CVD金刚石工具膜生长特征SEM观察

本文用不热形变栅状直丝化学气相沉积（ＣＶＤ）法生长金刚石膜，在Ｓｉ及ＷＣ－Ｃｏ硬质合金衬底上金刚石膜晶面显露规律随衬底温度和甲烷浓度而异，经适当表面处理及选择合适的工艺条件，当生长初期衬底上就呈现出良好晶形的沉积膜，衬底与膜之间的粘结力能得到提高。Ｒａｍａｎ谱分析表明此膜仅具有特征金刚石１３３２ｃｍ￣（－１）峰，通过ＳＥＭ观察揭示出盒刚石膜可在表面、侧面及棱上生长，并与衬底有良好的联结。     

电荷耦合图像传感器在细线直径测控系统中的应用

文中给出了一个以氟化氪固体激光器做光源，以电荷耦合图像传感器为光屏，应用夫朗禾费衍射原理，实现对细丝直径在线检测自动控制。该方案对相关企业质量控制的自动化是有意义的。     

一种微通道换热器的设计与分析(英文)

设计了一种用来测试微通道换热性能的实验装置。该系统由微通道换热器、模拟热源、微型水泵、连通管、测试三通及其它测试元件构成。通过检测温度、压力和流量等参数能够得到微通道的传热和摩阻参数。针对该实验装置,对微通道中流体的压降和传热分别进行分析和研究。实验表明,当微通道水力直径为381μm时,宏观理论公式已不适用于微通道摩阻及其换热的计算。此时,微通道的摩阻比宏观理论计算值小31.6%～41.9%;微通道结构具有良好的换热性能,其Nu可达9.2。     

微机控制缠绕机控制系统的数字仿真监测

本文采用控制系统的数字仿真技术，在ＳＴＤ工业控制机上实现了对微机控制纤维缠绕机控制系统的稳速精度、跟踪性能和光电编码器的性能的监测。文中阐述了检测电路、测量方案、仿真程序设计和结果分析等内容。     

1等标准光滑圆柱环规检测装置

本装置是在具有高精度导轨的SIP三坐标测量机上架设激光干涉仪作为测量标准器，利用电感测微仪作为瞄准器，使测量可以直接溯源到激光波长，实现了1等标准光滑圆柱环规的高精度测量。装置对φ50mm标准环规直径测量的不确定度达到70．15μm。通过与瑞士国家计量局和国家计量院的比对测量证实，无论在国内还是国际环规测量方面，该装置已达到先进水平。     

二阶曲线渐近线的等价定义及其应用

给出了射影几何中关于二阶曲线渐近线的几个等价定义,并探讨了根据不同 定义的二阶曲线渐近线的应用．     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Synthesis of polyurethane resins and its improvement on dimensional stability and finishing performances of medium‐ and small‐diameter softwoods

This study analyzed the effects of polyurethane (PU) resin treatments on surface homogeneity, dimensional stability, and finishing performances of medium‐ and small‐diameter softwoods produced in Taiwan. Two‐pack PU resins were prepared by combing short castor oil‐modified alkyd resin serving as a polyol with polymeric 4,4′‐diphenymethane diisocyanate (PMDI) serving as a hardener, by the molar ratio of NCO/OH+COOH of 1.2. Four types of short oil‐modified alkyd resins with different polyhydric alcohols (glycerin and pentaerythritol) and polybasic acids (phthalic anhydride and isophthalic acid) were synthesized. Three kinds of medium‐ and small‐diameter softwoods, including China fir, Taiwanina, and Japanese fir with a diameter of 10–15 cm were obtained from Hui‐Sun Forest Station, Taiwan. The wood coating of nitrocellulose (NC) lacquer including sanding sealer and top clear was used. Results show that the surface hardness, homogeneity, moisture excluding efficiency, and antiswelling efficiency of woods were enhanced by PU resin treatments. Among all the PU resins, the isophthalic acid and pentaerythritol‐containing PU resin (IPA‐P‐MDI) achieved the best improved efficiency on dimensional stability of woods. Results of two types of finishing procedure, i.e. NC lacquer sanding sealer plus top clear and top clear only, applied onto the PU‐treated woods revealed that the hardness, adhesion, and durability of NC lacquer films on the PU‐treated wood were superior to those of untreated one, especially for top clear finishing alone. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

S28-248型偏心BDC钻头的研制与应用

为了提高中原油田沙3中至沙4段四开小井眼的钻井速度,有效地解决易卡钻、钻速低、成本高以及小间隙井眼固井质量差等问题,中原油田与川石·克里斯坦森金刚石钻头有限公司合作,研制开发了用于深部小井眼钻井的149.2mm的S28-248型偏心BDC钻头。详细介绍了该钻头的设计特点及现场应用情况。     

蒸发冷凝法中气体压强和蒸发温度对粒子大小的影响

在Ｎ＿２气氛中，用蒸发冷凝法，制备了Ｓｎ细微粒和Ｆｅ及Ｆｅ－４７（ｗｔ）％Ｎｉ合金超细微粒。分别用ＳＥＭ和ＴＥＭ，直接观测粒子大小及其分布。结果表明，平均粒径不是随Ｎ＿２气压强增加单调上升，而是在某一压强Ｐ＿（ｍａｘ）下，出现最大值。随蒸发温度提高，Ｐ＿（ｍａｘ）值迅速增大。粒子大小及其分布与粒子生长机制密切相关。对粒子凝聚生长条件进行了简要讨论。