力套管补贴加固技术及其在B125井的应用

随着油田开发时间的延长，油水井井下套管的损坏将越来越严重，套管故障井将越来越多，为了恢复套损井生产，将套管损坏所造成的损失降到最低，在配套波纹管补贴，水动力补贴，爆炸补贴等专门修套技术的基础上，通过认真调查研究，又配套了操作方便简单，适用套管损坏类型广的自动力套管补贴加固技术，使各种套管变形，套管断错（错开没有位移或位移量不大时）、套管破裂，误射孔井段封堵，已射开水层封堵等修井作业的难度进一步降低，从而进一步提高了修复井综合开发经济效益。