水溶液全循环法尿素装置中压分解"三种工艺"的比较

以生产数据结合理论计算的方法系统地比较、分析了水溶液全循环法尿素装置中中压分解“三种工艺”的热能利用、甲铵分解率、总氨蒸出率、水平衡量、一分加热器生产能力等方面的情况，提出应用和配置预分离-预蒸馏工艺的方法，评论该工艺在水溶液全循环法中的地位和作用。     

Phosphorus‐containing polyaryloxydiphenylsilanes with high flame retardance arising from a phosphorus–silicon synergistic effect

Polyaryloxydiphenylsilanes were prepared from phosphorus‐containing diols and diphenydichlorolsilane through solution polymerization. With a stoichiometric imbalance in feed monomers, the resulting polymers exhibited moderate melting points and good processing properties. The polymers prepared showed initial decomposition temperatures above 340 °C, excellent thermal stability, high char yields at 850 °C and very high limited oxygen index values of 56–59. The polymers' char yields and their (P + Si) contents showed linear relationships. © 2003 Society of Chemical Industry     

Thermodynamic and Transport Properties of Liquid HFC-227ea

The thermal conductivity and heat capacity of liquid 1,1,1,2,3,3,3-hepta-fluoropropane (HFC-227ea) have been studied by a high-frequency thermal-wave method over the temperature range of 294 to 345 K at pressures up to 2.8 MPa. The purity of the samples used throughout the measurements is 99.99 mol%. The experimental uncertainties of the thermal conductivity and heat capacity measurements were estimated to be within ±1.5 and ±2%, respectively. The thermal conductivity of HFC-227ea in the liquid phase decreases as temperature increases, while the pressure has an opposite effect.     

渣油热反应通用动力学参数测定

利用升降温度快、控温平稳的特制重油热反应评价装置,在400～500℃温度范围内,对大庆、胜利、华北、中原、管输及沙特轻质六种原油的减压渣油进行了热反应试验.气相色谱分析裂化气的组成,液相反应产物通过色谱模拟实沸点蒸馏分析,以30℃的馏程间隔划分成窄馏分,利用索式抽提对残渣油的缩合产物进行分析.通过建立的模型和编制的模型软件,得到了上述六种渣油的通用热反应模型参数.相关系数R'检验和F检验结果表明,关联出的模型常数具有较好的相关性,置信度在99%以上.偏差分析表明拟合结果与实验数据吻合较好.     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

高温超导电缆终端恒温器热负荷的计算与测定

电力电缆已被确认为高温超导技术产业化的重要项目之一。高温超导电缆终端是运行在低温的超导电缆芯向常温的高压母线过渡和致冷剂进出口的汇集组件,具有很高的技术含量。简单地介绍高温超导电缆终端恒温器的结构和功能,主要讨论终端恒温器热负荷的理论计算方法,并与试验测定进行比较。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

激光抛光技术的发展与展望

介绍激光抛光技术的发展历史,阐明激光抛光的应用现状及未来的发展前景,论述了激光抛光的工艺特点和作用机理,将激光抛光技术与其它抛光技术进行了全面的对比,指出激光抛光的优势及其存在的问题。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。