Top illuminated organic photodetectors with dielectric/metal/dielectric transparent anode

The top illuminated organic photodetectors (OPDs) with a Dielectric/Metal/Dielectric (DMD) transparent anode are fabricated. The transparent electrode is composed of molybdenum trioxide (MoO₃)/silver (Ag)/MoO₃ layers and zinc oxide (ZnO)/aluminum (Al) is used for bottom cathode. The optimized DMD electrode has an optical transmittance of 85.7% at the wavelength of 546 nm and sheet resistance of ∼6 Ω/sq. The fabricated OPDs exhibit a high detectivity and wide range linearity.     

不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。     

燃料电池空气电极的孔道结构调控

燃料电池是将化学能转化成电能的装置，其空气电极催化层的设计，既要包含丰富的、易于接近的反应活性位，也要具备高度连通的电子、质子以及反应物、产物传质通道，因此电极必须具有特定三维几何结构形貌和有序分布的各功能化孔道，确保催化活性位得以充分利用以及反应可以连续进行。针对催化剂孔道的几何结构调控，本文调研了最近报道的一系列研究工作，从模板法、高温相变法、模板/相变复合方法以及基于金属有机框架材料进行孔道设计等四种主要方法出发，综述了该领域的最新研究进展。     

多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。     

The formation of fibrous structure of polyamide 6 induced by the three-step forming process and its prominent reinforcement in nitrile rubber

Nitrile rubber (NBR) blends with excellent performance have always been a hot research topic in petroleum field. Due to the excellent performance and compatibility of polyamide 6 (PA6), it provides an opportunity for the preparation of high-performance NBR/PA6 blends. In this article, NBR/PA6 blends were prepared by the three-step molding process. Experimentally, it was found that PA6 has a prominent reinforcement effect in NBR matrix. The variation of this mechanical property was investigated from different aspects of the crystal structure, crystallinities, phase morphology, and so on. It can be cleared that the formation of fibrous structure of PA6 phase is the main factor for reinforcement of the polymer blends. Meanwhile, the formation mechanism of the special phase structure induced by the three-step process is deeply expounded and its structural evolution schematic is established. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47472.     

绿色化工技术在精细化工中的应用研究

社会经济快速发展,科学技术不断进步,针对我国现代工业化工行业发展,所产生的新型化工技术应用,促进我国化工生产效率的提升。工业的发展不可避免地会带来污染物的产生,如果不能有效控制化工排放污染物,温室效应问题会更加严重。本文对绿色化工技术在精细化工中的有效应用进行研究,降低工业废气污染物排放量,维护生态环境平衡。     

不同含量低污染水对人工湿地中细菌的影响研究

探究水平流人工湿地(HFCW)系统处理低污染水过程中,相同COD/ρ(TN)下不同碳氮含量对细菌群落结构的影响。结果表明,进水为较高碳氮含量的HFCW(HF1)和进水为较低碳氮含量的HFCW(HF2)对COD和TN的去除效率具有一定的差异,HF1和HF2对COD的去除效率分别为48.26%和28.89%,对TN的去除率分别为79.06%和81.87%。HF1中细菌的丰富度和多样性均高于HF2,HF1中富集的优势细菌为Chloroflexaceae、Comamonadaceae和Rhodocyclaceae,均具有异养反硝化功能,HF2中富集的优势细菌为Xanthomonadaceae和Rhodocyclaceae,其中Xanthomonadaceae具有自养反硝化功能。COD、NH4^+-N和NO3^--N对HF1中细菌群落的影响大于对HF2中细菌群落的影响,HF1中COD对细菌群落的影响大于NH4^+-N和NO3^--N。     

某铁矿隔水护顶矿柱厚度计算及安全影响预测

科学合理地确定矿山隔水护顶矿柱安全厚度是矿山安全生产的前提条件，为保障某铁矿地表民房、道路等建（构）筑物安全，防止矿山开采过程中产生的导水裂隙带贯通第四系含水层，采用荷载传递交汇线法、K.B.鲁别涅依他估算法和冒落带、导水裂隙带高度估算法3种理论分析方法对隔水护顶矿柱厚度进行计算，并利用数值模拟手段对留设隔水护顶矿柱后的开采过程安全影响进行了分析，对理论计算结果进行了验证。3种理论计算方法得出的隔水护顶矿柱厚度分别为14.3～17.3 m、17.5～31.4 m和41.8～57.4 m，推荐隔水护顶矿柱留设厚度为60 m。通过数值模拟分析得出，在留设60 m厚的隔水护顶矿柱的基础上，开采区域和隔水护顶矿柱位置产生的最大拉应力约0.47 MPa，矿山开采不会对隔水护顶矿柱造成破坏；地表产生的最大水平位移约5.8 cm，最大垂直位移约26.5 cm，最大倾斜为1.70 mm/m，最大曲率为0.20 mm/m2，最大水平变形值为0.70 mm/m，满足相关规范要求，预测矿山开采不会造成地表建（构）筑物破坏。     

Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.