高斜效率高功率850nm氧化限制型垂直腔面发射激光器

报道了MOCVD生长的高性能850nm氧化限制型垂直腔面发射激光器.研制出的氧化直径为9μm的激光器25℃时的斜效率和阈值电流分别为0.82mW/mA和2.59mA,激光器在23mA时输出16mW最大光功率.氧化直径为5μm的激光器25℃时的最小阈值电流为570μA,其最大饱和光功率为5.5mW.     

区域水土特性参数时空变异分布特征及相关分析

作者应用地质统计学原理与方法,在山东簸箕李引黄灌区开展大尺度区域水土特性参数时空变异性的研究,描述农田排水、地下水、表层土壤中含盐量的空间与时间变化分布趋势和特征,分析其间存在的相关关系。结果表明,在一个完整的水文循环年内,研究区域的水土特性参数之间具有相近的空间变异分布状态和特点,但却表现出不同的时间变异分布趋势与特征。农田排水和表层土壤的含盐量随季节变化的分布状态在灌区上、下游相对稳定,在中游却变化明显;地下水的盐分浓度在整个灌区的分布状况没有呈现出明显的时间变异性。在春季至初夏时段内,农田排水中含盐量的增加似乎对地下水水质的影响较小,而对表层土壤积盐状况影响较大。研究成果为灌区制定合理的水资源利用与农田水土管理策略提供了理论依据。     

堆石料与基岩面直剪试验

介绍了堆石料与基岩面的现场直剪试验方法，6个组次的直剪试验结果表明，堆石料与基岩面的抗剪强度指标随基岩面坚硬度的增大而增加，并随基岩面粗糙度的加大而加大。     

一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

The Soft-Contact Method and Instruments for Measuring the Surface Temperature of Solids

A method and instruments based on it are proposed for the contact measurement of surface temperature when carrying out industrial experiments and when monitoring technological parameters.     

不同表面预处理对有机电致发光显示器性能的影响

从生产角度研究了基板表面的预处理工艺对OLED性能的影响,分别用UVOzone、氧Plasma以及两者相结合的方式对基板进行表面处理,并按照生产工艺制作器件,从接触角、方阻以及光电特性等测试结果对各种表面处理的样品进行比较。结果表明以上处理都改善了器件性能,不同程度提高了器件的清洁度、亮度和发光效率,其中UVOzone和氧Plasma结合的方式处理效果最为显著,器件在10V时亮度达到79920cd/m2,比其他两种处理方式亮度提高约25%。     

LARGE EDDY SIMULATION OF VERTICAL JET IMPINGEMENT WITH A FREE SURFACE

1. INTRODUCTION When wastewater is discharged into rivers, lakes or oceans, it usually leads to the formulation of turbulent jet with a free surface. If the ambient water depth is shallow, the jet will impinge on the water surface and the confinement of f…     

高温酸化助排剂HC2-1的研究

为了满足高温油藏和深井酸化作业残酸返排的需要，通过表面活性剂的筛选和复配研究，得到了高温酸化助排剂HC2—1。其性能评价结果表明，HC2—1具有使用浓度低、表面活性高的特点，在20％的HCI溶液中，当其浓度为50mg／L时，表面张力为20．7mN／m；具有良好的耐温性能，在180℃下恒温48h，HC2—1仍保持较高的表面活性；具有良好的耐盐能力，加有HC2—1的20％HCl溶液和CaCO3反应至HCl完全消耗，整个反应过程体系无新相生成且表面张力基本不变；可增大酸液体系的润湿角，进一步降低毛细管阻力，使酸液返排率由46％提高到97％，在促进酸液返排的同时与原油不发生乳化反应。     

A New Approach for Built‐in Self‐Test of 4.5 to 5.5 GHz Low‐Noise Amplifiers

This paper presents a low‐cost RF parameter estimation technique using a new RF built‐in self‐test (BIST) circuit and efficient DC measurement for 4.5 to 5.5 GHz low noise amplifiers (LNAs). The BIST circuit measures gain, noise figure, input impedance, and input return loss for an LNA. The BIST circuit is designed using 0.18 μm SiGe technology. The test technique utilizes input impedance matching and output DC voltage measurements. The technique is simple and inexpensive.     

Fatigue limit evaluation of notches,small cracks and defects: an engineering approach

In this paper, the average stress method for the fatigue limit evaluation of stress raising geometrical features is revised and extended. In particular, an analytical close‐form approach was used and the linear elastic stress equations were modified by taking into account the effect of nominal stress on the local stress distribution. Hence, the average tangential stress was correctly evaluated over a distance of 2a₀, where a₀ was El Haddad's short crack constant, for long and small notches as well as for crack‐like notches. When this model is applied to a wide range of geometrical features subjected to mode I fatigue loading, the classical shape of the curves of the Kitagawa–Takahashi diagram was obtained for changes in crack‐like notch size. Similarly, notch sensitivity was estimated by reducing the notch tip radius. The accuracy of the proposed method in predicting fatigue limits was then checked by using experimental data taken from the literature and generated on testing specimens weakened by rounded and sharp notches as well as by small artificial defects.