脱氢型室温硫化硅橡胶的研究

考察了端羟基聚有机硅氧烷、补强填料和含氢硅油的种类对脱氢型室温硫化(RTV)硅橡胶的力学性能和粘接性能的影响,以及催化剂种类对RTV硅橡胶的凝胶时间和表观密度的影响。结果表明,当端羟基聚二甲基硅氧烷和端羟基聚甲基苯基硅氧烷按10∶3的质量比并用时,RTV硅橡胶的剪切强度较高;当侧氢基硅油和端氢基硅油按1∶1~1∶3的质量比配合使用时,能明显改善硅橡胶的剪切强度;通过选择适当的催化剂,可调整脱氢型硅橡胶的凝胶时间,制得较致密的硫化胶;二氧化钛、氧化锌对脱氢型RTV硅橡胶均有补强作用,而经甲基三乙氧基硅烷处理的氧化锌对脱氢型RTV硅橡胶的补强作用最明显。     

一步法合成(R)-α-硫辛酸

为提高(R)-α-硫辛酸(Ⅱ)合成收率,降低生产成本,以R体α-甲基苄胺拆分6,8-二氯辛酸得到的(R)-6,8-二氯辛酸(Ⅰ)为原料,在水相中采用一步法合成Ⅱ。讨论了摩尔比、反应温度、滴加时间等诸因素对产物收率及比旋光度的影响,获得了较优合成条件:拆分反应中,n(6,8-二氯辛酸)∶n〔(R)-α-甲基苄胺〕=1∶0.48,反应温度35℃,盐酸酸化;取代反应中,n(Ⅰ)∶n(二硫化钠)=1∶1.2,反应温度75℃,滴加时间3.0 h。在该优化条件下,Ⅱ的总收率为30.0%,并在该条件下,将6,8-二氯辛酸投料量扩大至600 g,Ⅰ投料量扩大至222.0 g,所得Ⅱ平均总收率可达34.3%。     

2005年国外有机硅进展

根据2005年公开发表的相关资料,对1年来国外有机硅的市场状况作了分析,重点介绍了1年来国外几大有机硅公司的动向及产品开发情况。     

LDPE／BR微孔塑料的制备和性能研究

讨论了ＬＤＰＥ／ＢＲ并用比、交联剂、发泡剂及助剂、填料和共混温度、发泡成型温度对ＬＤＰＥ／ＢＲ并用比、交联剂、发泡剂及助剂、填料和共混温度、发泡成型温度对ＬＤＰＥ／ＢＲ微孔塑料性能、结构的影响。结果表明：ＬＤＰＥ／ＢＲ（８０／２０质量比）１００份，ＤＣＰ０９份，ＡＣ３５份，复合发泡助剂３份，活性ＣａＣＯ３２５份，共混温度１１０℃，发泡成型温度１７０℃下，可制得性能优良的微孔塑料。扫描电镜、光学显微镜观察结果表明在上述条件下ＬＤＰＥ／ＢＲ胶料混合均匀，微孔塑料孔眼小、分布较均匀     

再生丁基橡胶与非极性不饱和橡胶共混物的性能研究

对再生丁基橡胶(RIIR)与非极性不饱和橡胶共混物的性能进行了研究。结果表明,RIIR易以填料的形式加入到非极性不饱和橡胶中使用,当RIIR以填料的形式加入到NR、BR及SBR中时,不仅使它们的耐热氧老化性及耐屈挠龟裂性得到明显改善,而且使NR及BR的撕裂强度及扯断伸长率提高;RIIR作为生胶与BR及NR共混,可改善BR的耐热氧老化性,提高NR的撕裂强度;SBR与RIIR共混,均使拉伸强度及撕裂强度降低;非极性不饱和二烯类橡胶与RIIR共混后,均使耐磨性降低。     

国产子午线轮胎专用天然橡胶应用试验

通过对国产子午线轮胎专用天然橡胶的化学分析、物理性能检验和进行胎面胶、胎体胶的小配合、大配合胶料试验，并与进口天然橡胶试验结果进行对比，研制了一批用国产子午线轮胎专用天然橡胶生产的９．００Ｒ２０全钢子午线轮胎作里程试验。试验结果表明，国产专用天然橡胶只要适当降低塑性初值（Ｐ＿０）和生胶门尼粘度，按国际通用标准进行包装，完全可以代替马来西亚标准橡胶（ＳＭＲ１０和ＳＭＲ２０）用于子午线轮胎生产中。     

