非全日制研究生线上线下混合式教学模式研究 ——以《现代电气控制技术》为例

随着教育信息化技术的发展，线上线下混合式教学模式已成为一种趋势。为了解决非全日制研究生课堂教学召集困难、效果不佳等问题，提出了基于“互联网＋虚拟仿真技术”的线上线下混合式教学模式。本文以控制工程专业学位研究生为例，结合《现代电气控制技术》课程，探讨了线上线下混合式教学实现途径、师生互动方法、项目驱动案例教学法以及电气控制系统虚拟仿真实验平台的构建方法，切实提升非全日制研究生的培养质量。     

径向不耦合装药爆破效果的数值研究

为了研究径向不耦合条件下爆破效果的影响因素,利用AUTODYN-2D对比不耦合系数、不耦合介质、炸药种类对爆破效果的影响规律。结果表明,与耦合装药相比,径向不耦合装药条件下炮孔压力明显降低。对比水介质和空气介质下的爆破效果可知,水介质不耦合条件下,炸药爆炸能量的传递效率更高。炮孔压力与炸药种类密切相关,TNT产生的炮孔压力最大,但作用时间较短,而ANFO和乳化炸药的作用时间较长。     

基于(火用)效率目标的环冷机余热回收系统操作参数优化

摘要：针对烧结环冷机余热回收利用率不高的难题，采用分析法建立了评价某钢铁厂烧结环冷机余热回收系统运行效率的效率模型。基于多孔介质模型、局部非热平衡方程、真实气体SRK方程建立环冷机内气固两相换热模型。通过CFD仿真模拟，探究料层高度、循环风机输入烟气温度、烧结矿底部入口风速三项可控环冷机运行工艺参数对系统效率的影响规律。结果表明，料层厚度在1～1.5 m区间每增加0.1 m，效率增加0.8%～1.1%；循环风温在100～140℃之间每增加10℃，效率增加1.4%～1.5%；烧结矿底部入口风速在0.9～1.9 m/s之间每增加0.1 m/s，效率降低0.18%～0.24%。在此基础上，基于工业运行数据建立效率正交试验优化模型，提高了该余热回收系统3.42%的效率。     

气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

Computational modelling of water flow inside laboratory Knelson concentrator bowl

Enhanced gravity concentrators such as Knelson concentrator (KC) are extensively used in the mineral processing industry. The complexities of KC bowl geometry and variation of feed characteristics have forced process engineers to design empirically new units using laboratory and pilot-scale Knelson concentrators. However, numerical modelling methods such as computational fluid dynamics (CFD) and discrete element method (DEM) provide a better insight of flow behaviour of fluid and particulate solid phases inside these processing units. This article reports findings of CFD simulations for single-phase water flow inside the laboratory KC. An available standard 7.5-cm laboratory KC bowl was numerically simulated using realisable k-ε turbulence model to resolve the turbulence dispersion of existing transitional flow regime. The effects of relative centrifugal force (RCF) intensity and bed fluidisation water flow rate on the water velocity and pressure distributions were studied. Simulations confirmed the swirling flow pattern governing inside the bowl. The results revealed that the impact of RCF intensity on the water field values is greater than that of bed fluidisation water flow rate. Both velocity and pressure variations inside the bowl rings followed a linear trend.     

Transport Map sampling with PGD model reduction for fast dynamical Bayesian data assimilation

The motivation of this work is to address real-time sequential inference of parameters with a full Bayesian formulation. First, the proper generalized decomposition (PGD) is used to reduce the computational evaluation of the posterior density in the online phase. Second, Transport Map sampling is used to build a deterministic coupling between a reference measure and the posterior measure. The determination of the transport maps involves the solution of a minimization problem. As the PGD model is quasi-analytical and under a variable separation form, the use of gradient and Hessian information speeds up the minimization algorithm. Eventually, uncertainty quantification on outputs of interest of the model can be easily performed due to the global feature of the PGD solution over all coordinate domains. Numerical examples highlight the performance of the method.     

X射线干涉光刻光束线关键光学元件热-结构耦合分析

为了保证上海光源X射线干涉光刻光束线的稳定性,减小热变形对实验结果的影响,对X射线干涉光刻光束线的3个关键光学元件——偏转镜、聚焦镜和精密四刀狭缝进行热-结构耦合分析。首先,计算偏转镜、聚焦镜和精密四刀狭缝所承载的功率密度;然后,建立其有限元模型;最后,获得光学元件的温度场和热变形的结果。结果表明,偏转镜和聚焦镜采用间接水冷方式可有效抑制热变形,冷却后的最大面形误差分别为7.2μrad和9.2μrad。精密四刀狭缝未冷却时,刀片组件温度介于271.56~273.27℃,刀口热变形为0.19 mm,直线导轨热变形为0.08 mm;经过铜辫子冷却后,刀片组件温度降至22.24~23.94℃,刀口热变形降至0.2μm,直线导轨热变形降至0.1μm;采用影像法和接触探头法测试后,刀口直线度、平行度和重复精度均满足技术要求。偏转镜、聚焦镜和精密四刀狭缝的热变形通过间接水冷和铜辫子的冷却方式可以得到很大程度的抑制,进而保证光斑质量。     

Experimental optimization of power-function-shaped drive pulse for stick-slip piezo actuators

Motion of a stick-slip piezo actuator is generally controlled by the parameters related to its mechanical design and characteristics of the driving pulses applied to piezoceramic shear plates. The goal of the proposed optimization method is to find the driving pulse parameters leading to the fastest and the most reliable actuator operation. In the paper the method is tested on a rotary stick-slip piezo actuating system utilized in an atomic force microscope.The optimization is based on the measurement of the actuator response to driving pulses of different shapes and repetition frequencies at various load forces. To provide it, a computer controlled testing system generating the driving pulses, and detecting and recording the corresponding angular motion response of the actuator by a position sensitive photo detector (PSPD) in real time has been developed. To better understand and interpret the experimental results, supportive methods based on a simple analytical model and numerical simulations were used as well.In this way the shapes of the single driving pulses and values of the load force providing the biggest actuator steps were determined. Generally, the maximal steps were achieved for such a combination of the pulse shapes and load forces providing high velocities at the end of the sticking mode of the actuator motion and, at the same time, lower decelerations during the slipping mode.As for the multiple driving pulses, the pulse shapes and values of repetition frequency ensuring the sticking mode of the actuator motion during the pulse rise time together with the maximum average angular rotor velocity were specified. In this way the effective and stable operation conditions of the actuator were provided.In principle, the presented method can be applied for the testing and optimization of any linear or angular stick-slip actuator.     

KJS-Y系列矿用水动力降尘器的改进设计

针对当前KJS-Y系列降尘器效率低的问题,通过调整叶轮轴向间隙与径向间隙参数,分别对不同安装参数的降尘器进行数值模拟,通过数值模拟分析特定截面压力分布情况,确定了叶轮最佳安装参数,大大提高了降尘器的工作效率,同时降低了设计成本。     

轨道式垃圾回收机器人设计与分析

针对高速公路高峰期拥挤产生的垃圾等问题,设计一种轨道式垃圾回收机器人,由光伏发电装置、机器人壳体、末端手爪、关节臂以及控制系统等组成,主体结构采用双臂三关节结构,采用西门子PLC控制系统,通过控制关节臂的旋转以及偏转、末端手爪的旋转及开合等动作来实现工作的目的。结合外场作业的特殊性,采用光伏能源装置,对其结构及控制系统进行设计,通过对机器人进行三维建模、运动和控制仿真分析,验证系统的可行性及有效性。