Mechanism and prediction of failure of diamond films deposited on various substrates by HFCVD

Diamond films were deposited on the WC-Co cemented carbide and Si3N4 ceramic cutting tool substrates by hot-filament-assisted chemical vapour deposition. The adherence property of diamond films was estimated using the critical load (Pcr) in the indentation test. The adhesive strength of diamond films is related to the intermediate layer between the film and the substrate. Poor adhesion of diamond films to polished cemented carbide substrate is owing to the formation of graphite phase in the interface. The adhesion of diamond films deposited on acid etched cemented carbide substrate is improved, and the peeling-off of the films often happens in the loosen layer of WC particles where the cobalt element is nearly removed. The diamond films' adhesion to cemented carbide substrate whose surface layer is decarbonizated is strengthened dramatically because WC phase forms by reaction between the deposited carbon and tungsten in the surface layer of substrates during the deposition of diamond, which results in chemical combination in the film-substrate interface. The adhesion of diamond films to silicon nitride substrate is the firmest due to the formation of chemical combination of the SiC intermediate layer in the interfaces. In the piston-turning application, the diamond-coated Si3N4 ceramic and the cemented carbide cutting tools usually fail in the form of collapsing of edge and cracking or flaking respectively. They have no built-up edge(BUE) as long as coating is intact.As it wears through, BUE develops and the cutting force on it increases 1 - 3 times than that prior to failure. This can predict the failure of diamond-coated cutting tools.     

D杯形砂轮修整碟形金刚石砂轮试验研究

本文采用了D杯形砂轮与碟形砂轮对磨法来修整大直径树脂结合剂碟形金刚石砂轮。在分析研究杯形砂轮修整碟形砂轮的修整原理及修整方式的基础上，用自行研制的专用修整装置，从主轴转速、修整深度、修整工具结合剂类型等方面进行了对比工艺试验研究，总结了杯形砂轮修整碟形砂轮的不同工艺参数与修整效率、修整质量之间的工艺规律。试验结果表明，在本试验条件下主轴转速500r／min，修整深度0．02mm的修整效率较好；细粒度、中等浓度的青铜结合剂杯形金刚石砂轮与粗粒度、高浓度的杯形砂轮修整碟形砂轮相比，后者具有较好的修形效果和修整效率；D杯形砂轮与GC杯形砂轮交替配合使用可以大大提高碟形金刚石砂轮的修形效率和修锐效果。     

基底材料和温度对CVD金刚石沉积的影响

使用热丝CVD装置在钢渗铬层、三氧化二铝、YG8硬质合盒基底上沉积了金刚石膜、结果表明，在700～900℃温度范围内，热稳定性好的基底材料有利于金刚石晶核的形成。硬质合金和三氧化二铝的热稳定性都比钢港铬层好，在700～900℃能获得10^7cm^-2以上的形核密度，而钢渗铬层超过800℃后．形核密度低于10^6cm^-2。     

大面积PCD复合片电火花加工高效节能脉冲电源的研究

本文通过对大面积PCD复合片材料物理特性的分析及电火花放电加工PCD表面放电机理的研究，分析了电火花加工大面积PCD复合片时影响加工速度及表面质量的重要因素。提出了用于加工大面积PCD复合片的理想电源模型，其特点为：大能量、高峰值电压、高峰值电流、窄脉冲、等脉冲能量输出。根据理想电源模型开发出一种高效、节能、环保型大面积PCD复合片电火花专用脉冲电源。与普通电火花脉冲电源比较，该电源加工效率高、加工表面质量好，电能利用率高，是大面积PCD复合片电火花加工的有效工具。     

微/纳米复合多层金刚石自支撑膜的制备及应力研究

利用大功率DC Arc Plasma Jet CVD装置,采用Ar-H2-CH4混合气体为气源,通过优化工艺参数,在多晶钼衬底上制备出了多层复合金刚石自支撑膜.利用扫描电镜(SEM)、X射线衍射(XRD)、激光拉曼谱(Raman)对膜体进行表征,结果显示,多层膜体的组织结构体现了微米金刚石与纳米金刚石的典型特征;复合金刚石自支撑膜具有光滑的表面,微米层与纳米层间呈相互嵌套式的界面;此外,利用激光拉曼谱分析了多层膜中的内应力状态,研究发现,多层膜中各层膜体具有不同的内应力状态,内应力沿膜体生长方向有明显变化,呈现出从压应力到拉应力的变化过程.     

