Extended preservation of raw beef and pork meat by hyperbaric storage at room temperature

Hyperbaric storage (HS) was evaluated as a new food preservation methodology at room temperature (RT) for beef and pork meat, both minced and in pieces, and compared to refrigeration (RF) storage. The meat samples were stored at 50, 75 and 100 MPa and variable RT up to 60 days. HS at 75 and 100 MPa could not only inhibit microbial growth but also inactivate microorganisms. Regarding physicochemical analyses, an overall equal to better pH maintenance in HS samples was achieved, and similar colour differences between HS and RF were observed. Generally, similarities in moisture content and drip loss between HS (mostly 75 and 100 MPa) and RF were detected (tendency for lower values in the former and higher values in the latter for the higher pressure level). Protein solubility revealed a decrease of sarcoplasmic protein values during storage with a pressure level dependency in some samples.     

-15℃下Na+， K+， Mg2+//Cl-， NO3-， SO42——H2O体系相平衡研究

新疆卤水硝酸盐矿主要含有Na⁺、K⁺、Mg²⁺、Cl^-、NO₃^-、SO₄^2-六种离子，属于高元复杂体系，其合理利用和开发需要不同温度下的相平衡研究作为理论支撑。采用等温溶解平衡法，对Na⁺， K⁺， Mg²⁺//Cl^-， NO₃^-， SO₄^2--H₂O体系在-15℃、NaCl·2H₂O饱和条件下的相平衡进行了研究，并构建了相图。相图中有六个零变量点和八个两盐结晶区，只存在一种复盐KCl·MgCl₂·6H₂O。八个两盐结晶区，分别对应于NaCl·2H₂O+Na₂SO₄·10H₂O、NaCl·2H₂O+NaNO₃、NaCl·2H₂O+KCl、NaCl·2H₂O+KNO₃、NaCl·2H₂O+MgSO₄·7H₂O、NaCl·2H₂O+MgCl₂·8H₂O、NaCl·2H₂O+Mg(NO₃)₂·6H₂O和NaCl·2H₂O+KCl·MgCl₂·6H₂O，其中NaCl·2H₂O+Na₂SO₄·10H₂O共晶区最大，在低温时，硫酸钠的溶解度最小，降温过程中较易结晶析出。与该体系在25℃下的相图相比，复盐种类减少5种，零变量点减少19个，相关系得以极大简化。     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

GK1C型内燃机车频繁停车现象探讨与解决方案

运用过程中各类相关因子的变化,会使得机车柴油机配气相位出现一定程度变化,采取某种措施调整或是处理可以解决动力不足的问题。     

一种汽车顶盖抗雪压动态仿真分析方法

目前顶盖雪压静态仿真分析方法的雪压计算值与测试值存在偏差,并且不能反映顶盖实际变形的位置和整体变形模式。为改进静态仿真分析方法,提出一种非线性显式计算的动态仿真分析方法,并以某乘用车为例,通过试验验证了其可靠性及有效性,为顶盖的研发设计提供了参考。     

前和煤业东胶带运输大巷钻孔卸压围岩控制技术

为有效解决前和煤业3#煤层东胶带大巷在原有锚网索支护下围岩变形量大的问题,结合巷道变形特征,确定采用钻孔卸压技术,采用理论分析和数值模拟的方式确定卸压钻孔在修巷作业前,垂直于巷帮打设,钻孔深度为8 m,结合巷道的具体条件确定巷道采用卸压钻孔+让压支护的围岩控制方案,并采用矿压监测验证支护效果。结果表明:支护方案实施后,顶底板和两帮的最大移近量分别为141 mm和132 mm,有效解决了巷道两帮及底板鼓起量大的问题,保证了巷道围岩的稳定性。     

底板带压开采工作面并行电透视探测技术应用研究

汾西矿务局水峪矿部分工作面现已面临带压开采问题，受下伏奥陶系灰岩水害影响，工作面安全回采过程中的防治水工作难度增加，尤其是带压开采工作面底板灰岩水的有效探测变得异常紧迫与重要。为了解决底板带压开采工作面富水区的探测问题，水峪矿引入了并行电透视技术，并对相应工作面进行了探测应用。并行电透视技术相对于传统音频电透视技术具有仪器智能化控制发射接收切换、一发射点并行对应多接收点、仪器智能快速高效跑极施工的3项技术优势，可体现应用现场施工高效、实际探测效果可靠的技术特点。经过对并行电透视技术及探测应用效果分析研究，证明该方法技术领先，现场施工高效，实际探测结果可靠，实用性强。     

Preparation of ZrC/SiC porous self-supporting monoliths via sol-gel process using polyethylene glycol as phase separation inducer

We present a straightforward method via sol-gel process using polyethylene glycol (PEG) as phase separation inducer to prepare zirconium carbide/silicon carbide (ZrC/SiC) porous monoliths. Organic/inorganic hybrid gels are prepared using zirconium oxychloride, furfuryl alcohol, and tetraethyl orthosilicate as major starting materials. In the presence of PEG, crack-free hybrid monoliths are obtained by drying the wet gels under ambient pressure, whereas in the absence of PEG, the wet gels break into pieces as expected. PEG plays a key role in maintaining the macroscopic shape of the monoliths. After ceramization at 1300–1500?°C, ZrC/SiC porous monoliths are obtained. SEM and mercury intrusion porosimetry data show that PEG also has strong influence on the microstructures of the monoliths. The compressive strengths of the ceramic monoliths are in the range of 0.3 to 0.7?MPa. And their compressive behavior starts to differ due to the changes in their microstructures, especially the pore structure.     

A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.     

气压仪器检定装置的升级改造

文章针对气压检定装置在使用中存在的一些问题,会同厂家对其进行了升级改造。介绍了改造后的气压检定装置的设计原理、软件和硬件设计以及技术指标等,新装置集成了目前先进的计量设备及技术,编写相应的程序软件升级改造而成。可广泛适用于气象部门空盒气压表、自动站气压传感器以及部分数字压力计的计量检定工作,实现气压检定工作的自动化,提高检定数据的准确性和可靠性,并有效提高检定的工作效率。