High Temperature Property Development of Bauxite Based Bricks

Physical properties and microstructural evolution on firing of 3 types of bauxite based refractory bricks were carried out using techniques such as porosimetry,XRD and SEM.The groups differed from each other by progressive refining of the matrix or bond phase.It is revealed that such a refinement of the matrix can improve the high temperature properties of the bricks made from poor grade materials.     

激光熔覆Ni基B4C合金涂层的组织与性能研究

利用5kW连续波CO2激光器对16Mn钢基材表面预置的含20 vol%B4CP的Ni基合金复合粉末进行激光熔覆得到Ni基B4C合金涂层(NiB4c),研究了NiB4c涂层的组织形貌与相组成,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiB4C涂层由涂层下部的胞状晶和涂层中上部的树状枝晶及其间的共晶组织所组成,其组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,CrB,Ni3B,Fe2B,Fe23(C,B)6等化合物,涂层中存在未熔的B4C颗粒。激光熔覆NiB4c涂层比Ni60涂层具有较高的硬度和耐磨性,并分析了NiB4C涂层的强化机理。     

Al-10Mg型固溶合金自然时效稳定性研究

测定了ZL30 5合金自然时效 33年的力学性能变化 ,观察了晶界的析出相 ,研究了组织和性能的关系 ,从而确定了ZL30 5合金具有长期自然时效稳定性。     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

对基于交换网络分层结构的软件无线电方案的改进

通过比较各种软件无线电结构的优缺点,针对既具有交换网络结构又具有分层结构优点的基于交换网络的分层无线电结构方案,提出了部分改进思想。     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

H-bond and conformations of donors and acceptors in model polyether based polyurethanes

The molecular mechanics (MM) method with COMPASS force field was used to study the H-bonds in the polyether based polyurethane model molecules. Availability of the calculation was firstly verified in comparison of some H-bonded model molecules, which were studied by using ab initio calculation, and those calculated by MM. Based on a urethane model molecule 1,3-dimethylcarbamate, which can be donor or acceptor and behaves in various conformations, it is reasonable to have a large number of H-bond interactions between various conformational donors and acceptors. For examining all the possible interaction patterns, we studied 57H-bond complexes. This systematic modeling covers well-known four types of interaction patterns, such as NH?OC (Type I), NH?O-CO (Type II), NH?NH (Type III), NH?COC (Type IV) in the system. Obtained H-bond energies were used to analyze the probabilities of the complexes. For the interaction within the hard segments, or Type I, Type II and Type III, a predominant H-bond complex has been found in the present study, which belongs to Type I. For the interaction between the hard segment and the soft segment, two conformations of Type IV were calculated to be existed.     

大块非晶合金的性能、制备及应用

综述了大块非晶合金的性能、制备方法及应用，对比了吸铸法制备的棒状Zr41.2Ti13.8Cu12.5Ni10Be22.5,Zr57Cu20Al10Ni8Ti5,Zr52.5Ti5Cu17.9Ni14.6Al10(原子分数)大块非晶样品的过冷温度区间宽度(△Tx)，给出了3种大块非晶合金系列的热稳定性参数Tg、Tx及△Tx，提出了大块非晶合金领域存在的问题及发展方向．     

Finite element analysis of femoral components paper III – hip joints

Finite element analysis of the hip implant is conducted in this paper for representative femoral cross-section geometries and development of stress in the presence of bone cement is elucidated. Differences in cement stresses generated by varying implant cross-sections were compared with conventional features derived from representative implants. The analysis was performed under idealized implant assemblies by constraining the implant movement in the assembly. The cross-sections and implant geometries used are generic and intended to be representative of available geometries. This paper is a part of student research projects, prepared from a series of activities in biomedical implant research currently underway at Ohio Northern and Arkansas Tech Universities.     

Intergranular corrosion of a light aircraft aluminum alloy propeller

Examination of the wreckage of a light aircraft revealed that approximately 20 cm was missing from one tip of the aluminum alloy propeller. Fractographic and metallographic examination of the remaining portion of the propeller revealed extensive grain-boundary separation in the vicinity of the fracture, and grain edges and corners rounded by corrosion on the fracture surface. Energy dispersive X-ray analysis (EDXA) revealed fluorine on, and in the vicinity of, the fracture surface. In the ensuing litigation, it was asserted that the crash occurred because the propeller fractured in flight as the result of intergranular attack caused by the use of a fluorine-bearing cleaner.