Catalytic combustion synthesis of CNTs/MgO composite powders and the influences on the thermal shock resistance of low-carbon Al2O3–C refractories

Using MgC₂O₄, Mg powders as raw materials and Ni(NO₃)₂?6H₂O as a catalyst, CNTs/MgO composite powders were prepared by a catalytic combustion synthesis method. The CNTs/MgO composite powders were characterized by XRD, Raman spectroscopy, FESEM/EDS and HRTEM. The effects of catalyst content on the degree of graphitization and aspect ratio of the CNTs in composite powders were investigated. Moreover, the thermal shock resistance of low-carbon Al₂O₃–C refractories after adding the composite powder was investigated. The results indicated that the CNTs prepared with 1 wt% Ni(NO₃)₂?6H₂O addition had a higher degree of graphitization and aspect ratio. In particular, the aspect ratio could reach approximately 200. The growth mechanism of hollow bamboo-like CNTs in the composite powders was proven to be a V-L-S mechanism. The thermal shock resistance of Al₂O₃–C samples could be improved significantly after adding CNTs/MgO composite powders. In particular, compared with CM0, the residual strength ratio of Al₂O₃–C samples with added 2.5 wt% composite powders could be increased 63.9%.     

烟道流量计量标准装置

为了解决我国烟道流量计的量值溯源问题,中国计量科学研究院建立了烟道流量计量标准装置。装置使用可溯源至标准转盘的激光多普勒测速仪作为原级标准器,采用激光多普勒流速剖面扫描和超声流量计波动修正的方式测量标准流量,经校准的8声道超声流量计为工作级标准表,具备了908~104840m3/h的测量能力,扩展不确定度为0.62%(k=2),可对最大口径为1m的流量计进行校准。装置下游测试段包括圆形管段和矩形管段,能够开展烟道流量计测量性能的研究。     

内热型超声雾化溶液再生系统最优内热量的研究

基于质量守恒、能量守恒定律，建立了内热型超声雾化溶液再生系统（IH-UARS）的再生性能预测模型并进行了充分的实验验证，通过研究不同内热量下IH-UARS的再生性能及其变化规律，寻求系统所需的最佳内热量并明确其可能的影响因素。结果表明：IH-UARS系统存在最优的内热量范围，使其再生系统性能最佳；所需最优内热量随着再生溶液流量增大呈显著的对数增长，但受空气流量的影响较弱；在该研究中的标准工况下，IH-UARS所需最优内热量约为275~350 W。此外研究发现：内热量的增长有益于促进初始浓度较高的溶液进一步浓缩再生，如当IH-UARS中内热量增至800 W时，其初始浓度为36%的溶液比24%的溶液浓度增量指标改善幅度高37%。研究所得结果可对提高溶液再生性能及经济性提供积极参考。     

换能器结构参数对聚合物超声塑化黏弹生热的影响

为研究超声换能器结构参数对聚合物超声塑化过程黏弹性生热的影响，首先确定超声黏弹性生热系统的组成，进行纵振超声换能器结构设计；然后分析超声黏弹性生热过程及超声黏弹性生热原理；最后采用单一变量法分析超声换能器的主要结构参数对其纵振频率及工具头前端质点最大振幅的影响，将其实际输出的纵振激励加载于熔融聚合物，研究其结构参数对聚合物超声黏弹性生热过程及达到聚合物玻璃化转变温度所用时间的影响。结果表明，随纵振激励作用时间的增加，聚合物温度非线性升高；放大比对聚合物温度变化影响最大，前盖板厚度和工具头长度次之，影响最小的是变幅杆长度。     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

考虑流固耦合的管道机器人冲击环焊缝过程动力学建模与分析

以管道机器人（Pipeline inspection gauge，PIG）为载体的内检测技术是保障油气管道安全运输的重要手段。针对管内高压流体作用下，管道机器人在冲击管内环焊缝过程中产生的动力学行为突变问题。建立了管道周向受限空间中基于Kelvin弹簧阻尼的管道机器人密封盘等效动力学模型，结合管道机器人本体建立了多体系管道机器人动力学模型；详细推导了管道机器人轴向振动微分方程，以及管内流体的流动方程；并使用Matlab/Simulink与Adams进行流固耦合仿真，作为重要的工艺参数之一，研究了管道机器人速度改变时，其在冲击环焊缝过程中的动力学响应情况。结果表明：所建立的密封盘及管道机器人动力学模型能够很好地表征密封盘在管道轴向、径向以及周向的力学特性；运行速度越快，管道机器人通过环焊缝引起的轴向振动越剧烈，冲击振动越明显；而垂向和俯仰振动现象随运动速度增大而显著减弱。     

Investigation on the effect of EDM process variables and environments on acoustic emission signals

Abstract

The performance of electrical discharge machining (EDM) primarily depends on the spark quality generated in the inter-electrode gap (IEG) between the tool and workpiece. A method for obtaining accurate information about the spark gap is required to effectively monitor the EDM process. The rise and fall of thermal energy in the discharge zone at a rapid rate during the dielectric breakdown produces high-pressure shock waves. This work explores the suitability of using acoustic emission (AE) generated from these shock waves and the elastic AE waves released on the workpiece due to the induced stress to monitor the performance and spark gap in EDM. The information content of the AE signals acquired at various machining conditions was extracted using AE RMS, spectral energy and peak amplitude. These features were able to well discriminate the machining condition, tool material, workpiece material, flushing pressure, current density, the initial surface roughness of the tool. Additionally, the AE signal features had a good and consistent correlation with the performance parameters, including material removal rate, surface roughness (Ra and Rq) and tool wear. The findings lay the groundwork to develop an effective, non-intrusive in-situ AE-monitoring system for performance and IEG condition in EDM.     

Enhanced ionic conductivity and thermal shock resistance of MgO stabilized ZrO2 doped with Y2O3

The present work focused on the effect of Y₂O₃ co-doping on the phase composition, microstructure, ionic conductivity and thermal shock resistance of 8 mol% MgO stabilized ZrO₂ (Mg-PSZ) electrolyte ceramics for high temperature applications. The addition of Y₂O₃ could promote the process of monoclinic-to-cubic/tetragonal phase transformation and became the metastable phase at room temperature. Meanwhile, the grain size of Mg-PSZ decreased. It was demonstrated that an appreciable increase in the ionic conductivity and compressive strength occurred on substituting MgO with Y₂O₃ in the Mg-PSZ electrolyte ceramics across the measured temperature range. Moreover, the Y₂O₃ addition could restrain the adverse effect of the cyclic thermal shock on the ionic conductivity and compressive strength of Mg-PSZ. The main reason was that the increase of the amount of monoclinic phase caused by cubic/tetragonal-to-monoclinic phase transformation by the cyclic thermal shock was restrained after the Y₂O₃ addition.