Flow of granules through cylindrical hopper

The gravity flow characteristics of pharmaceutically important granules were studied in a cylindrical hopper with attachable orifice disk at the bottom. Results indicate that materials property and orifice diameter play key role in determining mass flow rate while keeping environmental condition (temperature) at fixed range. A new dimensionally analyzed equation was developed to predict gravity flow of pharmaceutically important granules. The developed correlation agreed well with the experimental data. Calcium gluconate and lactose were used for preparing granules. Generally, glidant/lubricant materials are added to pharmaceutical granules during tablet manufacturing process, in order to improve physical property of granular material. Hence, the effect of glidant/lubricant on mass flow of granules through hopper was also studied. Magnesium stearate (1.5%) was added as glidant before granulation.     

液相沉淀法制备超微钴蓝颜料

研究了以硝酸铝,硝酸钴等为原料,采用液相沉淀法合成具有尖晶石型结构钴蓝颜料的制备方法。系统讨论了沉淀剂种类(氢氧化钠,氨水,尿素)、反应溶液浓度、洗涤方法、分散剂等工艺因素对合成钴蓝颜料粒度和光学性能的影响。采用SEM、TEM观察了合成颜料的形貌。最终制备出二次粒径中位径d50为670nm,一次粒径在45nm左右的超微钴蓝颜料。     

粉末涂料涂装工艺(Ⅰ)

介绍了粉末涂料的几种涂装方法及其原理、特点、应用范围和进展情况，重点介绍了静电粉末涂装方法。     

氯丁橡胶胶粘剂

1低温聚合、快速结晶型氯了用胶氯丁橡胶的结晶度与反式1，4含量有关，而反式1，4含量又是由乳液聚合温度决定的，聚合温度越低，反式1，4含量越高。为了得到快速结晶型氯丁橡胶，聚合必须在较低温度下进行，一般不高于15℃。快速结晶型氯丁橡胶广泛用于鞋底的粘接、层压板的粘合、汽车装饰，以及其它多种用途。主要从引发剂、调节剂等几个方面改进氯丁橡胶的性能：2＠基氯T橡胶。驻基氯丁胶是氯丁二烯和甲基丙烯酸的共聚物，是非结晶性，适用于室温硫化和耐热性用途。与快结晶型氯丁橡胶相比，由其配制的胶粘剂粘结强度形成更快，耐热性增…     

溶剂沉淀法制备的聚酰胺粉末之溶剂与粉末结构和热稳定性的关系

使用粒度分布仪、白度仪、电子显微镜和差热仪测定四种溶剂沉淀法制备的聚酰胺粉末发现：每种方法所获得的粉末粒径、比表面积、白度均不相同；以乙醇 氯化钙混合溶剂制备的粉末内部具有多孔结构；以乙醇 盐酸 水混合溶剂制备的粉末热稳定性较高     

细长钢管内壁涂塑工艺

采用流化床和热喷涂方法喷涂直径小于２０ｍｍ的长钢管内壁。叙述了工艺过程和涂层检测方法。     

化学法处理铜合金屑工艺的热力学和动力学分析

本文对化学法处理普通黄铜屑，直接制备纯铜粉末进行了热力学和动力学分析研究及试验表明：Zn，Fe等元素的酸浸反应容易进行，氧化及还原速度快．酸浸过程受扩散控制，其动力学方程为进一步的热力学分析指出，本工艺适合于处理各种铜合金尾料，尤其适合于黄铜类铜合金尾料。     

超细粉体微胶囊红磷阻燃剂的研制

红磷经湿法研磨预处理，在一定pH值（9．0－9．5），表面活性剂用量为0．8％－1．0％，2200Hz超声波振荡15min后，采用蜜胺树脂预聚体原位法包覆，制得了微胶囊红磷阻燃剂的超细粉体，其平均粒径为2．186um，并探讨了预处理，PH值，表面活性剂及超声波对粒度的影响。     

ADHESION OF ELASTOMERS: DWELL TIME EFFECTS

The strength of adhesion of elastomers to rigid substrates generally increases with time of contact. This effect has been studied for samples of butyl and chlorobutyl rubber adhering to some rigid substrates. The peel strength increased continuously over long periods of contact until in some cases failure became cohesive within the elastomer layer. At higher temperatures the strength increased more rapidly, consistent with the WLF relation governing molecular motions. It is postulated that slow molecular rearrangements occur at the interface and increase the bond strength. A criterion for the observed transition from interfacial to cohesive failure is suggested.     

The preparation of coupled WO3/TiO2 photocatalyst by ball milling

The coupled photocatalyst WO₃/TiO₂ is prepared by ball milling by doping WO₃ into TiO₂ and using H₂O solution as disperser. The coupled photocatalyst WO₃/TiO₂ is characterized by UV–VIS diffuse reflection spectrum, X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD) and Transmission electron microscopy (TEM). The results show that the optimum percentage of WO₃ doped is 3% and that the photocatalytic activity of the coupled WO₃/TiO₂ photocatalyst is much higher than that of TiO₂ and WO₃–TiO₂ with no ball milling. Compared with TiO₂, the photoexcited wavelength range of the WO₃/TiO₂ photocatalyst red-shifts about 50 nm, and the light absorption intensity is also improved. The crystal phase of TiO₂ is not changed and new crystal phases are not found during the process of ball milling. WO₃ and TiO₂ coupled highly, forming the WO₃/TiO₂ photocatalyst. The increased photocatalytic activity of the coupled photocatalyst may be attributed to the enhance charge separation efficiency and the extend wavelength range of photoexcitation.