X-Ray Measurement of Residual Stress in Plastic Bonded Explosives

The X-ray diffractive technology was adopted for tentative study of plastic bonded explosive. The datum of some new diffractive peaks in standard PDF cards were added. The effects of strain to interplanar distance and crystal size of the explosive were studied. The results show that grain size of plastic bonded explosive is decreasing with the increasing of the pressure, and the residual stress of the explosive is draw stress.     

油藏数值模拟在油田开发调整中的应用——八面河油田面4区面3块开发调整方案研究

针对油藏现状,在油藏描述的基础上,进行网格划分,建立地质模型;根据生产历史资料建立动态模型;通过对油藏模型参数的分析,建立油藏数值模拟模型;应用数值模拟软件对面3块进行了三维三相油藏数值模拟研究。根据拟合成果提交了含水饱和度分布图、单位面积剩余储量分布图和各砂体储量状况表,分析了剩余油分布规律和油藏开发潜力,对面3块进行了调整方案设计和调整后的效果分析。     

Effect of surfactants on phenol removal by the method of polymerization and precipitation catalysed by Coprinus cinereus peroxidase

The removal of phenol by peroxidase‐catalysed polymerization was examined using Coprinus cinereus peroxidase in the presence of surfactants. The non‐ionic surfactants with poly(oxyethene) residues, Triton X‐100, Triton X‐405 and Tween 20, enhanced the phenol removal efficiency at a level similar to high relative molecular mass poly(ethylene glycol) (relative molecular mass 3000). Although the improvement in the removal efficiency was less than that of Triton X‐100, Span 20, sodium lauryl sulfate (SDS) and lauryl trimethylammonium bromide (DTAB) also enhanced the removal efficiency. The requirement of the enzyme for almost 100% removal of 100 mg dm^?3 phenol decreased to one‐fourth by the addition of 30 mg dm^?3 Triton X‐100. Triton X‐100, Triton X‐405, Tween 20 and DTAB could reactivate the enzyme precipitated with the phenol polymer, leading to the restarting of the phenol removal reaction. Copyright © 2003 Society of Chemical Industry     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

基于网络的家电产品故障诊断系统研究

介绍了基于网络的家电产品故障诊断系统的硬件拓扑结构、软件平台及系统开发。系统在硬件上采用了多种网络平台搭建方式及综合连接技术，软件上采用了IDRS诊断模型和基于事例的最新诊断技术。这也是诊断研究和应用的新领域。     

机械定尺飞锯机中的555时基电路

介绍了５５５时基电路在机械定尺飞锯机中的应用及工作原理。     

孔径法测量铜带残余应力的试验研究

介绍了用于薄板残余应力测量的新方法——孔径法,该方法是通过测量冲孔直径的变化来间接求出各方向的残余应力;文中详细阐述了残余应力的标定方法;由于可针对不同材料建立了被测材料的平均应力(σ_l)与被测板材宽度(B)、厚度(H)以及冲孔后直径变化率(△D_i/D)之间的数学模型,因而使薄板残余应力测量变得简便而经济;此外还对该方法的分辨率与测量精度进行了实验、计算与分析。     

High-temperature,high-pressure thermophysical measurements on liquid zinc

Wire-shaped zinc samples were resistively volume heated as part of a fast-capacitor discharge circuit. Time-resolved measurements with submicrosecond resolution of the current through the specimen, the voltage drop across it, and the thermal expansion of the specimen as a function of time allow determination of the enthalpy, electrical resistivity, and density at different temperatures up to superheated liquid states of zinc far above the normal boiling point. High static pressures, up to 3800 bar of the ambient medium water, were used. An estimate of the critical pressure for zinc is given by investigations of the stability of the sample with a framing CCD camera, taking pictures of different samples varying the ambient static pressure. The critical volume and the critical temperature are obtained by means of an extrapolation of measured data at different pressures.Paper presented at the Fourth International Workshop on Subsecond Thermophysics, June 27–29, 1995, Köln, Germany.     

Rene′95粉末合金喷丸强化研究

研究了Ｒｅｎｅ′９５热等静压粉末高温合金喷丸后的残余应力场、组织结构、致密度及其与疲劳性能的关系。结果指出，喷丸强化能够有效地提高合金高周和低周疲劳强度。     

用发展的Sachs法研究模拟轧辊中的残余应力

对不同辊型，尺寸，材料与加工处理方法的模拟冷轧辊进行了内剥层试验研究，求出了原辊和打中心孔或扩孔后辊内残余应力分布曲线，提出了虚拟打孔法和虚拟剥层法，解决了实心辊中心和空心辊内表层的残余应力的精确测量问题，丰富了Ｓａｃｈｓ内剥层法的内容，机械法打中心孔，热处理前打中心孔，空心辊表淬前改变温度场的方法可降低残余应力值，后者降低残余应力的效果尤为显著。