AZ31镁合金初始动态再结晶的临界条件研究

为确定AZ31镁合金初始动态再结晶的临界条件或临界应变，通过在变形温度范围473～623K、应变速率范围0．001-1 s^-1条件下进行等温压缩试验，利用所得数据并采用单参数方法，建立起AZ31镁合金初始动态再结晶的临界条件，即临界应变（εc）与变形条件（引入温度补偿应变速率因子即Zener-Hollomon参数）的定量关系，并对不同应变下合金微观组织的演变规律进行了研究。     

镁合金与钛合金的瞬间液相扩散焊

为实现镁合金AZ31B与钛合金Ti6A14V的可靠连接，研究了两者以Al为中间层的瞬间液相扩散焊接头的微观结构与连接强度。研究结果表明：当焊接时间为180min时，焊接温度是影响界面反应热力学与动力学的主要参数，其对接头的微观组织、接头界面新生相构成与连接强度有重要影响。保温温度低于450℃时，AZ3IB／AI界面无液相产生，无法实现AZ31B与Ti6A14V的可靠连接；保温温度在450℃～480℃变化时，温度对AZ31B／Al／Ti6A14V界面反应的动力学因素有明显影响，且直接决定了焊后接头新生相的构成与分布。470℃保温180min的接头剪切强度较高（72．4MPa），达到AZ31B母材（86MPa）的84．2％。     

镁合金焊接接头的力学性能

随着镬合金应用的日益广泛，其焊接接头的力学性能也受到人们的重视。介绍和分析了采用不同焊接方法时焊接接头的力学性能。并提出一些看法，对镬合金焊接接头力学性能的研究有一定促进作用。     

快速凝固Mg94.6Zn4.8Y0.6镁合金薄带的组织与性能

采用单辊快速凝固技术制备了Mg94.6Zn4.8Y0.6合金薄带,研究了薄带的组织及性能特征。结果表明:Mg94.6Zn4.8Y0.6镁合金快速凝固薄带组织由过饱和的单相-αMg固溶体组成,沿厚度方向分为两个晶区:近辊面粗大等轴晶区和自由面细小等轴晶区。Mg94.6Zn4.8Y0.6合金快速凝固薄带的显微硬度为85.95HV,在250℃左右保温2 h的显微硬度最高,超过该温度(250~300℃)显微硬度显著下降。     

硅钙合金对AM60镁合金流动性的影响

研究了硅钙合金对AM60合金流动性的影响,结果表明:硅钙合金能改善合金的铸造性能,降低合金的结晶温度间隔,提高合金的流动性,当加入1.8%的硅钙合金时,合金的流动性提高了51.7%;加入硅钙合金后,合金中形成了稳定性较高的Mg2Si颗粒,显著细化了合金的显微组织,第二相也逐渐趋于弥散分布.     

镁合金表面热喷铝工艺及防腐性研究

简述了在镁合金上的热喷铝工艺，并对表面喷铝层的耐腐蚀性进行了分析研究。对腐蚀后的表面进行了形貌观察及成分分析。结果表明，经热喷铝处理后，镁合金的耐腐蚀性能得到了极大的提高。     

Effect of temperature on mechanical behavior of AZ31 magnesium alloy

Strain rate sensitivity and tension/compression asymmetry of AZ31 magnesium alloy at different temperatures and strainrates were investigated.Both of mechanical behaviors are temperature dependent.Strain rate sensitivity increases with increasingtemperature.Thermally activated slip is the source of strain rate sensitivity.At the temperature below or near 373 K,strain ratesensitivity is very little.Tension/compression asymmetry in yielding decreases with increasing temperature.Twinning is the reasonof tension/compression asymmetry.At the temperature above or near 573 K,the material shows little tension/compressionasymmetry of the flow stress.     

半固态镁合金流变成形技术及装备

研究了镁合金半固态流变成形技术及装备，结果表明，多功能螺纹元件组合的双螺杆制浆装置制备的浆料晶粒细小（10～50μm)，固相率可在5%～50%范围内调整，封闭式加热保温，快开快关控制的浆料存储与输送装置，较好地解决了浆料连续制备与间歇压铸的配套；生产的半固态压铸件，强度提高了20%以上。     

Thermodynamic database of the phase diagrams in the Mg-Al-Zn-Y-Ce system

The Mg-Al-Zn-Y-Ce system is one of the key systems for designing high-strength Mg alloys. The purpose of the present article is to develop a thermodynamic database for the Mg-Al-Zn-Y-Ce multicomponent system to design Mg alloys using the calculation of phase diagrams （CALPHAD） method, where the Gibbs energies of solution phases such as liquid, fcc, bcc, and hcp phases were described by the subregular solution model, whereas those of all the compounds were described by the sublattice model. The thermodynamic parameters describing Gibbs energies of the different phases in this database were evaluated by fitting the experimental data for phase equilibria and thermodynamic properties. On the basis of this database, a lot of information concerning stable and metastable phase equilibria of isothermal and vertical sections, molar fractions of constituent phases, the liquidus projection, etc., can be predicted. This database is expected to play an important role in the design of Mg alloys.