大气激光通信中的光斑特性模拟和验证

根据空-地大气激光通信信道的特性,基于惠更斯-菲涅耳原理,应用夫琅禾费圆孔衍射的算法,对光波强度和光斑图像在光束截面内的分布进行分析及计算,研究了传输距离、发射孔径、激光波长以及湍流结构常数等对光斑形状及光强分布的影响。利用对数正态分布建立了大气湍流信道模型,通过对不同传输距离条件下光斑上不同点的光强分布进行计算统计和仿真分析,实验和仿真结果表明：光斑的光强分布图样服从贝塞尔分布。因此,在相同的大气湍流条件下,选择较长波长激光和较大孔径的发射器,可以有效降低光强闪烁引起的衰减,从而提高大气激光的通信质量。     

COMPUTING MAXIMUM CLIQUES OF CIRCULAR ARCS IN PARALLEL*

Given a set S of n proper circular arcs, it is required to identify a largest cardinality subset K[S] of S each two of whose members intersect. This paper describes an optimal parallel algorithm to compute K[S]. The algorithm is not based on any previously known sequential solution, and is designed for the CREW PRAM model of computation. It uses 0(n/logn) processors and runs in O(logn) time. An interesting feature of the algorithm is that it transforms the computational geometric problem at hand, to a problem involving computations on 0-1 matrices, and then transforms the latter back into a ray shooting problem in computational geometry.     

大采高采煤机挡矸装置的改进设计

分析了传统的大采高采煤机挡矸装置的结构原理、技术特点及存在的问题,提出了改进设计并进行了仿真分析。通过增加油缸数量、加强加厚顶护板、将刚性连接改为柔性连接、增设分流集流阀等手段,实现了对挡板的动态调节和支护,有效地提高了挡矸装置的可靠性和采煤机的开采效率。仿真结果表明,改进后的挡矸装置受力更均匀,挡板能承受的力更大。     

A relation between interfacial and bulk properties along the saturation curve

A liquid-vapor interface in thermal equilibrium was considered, where the pressure tensor depends upon the density (z) and the position z. The surface tension coefficient results are parametrized with the bulk compressibility, liquid-vapor density difference, and interfacial width along the saturation curve. Previous results at the triple and critical points reported by other investigators are verified. Also included is a plot of the computed results using the parametric equation and experimental data for different substances.     

An enhanced,acoustic emission-based,single-fiber-composite test

In the single-fiber-composite (SFC) test, a fiber imbedded in a matrix is loaded in tension, resulting in a fragmentation of the fiber. In the conventional version of this test, the final fiber fragmentation length distribution is used with a micro-mechanical model to determine the average fiber/matrix interfacial shear stress. In the enhanced version of this test, one also determines the applied stress at each fiber fracture, and from this, one can evaluate the strength of the fiber at short gage lengths. In our measurement system, we utilize an acoustic emission (AE) technique to detect the fiber fractures and to locate the fiber breaks and so determine both the fiber failure stresses as well as the fiber fragmentation lengths while the test is in progress. Critical to the success of this test is a broadband AE system that utilizes point-like AE sensors, procedures for evaluatingin situ, the wavespeed of the first wave arrival and signal processing techniques for determining the arrival time of this signal as precisely as possible for a broad range of wave shapes. Here we describe the application of such an enhanced SFC test procedure to investigate the failure of a Nicalon fiber in an epoxy matrix.     

双活塞杆油缸在注塑机中的新应用

采用双活塞杆油缸注射装置，开发了一种新型注塑成型机，使用效果表明：采用该装置能提高功效，降低成本，节约能源。     

65Mn钢CCT曲线及圆锯片淬火工艺

用全自动相变测定仪测定了圆锯片常用６５Ｍｎ钢的连续冷却转为曲线，研究了不同连续冷却速度下得到的组织，为合理制订圆锯片的淬火工艺提供了依据，得到了最佳淬火工艺曲线。     

一种越野轮胎的结构设计

本文介绍了285/70R17 121Q规格越野轮胎的设计。外轮廓方面:轮胎的设计外直径834 mm,充气断面宽292 mm,轮胎的行驶面宽240 mm,设计行驶面弧高度11.8 mm,胎圈着合直径取值430 mm,轮胎的胎圈着合宽度245 mm,轮胎的断面水平轴位置取值0.842 3;轮胎的胎面花纹设计分为M型和L型,2种花纹为交替变节距呈现,花纹深度13.3 mm,花纹饱和度66.26%。轮胎的施工设计方面:胎面挤出部件位全分层设计,可更好的区分胶种,功能性更强,胎侧挤出部件为双复合设计,冠带层的1#、2#带束层材料使用3×0.30 HT钢丝帘线,胎圈部位的钢丝圈为斜六角形结构,更好的保证了成品断面钢丝圈部位,切割后的近圆形;胎胚的成型使用的设备是萨驰一次法成型机,胎胚的硫化使用的设备是韩国东和液压硫化机,硫化工艺为氮气硫化。生产的成品轮胎的外缘尺寸、强度性能和耐久性能等均满足国家标准要求。     

一种雪地轮胎的结构设计

本文介绍了265/70R17115S规格雪地轮胎的设计,外轮廓方面,轮胎的设计外直径797 mm,充气断面宽282 mm,轮胎的行驶面宽207 mm,设计行驶面弧高度8.5 mm,胎圈着合直径取值430 mm,轮胎的胎圈着合宽度237.8 mm,轮胎的断面水平轴位置取值0.96746;轮胎的胎面花纹设计分为长型花纹(M型、L型)与短型花纹(S型),3种花纹为交替变节距呈现,花纹深度10.4 mm,花纹饱和度68.16%。轮胎的施工设计方面:胎面挤出部件为全分层设计,可更好的区分胶种,功能性更强,胎侧挤出部件为双复合设计,冠带层的1#、2#带束层材料使用3×0.30HT钢丝帘线,胎圈部位的钢丝圈为斜六角形结构,更好的保证了成品断面钢丝圈部位,切割后呈近圆形;胎胚成型使用的设备是萨驰一次法成型机,胎胚硫化使用的设备是韩国东和液压硫化机,硫化工艺为氮气硫化。生产的成品轮胎的外缘尺寸、强度性能和耐久性能等均满足国家标准要求。     

Insights into the Action Mechanism of the Antimicrobial Peptide Lasioglossin III

Lasioglossin III (LL-III) is a cationic antimicrobial peptide derived from the venom of the eusocial bee Lasioglossum laticeps. LL-III is extremely toxic to both Gram-positive and Gram-negative bacteria, and it exhibits antifungal as well as antitumor activity. Moreover, it shows low hemolytic activity, and it has almost no toxic effects on eukaryotic cells. However, the molecular basis of the LL-III mechanism of action is still unclear. In this study, we characterized by means of calorimetric (DSC) and spectroscopic (CD, fluorescence) techniques its interaction with liposomes composed of a mixture of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC) and 1-palmitoyl-2-oleoyl-sn-glycero-3-rac-phosphoglycerol (POPG) lipids as a model of the negatively charged membrane of pathogens. For comparison, the interaction of LL-III with the uncharged POPC liposomes was also studied. Our data showed that LL-III preferentially interacted with anionic lipids in the POPC/POPG liposomes and induces the formation of lipid domains. Furthermore, the leakage experiments showed that the peptide could permeabilize the membrane. Interestingly, our DSC results showed that the peptide-membrane interaction occurs in a non-disruptive manner, indicating an intracellular targeting mode of action for this peptide. Consistent with this hypothesis, our gel-retardation assay experiments showed that LL-III could interact with plasmid DNA, suggesting a possible intracellular target.