钢筋网焊机自动生产线的实时控制

在网焊机自动化生产线的研制中,由于点焊控制器、自动上料机构中焊点总数多、驱动路数多、网格间距小、运行速度快,因而对控制系统的实时性提出了较高要求,用工控机与单片机、PLC组成的网焊机控制系统,在软、硬件实现上采取多种方案有机结合,实现了网焊机生产线的高速实时控制。     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

MHD simulation of high-current subsonic vacuum arc under different distributed axial magnetic fields

Based on two-temperature magnetic hydrodynamic (MHD) model, the influence of saddle-shaped distributed axial magnetic field (AMF, linearly increases along radial position) and bell-shaped distributed AMF (linearly decreases along radial position) on plasma loss and heat flux density to anode in subsonic high-current vacuum arc (HCVA) is simulated and analyzed. According to the simulation results, the saddle-shaped AMF can more effectively inhibit plasma loss from arc column than that of bell-shaped AMF. Comparisons between simulation results and experimental results further verify the correctness of model and simulation.     

Inactivation Kinetics of Tomato Juice Lipoxygenase by Pulsed Electric Fields

ABSTRACT: Pulsed electric field (PEF) inactivation models for tomato juice lipoxygenase (LOX) were studied. Tomato juice was treated by PEF with the combinations of electric field strength (0, 10, 15, 20, 30, 35 kV/cm), PEF treatment time (20, 30, 50, 60, 70 μs), and PEF treatment temperature (10, 20, 30, 40, 50 °C). The first-order inactivation models, Hulsheger's model, Fermi's model, and the 2nd-order polynomial equation adequately described the LOX inactivation. Calculated D values were 161.0, 112.9, 101.0, and 74.8 μs at 15, 20, 30, and 35 kV/cm, respectively, at 30 °C. The activation energy for the inactivation of LOX by PEF was 35.7 kJ/mol. Applied electric field strength was the primary variable for the inactivation of LOX.     

海洋平台双相不锈钢管线的焊接

就双相不锈钢的特异性能．介绍双相不锈钢管线的焊接特点与技术。     

铍铜电极在接触类焊机上的应用研究

接触焊用电极材料是接触类焊机的核心部件，要求具有优良的导电率，强度和高的耐高温性能（软化温度）等综合性能，本项目采用含铍多元铜合金，利用含铍铜合金具有较高的硬度，耐高温性能，强度和导电率的综合性能，研制出一种达到进口电极性能要求的长寿命新型电极材料，通过在进口及国产设备使用完全满足要求，解决了国产焊接电极长期存在的焊接质量差，寿命短的问题。     

电弧炉采用石灰石单渣冶炼工艺的研究

采用优质石灰石取代质量差的白灰 ,进行了单渣电弧炉熔炼。结果表明 ,钢水成本降低 ,钢水质量提高 ,取得了良好的效果。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.     

变压器事故原因分析

通过分析一次变压器事故的原因。指出变压器实际运行中存在的问题。并结合自己的工作经验提出科学的改进建议。     

唐钢ER70S-6焊丝钢的生产工艺研究及质量分析

介绍了唐钢ER70S-6焊丝钢的特点，对盘条质量进行了分析。对该钢化学成分、冶炼和轧制工艺进行了优化研究，使其综合性能明显改善。