Simplification of the Plasma Load of Negative-Pulse-Bias Source Used in Arc Ion Plating

Based on the voltage and current fluctuating phenomenon in the arc plasma load under the negative-pulse-bias, usingthe plasma physics theory and analysis of computer simulation expatiates that the nature of plasma load in vacuumarc plasma is a capacitance     

不锈钢管道坡口加工的新方法

对于不锈钢管及合金钢管坡口的加工,采用以往的加工方法切割出来的坡口一般参差不平、比较粗糙,难于打磨平整。使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段,改善了不锈钢管及合金钢管的坡口加工效果,使加工出来的坡口像碳钢管一样平整,更加容易打磨组焊。文章介绍了这一新方法所用的设备、材料、切割原理以及操作过程。     

Improving narrow bandgap a-SiGe:H alloys grown by hot-wire chemical vapor deposition

We have improved the electronic properties of narrow-bandgap (Tauc gap below 1.5 eV) amorphous-silicon germanium alloys (a-SiGe:H) grown by hot-wire chemical vapor deposition (HWCVD) by lowering the substrate temperature and deposition rate. Prior to this work, we were unable to grow a-SiGe:H alloys with bandgaps below 1.5 eV that had photo-to-dark conductivity ratios comparable with our plasma-enhanced CVD (PECVD) grown materials [B.P. Nelson et al., Mater. Res. Soc. Symp. 507 (1998) 447]. Decreasing the filament diameter from our standard configuration of 0.5 mm to 0.38 or 0.25 mm provides first big improvements in the photoresponse of these alloys. Lowering the substrate temperature from our previous optimal temperatures (T_sub starting at 435 °C) to at 250 °C provides additional photo-to-dark conductivity ratio increasing by two orders of magnitude for growth conditions containing 20–30% GeH₄ in the gas phase (relative to the total GeH₄+SiH₄ flow).     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

激光熔覆Ni基B4C合金涂层的组织与性能研究

利用5kW连续波CO2激光器对16Mn钢基材表面预置的含20 vol%B4CP的Ni基合金复合粉末进行激光熔覆得到Ni基B4C合金涂层(NiB4c),研究了NiB4c涂层的组织形貌与相组成,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiB4C涂层由涂层下部的胞状晶和涂层中上部的树状枝晶及其间的共晶组织所组成,其组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,CrB,Ni3B,Fe2B,Fe23(C,B)6等化合物,涂层中存在未熔的B4C颗粒。激光熔覆NiB4c涂层比Ni60涂层具有较高的硬度和耐磨性,并分析了NiB4C涂层的强化机理。     

陶瓷表面化学镀的前处理工艺新进展

综述了非金属表面化学镀前处理工艺的现状和发展，对陶瓷化学镀的粗化和活化工艺的新进展进行了评述，侧重讨论了离子型、胶体钯型、浆料型、分子自组装吸附钯型、贱金属型活化工艺特点和进展，并展望了今后发展方向。     

Al-10Mg型固溶合金自然时效稳定性研究

测定了ZL30 5合金自然时效 33年的力学性能变化 ,观察了晶界的析出相 ,研究了组织和性能的关系 ,从而确定了ZL30 5合金具有长期自然时效稳定性。     

PECVD法低温沉积多晶硅薄膜的研究

在玻璃衬底上采用常规的PKCVD法在低温(≤400℃)条件下制得大颗较(直径＞100nm)、择优取向(220)明显的多晶硅薄膜。选用的反应气体为SiF4和H2混合气体。加入少量的SiH4后，沉积速率提高了近10倍。分析认为，在低温时促使多晶硅结构形成的反应基元应是SiFmHn(m n≤3)，而不可能是SiHn(n≤3)基团。     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。