以YAG为添加剂的气压烧结氮化硅

本文以添加ＹＡＧ的反应烧结氮化硅（ＲＢＳＮ）为前驱体，采用气氛加压烧结的工艺，在０．５～９．０ＭＰａ氮气压力范围，研究了不同氮压对烧结体的密度、相组成、强度和显微结构的影响及其相互间的关系。研究表明，通过改变氮气压力能有效地调控材料的显微结构，材料的性能又受控于显微结构的变化。     

直缝焊管机组生产冷弯型钢产品初探

主要介绍了φ２１９直缝焊管机组生产高速公路护栏 成型原理、工艺布置、变形方式、变形图和轧辊设计。     

发动机扭矩与转速关系经验公式试验研究

在对发动机外特性曲线扭矩与转速实验数据分析的基础上，对原有的经验公式进行了分析、改进，提出了新的经验公式．由这一经验公式所计算的数值，在最大扭矩与最大功率点之间，可与实验数据拟合得很好．与原经验曲线相比，新经验曲线与实验曲线的离差可下降50％以上．     

线加权余量法及其在正交异性板弯曲分析中的应用

利用有限差分法对控制方程和边界条件进行半离散化,使其定义在一些离散线上,然后采用加权余量法求解。这就是本文提出的线加权余量法,也可称之为有限差分-加权余量分维耦合法。文中以正交各向异性薄板弯曲平衡问题为例推导了有关具体算式,给出了数值算例,说明了本文方法的有效性。     

基于空间矩的灰度边缘亚像元度量精度分析

灰度图像中边缘定位受采样密度限制，亚像元精度度量方法在需要高精度的应用中受到重视，要想知识到底需要多高的分辨率才能达到定精度指标，就有必要分析特征定位方法的最坏情况的精度，文中用分析和实验的方法给出了基于空间矩的边缘定位方法，对于边缘点，边缘直线以及直边缘区域的最坏情况定位精度分析。分析和讨论的结果不但可以用来确定已知形状位置估计的最大误差，而且还可用于对准的形状几何参数，以获得较高的精度。     

人工神经网络技术在板料激光弯曲中的应用

基于人工神经网络基本理论,建立在板料激光弯曲中预测材料表面最高温度、弯曲角度的BP网络模型。借助于MATLAB仿真软件中的神经网络工具箱作为开发平台,将试验样本数据和经过试验验证的数值计算结果作为补充的样本数据用于BP网络的训练,利用训练好的BP网络对非线性的样本数据规律进行拟合,实现激光加工工艺参数的优化,为实际生产和加工提供有效的依据。     

Displacement Discontinuity Method for Fracture Mechanics Analysis of Reissner Plates: Static and Dynamic

This paper is concerned with the displacement discontinuity method applied to the shear deformable plates (Reissner’s and Mindlin’s theories) with cracks subjected to static and dynamic loads. Fundamental solutions of dislocation are derived using the Fourier transform method and the Laplace transformation technique. Boundary integral equations are presented in terms of rotations/displacement on the crack surfaces. The Chebyshev polynomials of the second kind are used to evaluate the integral equations with hypersingular kernels on the crack boundaries and determine the stress intensity factors at the crack tips. Comparisons are made with other numerical solutions to demonstrate the proposed method is accurate both for static and dynamic problems.     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

硬地层定向井中几种侧钻方法的灵活应用

在川渝地区，钻定向井、水平井必然要面对地层岩性变化大、硬度高等复杂地质情况，常常会遇到因井下复杂、事故、修改地质目标等原因需要填井侧钻。侧钻的方法不同，侧钻的成功率和效率差异很大。文中分析了川渝地区近几年硬地层定向井、水平井侧钻效率不高、有时甚至失败的原因，归纳总结了近几年常用的几种侧钻方法的施工效果，提出要根据具体条件灵活应用这几种侧钻方法。     

Stress State of Bent Buried Pipelines

The authors consider edge effects in buried pipelines that occur in the region of joining of a straight buried pipe and a bent insert (factory bend, elbow, or an elastically bent segment). The action of those effects results in the appearance of additional bending moments, which are proportional to the difference between the axial force in an infinite straight pipeline and that in a closed-end pipe, and depend on the geometrical parameters of the pipeline and physical-mechanical characteristics of the soil. Specific examples of analysis of elastic interaction of a pipeline with the soil for pipe bends with various radii of the bend arc are offered. It is shown that additional bending stresses may exceed appreciably the stresses from the axial force, and therefore, they should be taken into account when designing and building pipelines. The solution for an elastically bent segment has been obtained and analyzed.