浅议铝箔项目的给排水设计

通过铝箔项目的工程实例,详细介绍了铝箔项目给排水专业设计的主要构成,并总结了几点设计体会,可供有关专业设计人员借鉴、参考。     

升深2-17井络合铝聚合物充气钻井液现场试验

为加快徐加固子深层天然气的勘探开发步伐，缩短深层气井的建井周期，在升深2-17井进行了充气钻井试验。介绍了络合铝聚合物充气钻井液技术的现场应用概况及效果以及井漏的发生与处理过程、钻井液起泡的解决措施。在现场试验过程中，络合铝聚合物钻井液性能稳定，具有较强的抑制性和较好的流变性能，流性指数控制在0．7左右，具有良好的携屑和稳定井壁能力，而且粘度较低，基本上控制在33～52s之间，满足了现场充气和脱气的需要；该钻井液抗温可达180℃，润滑性能较好，在钻井过程中无粘卡显示，在深井欠平衡井眼稳定方面取得了较好的效果；在不同的气液比条件下，可以在0．83～1．08g／cm。之间实现对当量密度的调节;与常规钻井工艺相比，充气钻井可以使机械钻速提高30％～50％；在钻进过程中实现了充气和点火同时进行，达到了欠平衡钻井工艺技术的要求，为进一步开展气体钻井打下了良好的基础。     

Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.     

ICP-AES法测定硅铝钡合金中的钡

介绍ICP—AES法测定硅铝钡中的钡的分析方法，用氢氟酸一硝酸一高氯酸混合酸溶解试样，用钡的233．527nm谱线测定钡．该方法简便快速，精密度好，准确度高，加标试验回收率为99％～100％，相对标准偏差为0．25％～0．56％．     

Repair of Cracked Aluminum Overhead Sign Structures with Glass Fiber Reinforced Polymer Composites

Transportation departments have been using aluminum overhead sign structures since the 1950s. It is well documented that cracks develop in the welds between diagonal and chord members due to fatigue stresses from wind-induced vibration of the slender members. The cracks propagate to complete failure of the members, which can cause collapse of the truss and inflict injuries. The original design of overhead sign structures did not consider fatigue as a limit state. In addition, field welding of aluminum structures for any possible repairs is prohibited. A repair method for the cracked aluminum welded connections between diagonals and chord members using glass fiber reinforced polymer composites (GFRPs) is proposed. The static load carrying capacity of the welded connection, and the cracked connection repaired with GFRP composites are established. The paper describes the surface preparation of the aluminum tubular members, and the architecture and application sequence of the GFRP composite to retrofit the connection. Experimental results are presented from static tests of welded aluminum connections, welded aluminum connections retrofitted with GFRP composites, and new aluminum connections that depend only on GFRP composite elements for their strength. The results from monotonic static tests carried out on cracked welded specimens from actual sign structures show that the retrofitted connection with GFRP reinforcement achieved 1.17 to 1.25 times the capacity of the welded aluminum connection without any visible cracks. This result, and the minimal traffic disruption anticipated in the actual field application, makes this retrofit method a good candidate for implementation.     

利用Pd—20%Ag合金钎焊单晶钼

利用Ｐｄ－２０％Ａｇ合金钎焊单晶钼，评价了钎焊点的室温弯曲性能，检验了钎焊怪的显微组织，硬度和化学成分。     

铝对W9Mo3Cr4V高速钢组织和硬度的影响

用Ｘ－射线仪，扫描电镜和透射电镜系统研究了铝对钨钼系高速钢铸态，退火以及淬回火组织的影响，铝含量超过２．０％，淬火组织中出现含析出合金的铁素体组织和晶界屈氏体，导致钢硬的降低。     

燃煤MHD发电Cr25Al5电极材料的腐蚀行为研究

采用Ｃｒ＿（２５）Ａｌ＿５合金进行煤渣／种子条件下静态腐蚀试验（温度１３７３－１５７３ｋ，时间５０－１５０ｈｒ），试验后得出三种温度下腐蚀重量变化与腐蚀时间的关系，并借助金相显微镜、扫描电镜和俄歇分析进行有关形貌及成份分析，试验表明，温度是材料腐蚀的主要因素，在１４７３ｋ条件下材料的抗蚀性最好，Ａｌ、Ｓｉ元素在腐蚀过渡层中富集，Ｃｒ元素变化不大，但有从基体向外扩散的趋势。由此，这一材料若能进一步改进，可望在控制壁面温度的半热壁型通道中进行试验研究。     

添加剂及硫元素对ZL108合金中铁相形态的影响

在含铁为１２％的ＺＬ１０８合金中，加入５％的以锰、铬、稀土为基本成分的添加剂时，合金中针状、片状的铁相变为团球状、块状及梅花状。单独加硫时，铁相呈短杆状。先加入３％的添加剂再加硫，则铁相变为非常细小的团球状、块状，根据ＧＢ３５０８－８３的规定，铁相形态可达一级