炼油废白土在水泥厂燃煤自备电厂中再利用的实践

本项目主要研究和实现了工业废白土在BAYAH燃煤自备电厂中的再利用,实现变废为宝,减少了环境污染,同时为企业创造了一定的经济效益。针对废白土的特性,对燃料输送系统给煤机、皮带机、煤仓、下料溜子和排渣系统进行了改造。通过修改操作规程消除废白土对锅炉运行的影响。     

PC2425锤式破碎机的篦子改造

PC2425破碎机是较为常用的锤式破碎机规格之一，主要用于石灰石的破碎，台时产量800~1 000 t，出料粒度≤70 mm，筛余5%，配套4 500~5 000 t水泥生产线。PC2425破碎机篦条为易损件，由于物料的冲击会导致篦条变形，但其原有的弓形架与篦条型式，更换时很难将篦条从弓形架中抽出，导致更换非常不便。此次改造，用户最初适量降低破碎机的出料粒度，以提高生料磨的产量及降低生料粉磨的电耗，虽然通过调整篦条与锤头的间距及篦条间隙可以达到降低出料粒度的要求。但是为了彻底解决篦条更换困难问题，重新设计了篦架结构。     

超亲水毛细芯环路热管启动及热性能分析

为解决电子设备高热通量下的散热问题，采用H₂O₂氧化法对烧结毛细芯进行了超亲水改性，研究了毛细芯表面润湿性对吸液性能的影响。并将改性后的超亲水毛细芯应用到环路热管内，研究了倾斜角度及加热功率对超亲水毛细芯环路热管的换热特性的影响。实验结果表明：超亲水毛细芯的吸液速度增加，吸液时间较亲水毛细芯减小了3.52ms；与普通亲水毛细芯环路热管相比，在加热功率Q=200W时，超亲水毛细芯环路热管蒸发器中心温度降低了约6.0℃，在Q=20W时启动时间与温度分别降低了33s与2.5℃。同时发现超亲水毛细芯环路热管在正重力状态时的运行温度更低，热阻较小，最低热阻仅为0.084℃/W。     

基于粒子群优化算法的五自由度机械臂轨迹规划

为了让机械臂的工作时间达到最优,以自主研发的抛光机器人样机为研究对象,针对手表表壳表耳部分的抛光过程,提出PSO算法对五自由度机械臂轨迹规划进行优化,并通过MATLAB软件进行机械臂的仿真与分析。仿真结果表明,基于PSO算法的轨迹规划使机械臂在工作过程中加加速度不会产生突变,运动轨迹精度高,机械臂工作时间达到最优。     

Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

综放面本煤层预抽瓦斯的治理技术

为了极大限度地提高本煤层预抽效果，以马兰煤矿为研究对象，针对目前马兰煤矿的瓦斯赋存情况和现阶段所采取的抽放措施，从抽放钻孔的孔径、孔深、布置方式、封孔质量和增加煤层透气性等方面进行探索。实践表明，以上方法的运用，能够有效地提高本煤层预抽抽放效果，保证工作面安全生产。     

Effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter using CFD

The effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter has been evaluated using computational fluid dynamics (CFD). The shear stress transport k-ω (SST k-ω) turbulence model has been adopted for closure. The performance of two V-cone flowmeters with different beta ratios (β) viz., 0.6 and 0.7 for a fixed vertex angle (ϕ) of 60° has been analysed as a function of Reynolds number (Re). The results show that the coefficient of discharge (C_d) increases with Reynolds number in the laminar and transition flow regimes whereas it is nearly constant in turbulent flow regime. From the results, it can be concluded that C_d is independent of Re for values equal to 4000 and beyond. Further, it is also seen that the performance of the V-cone flowmeter is not affected by the upstream boundary layer thickness if the velocity profiles having different boundary layer thickness are extracted from an axial distance of 10D and more are fed at 5D upstream of the meter. However, the meter is sensitive to the extracted velocity profile from an axial distance of 5D and uniform velocity profile being fed at 5D upstream. The value of C_d may be sensitive as a result of the pressure variation due to the obstruction.     

不同工质回路热管负载功率变化下的质量流量特性

为了进一步提高回路热管仿真精度并丰富回路热管实验研究方法，本文对回路热管瞬态传质进行实验研究。使用高精度质量流量计分别对以丙酮、乙醇、丙烯为工质的回路热管进行不同负载功率下的质量流量测量研究。结果表明：启动阶段，热负载10W时，丙烯回路比丙酮回路热管启动快，且两者的温度稳定均滞后于质量流量；稳定阶段，随着热负载功率增大，不同工质的回路热管的平均质量流量均线性增长，而瞬态质量流量则持续波动，其质量流量波动幅度均呈现先减小后增大的趋势。质量流量波动幅度会受到气体工质的可压缩性与作用在毛细芯内部上的热量的共同影响。通过频谱分析发现，液相质量流量波动还会受到冷凝器两相区的影响。高热负载下，作用在毛细芯内部上的热量占主导地位，质量流量波动加剧，同时出现周期性大幅波动，且其波动频率随着热负载增大而增大。     

肠靶向海藻酸钙基微胶囊的制备及控释性能研究

利用毛细管共挤出技术结合静电吸附和仿生硅化的方法，制备了海藻酸钙-壳聚糖/精蛋白/二氧化硅(ACPSi)复合微胶囊。ACPSi复合微胶囊的平均粒径约3.18 mm，单分散性好，囊壁最外层的二氧化硅层可抑制其在肠液pH环境中的溶胀，增强囊的机械稳定性。将羟丙甲基纤维素邻苯二甲酸酯(HPMCP)肠溶微球作为释药“微阀门”，嵌入囊壁可以更好地控制微胶囊的释药行为。以吲哚美辛为模型药物，当药物浓度为22.5 mg/ml时，ACPSi载药微胶囊在pH 2.5模拟胃液中3 h时累计释药率仅为0.33%，而转移至pH 6.8模拟肠液中19 h时累计释药率为77.78%；囊壁嵌入HPMCP微球后，22 h时累计释药率可提高约4%。因此，该复合微胶囊具有良好的肠靶向作用和控释特性，作为口服肠靶向缓控释制剂具有良好的应用前景。     

Longitudinal permeability determination of dual-scale fibrous materials

In this work, the longitudinal permeability of squarely packed dual-scale fiber preforms is studied theoretically. These fiber preforms are composed of aligned porous tows and the tows are tightly packed. The effective permeability is calculated as a parallel-like network of intra-tow permeability and inter-tow permeability, which are quantified by Darcy’s law and the inscribed radius between tows, respectively. The jump velocity at the interface between inter-tow fluids and porous tows is considered, as derived by substituting Beavers and Joseph’s correlation into Brinkman’s equation. We further examine the effects of intra-tow permeability on the effective permeability of the fibrous system with three interface conditions: (1) interface velocity = 0, (2) interface velocity = mean intra-tow velocity, and (3) interface velocity = jump velocity. The jump-velocity-based model is found to be closest to numerical data. The influence of the fiber volume fraction of tows on the effective permeability is also analyzed.