Phase Separation in Gelling Silica–Organic Polymer Solution: Systems Containing Poly(sodium styrenesulfonate)

Phase separation which occurs in parallel to the hydrolysis and gelation of alkoxysilane solution containing poly(sodium styrenesulfonate) (NaPSS) has been investigated. Depending on the reaction conditions, gel morphologies such as isolated pores, particle aggregates, and interconnected continuous pores from 0.1 to 100 μm long have been observed. Time-resolved light scattering of gelling solution suggested the occurrence of spinodal phase separation through the polymerization of silica and the subsequent freezing of the developing structure by sol-gel transition. The effects of reaction parameters on the periodic size are explained mainly in terms of their influence on the "chemical cooling" rate which is determined by the polymerizatica rate of silica and the solubility of NaPSS in the reacting solution.     

硅粉加入量对刚玉-氮化硅复合材料力学性能的影响

以刚玉、氮化硅、粘土和硅粉为主要原料,在空气气氛下于1550℃保温3h烧成制得刚玉-氮化硅复合材料,研究了硅粉加入量(w)分别为0、4%、8%、12%时对试样常温物理性能、高温抗折强度的影响,并采用XRD、SEM、EDS等手段分析了试样的物相组成和显微结构。结果表明:在硅粉加入量<8%时,Si主要填充在烧成制品基质的空隙中;随着硅粉加入量的增加,制品致密化程度提高,常温强度增大,同时由于硅粉原位生成了纤维状赛隆而使制品的高温强度增大;但在硅粉加入量>8%时,Si可能构成连续相,又导致制品致密度下降和高温力学性能恶化。     

Investigation of conductivity characteristics of nitrile butadiene rubber vulcanizates filled with semiconducting carbide ceramic

SiC‐ and B₄C‐filled NBR rubber composites were prepared with various volume fractions of filler by a conventional roll‐mill method. The morphological structures of the NBR–SiC and NBR–B₄C composites were analyzed by scanning electron microscopy. The dependence of room‐temperature volume resistivity (ρ_v) on the concentration of filler in the two systems was studied. In addition, variation in the number of current carriers (n), mobility carriers (μ), dielectric constant (ε), and dielectric loss factor (tan δ) on filler concentration in the two systems were investigated in detail. The applicability of composites as negative temperature coefficient (NTCR) linear thermistors was studied by the dependence of volume resistivity on temperature. The resistivity showed negative temperature dependence and changed linearly with temperature parallel. The conduction mechanism of the conductivity of the two composites was analyzed in terms of the computed activation energy and hopping energy. Change in volume resistivity as a function of frequency for the two systems was also investigated. Finally, the dependence of volume resistivity on applied pressure and possible real applications of these composites as transducers in pressure sensors were also studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2158–2165, 2007     

复合材料POSS/TX-10/Bent的制备及其吸附性能

以多面齐聚倍半硅氧烷(POSS)、TX-10型非离子表面活性剂为改性剂对膨润土(Bent)进行复合改性制备了复合材料(POSS/TX-10/Bent),并利用亚甲基蓝研究了其吸附性能。采用XRD、XPS、EA、FTIR、SEM对POSS/TX-10/Bent进行了组成与结构表征。结果表明,POSS和TX-10型非离子表面活性剂都成功插入到膨润土层间,使得复合材料层间距增大,疏水性增强。吸附实验表明,在30℃、pH为6.52(原始值)的条件下,复合材料投加量5 g/L、吸附180 min时效果最佳。在同等吸附条件下,复合改性膨润土对亚甲基蓝的吸附能力远大于未改性的膨润土。吸附过程更符合准二级动力学模型,平衡吸附数据与Langmuir等温吸附曲线吻合较好,吸附是一个自发的吸热过程,POSS/TX-10/Bent对亚甲基蓝的理论最大吸附量为253.81 mg/g。