磨PCD刀具陶瓷结合剂金刚石砂轮的研究

本文研究制备Na2O-B203-Si02-Al203多元系基玻璃料,并配制成低温陶瓷结合剂,研究发现:耐火度为685℃,流动性为110%～130%,线膨胀系数为5.35×10-6℃-1的低温陶瓷结合剂具有优异的性能.制备的陶瓷结合剂金刚石砂轮在725℃烧成后,磨具的抗弯强度和洛氏硬度达到最佳值,分别58.61 MPa和77.9.用其磨削PCD刀片时锋利性好,磨削中间不需修整,砂轮耐用度高.运用扫描电子显微镜(SEM)分析了陶瓷结合剂金刚石磨具的断面形貌、磨削后磨削面形貌,表明结合剂对磨粒黏结牢固,断面组织均匀.     

稀土对切玻璃金刚石锯片切削性能的影响

金刚石圆锯片可以用于切割玻璃和水晶制品。为了提高切割玻璃金刚石圆锯片的切割寿命和玻璃的切割质量．对切割玻璃金刚石圆锯片的胎体成分进行了优化设计，并在胎体材料中加入稀土化合物La2O3，同时对金刚石表面实施镀钛。本文从胎体材料对金刚石的把持力系数、实际切割的金刚石的脱落度以及锯片的切割速度方面，研究了稀土化合物在金刚石刀头胎体中的作用。结果表明：在胎体金属粉中加入适量的稀土化合物，胎体对金刚石的把持力系数有所改善，同时，增加了刀头胎体材料的脆性，实现了金刚石与胎体的同步磨损，金刚石的脱落度明显减小；切割速度比参比片提高了21．6％。     

钎焊金刚石砂轮磨削石材中金刚石粒度对磨削力的影响研究

本文通过测量不同金刚石粒度的高频感应钎焊金刚石砂轮磨削花岗石过程中的磨削力，对砂轮所受的法向力和切向力进行了研究。对不同粒度条件下磨削深度、进给速度和砂轮线速度对磨削力的影响进行了分析。研究发现磨削力随砂轮线速度的增大而减小，随磨削深度和进给速度的增大而增大，磨削深度对磨削力的影响程度比进给速度大。小粒度金刚石磨削时，磨削三要素对磨削力的影响比大粒度金刚石磨削时大。     

电铸金刚石-镍复合膜微观应力分析

用电铸方法，采用低应力电镀液，研制出了金刚石-金属复合膜。该复合膜的厚度为20-45μm，可用于制作超薄切割刀具。介绍了用X射线衍射法（xRD）测量多晶体微观应力的基本原理和用X射线衍射法测量镍多晶体显微应变的程序。用单波法计算了电铸金刚石-镍复合膜的显微应变，并用扫描电镜（SEM）观察了该复合膜的表面形貌。结果发现：阴极电流密度严重影响复合膜的显微应变，在实验所用电流密度范围内（0．6-3．5A／dm^2），随着电流密度的增加，显微应变减小。     

Processing and microstructure of investment casting turbine blade NITAC in-situ composites

Directional solidification was used to produce turbine blades by the Bridgman method. NITAC alloys with various carbon contents were investigated; the optimum range was found to be 0.40 to 0.48%. Within this range, except for the blade locking piece edges, the blade structure consisted predominantly of aligned eutectics. The in- situ eutectics were aligned tantalum fibers embedded in a γ- phase matrix. The blades were produced using an alloy displacement rate of 1.86 x 10 ^{- 6} m/s. Measurements of fiber spacings along the blade height indicated that the rate of displacement of the solidification front exhibited some variations. These variations were closely associated with dimensional changes in the turbine blade cross sections.