High performance H2 sensor based on rGO-wrapped SnO2–Pd porous hollow spheres

Hydrogen (H₂) sensors based on metal oxide semiconductors (MOS) are promising for many applications such as a rocket propellant, industrial gas and the safety of storage. However, poor selectivity at low analyte concentrations, and independent response on high humidity limit the practical applications. Herein, we designed rGO-wrapped SnO₂–Pd porous hollow spheres composite (SnO₂–Pd@rGO) for high performance H₂ sensor. The porous hollow structure was from the carbon sphere template. The rGO wrapping was via self-assembly of GO on SnO₂-based spheres with subsequent thermal reduction in H₂ ambient. This sensor exhibited excellently selective H₂ sensing performances at 390 °C, linear response over a broad concentration range (0.1–1000 ppm) with recovery time of only 3 s, a high response of ～8 to 0.1 ppm H₂ in a minute, and acceptable stability under high humidity conditions (e. g. 80%). The calculated detection limit of 16.5 ppb opened up the possibility of trace H₂ monitoring. Furthermore, this sensor demonstrated certain response to H₂ at the minimum concentration of 50 ppm at 130 °C. These performances mainly benefited from the special hollow porous structure with abundant heterojunctions, the catalysis of the doped-PdO_x, the relative hydrophobic surface from rGO, and the deoxygenation after H₂ reduction.     

增材制造技术在超高膨胀封隔器中的应用

石油和天然气行业不断关注增材制造技术在航空航天和汽车行业的应用发展。研发了利用增材制造技术的超高膨胀封隔器,该封隔器的支承环系统由增材制造。增材制造设计大幅减少了支承系统的构件数量,同时显著提高了膨胀能力和额定压力。密封元件系统与增材制造支承环安装在一起,提供了极端膨胀比、零挤压间隙和对不规则孔的良好适应性。分析和测试结果表明:直径膨胀比高达111%,与常规封隔器相比,提高50%以上; 至少涵盖5种线重的套管(外径相同); 在148.89 ℃的温度下,密封元件能够保持压力68.95 MPa。介绍了增材制造技术、增材制造支承环概念、增材制造材料力学性能、密封元件系统优化和测试情况,以期给我国的完井作业提供借鉴。     

Finite element optimization of sample geometry for measuring the torsional shear strength of glass/metal joints

Assessment of mechanical properties of glass/metal joints is a challenging process, especially when the application relevant conditions of the joints have to be considered in the test design. In this study, a finite element method (FEM) is implemented to analyze a torsional shear strength test designed for glass-ceramic/steel joints aiming towards solid oxide fuel/electrolysis cells application. Deviations from axial symmetry of the square flanges (ends) of respective hourglass-shaped specimens and also supporting and loading sockets of the test set-up are included in the model to simulate conditions close to reality. Undesirable tensile stress and also shear stress concentration appear at the outer edge of glass-ceramic layers, which are less for the hollow-full specimen. The simulation results show that for a specimen with either 9 mm thick square- or 6 mm thick triangular-flanges, locally enhanced tensile stresses almost disappear, resulting in a symmetric shear stress distribution. The difference between the analytically derived nominal shear strength and the real critical shear stress derived via simulation reduces with decreasing the fracture torque.     

Adaptive GLR-, Rao- and Wald-based CFAR detectors for a subspace signal embedded in structured Gaussian interference

The problem of detecting a subspace signal embedded in subspace Gaussian interference and thermal noise is studied in this paper. In this problem, both the signal-independent and signal-dependent interferences are assumed to be present, therefore the overall interference subspace covers the signal subspace. The approach of this paper extends previous works involving either of those two kinds of interferences. A set of secondary data containing only interference plus noise is employed to estimate the interference covariance matrix and the noise power. Three new detectors are designed via the generalized likelihood ratio (GLR), Rao and Wald tests, respectively. Their probabilities of false alarms (PFAs) and detections are analytically derived. The PFAs show that the new detectors have the constant false alarm rate (CFAR) property against the interference and noise. Numerical results show that the new detectors outperform their counterparts for the studied problem. Furthermore, the new detectors are less sensitive to the secondary data size and to the mismatched subspace signal than some other detectors, such as the GLR detector (GLRD), the adaptive matched filter (AMF), the adaptive subspace detector (ASD), etc.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

基于压缩机-支架系统的异常噪声研究

针对某乘用车发动机转速在1 573 r/min，压缩机开启时车内噪声异常的问题，对样车进行试验分析与诊断，对压缩机-支架系统进行仿真分析，提出改进方案并验证改进效果。利用LMS声振信号采集系统采集振动噪声数据，采用频谱分析、阶次追踪等方法，并结合压缩机-支架系统模态仿真结果，确定车内异常噪声是压缩机轴频21阶与压缩机-支架系统3阶模态频率接近发生共振造成的。通过优化支架结构来提高压缩机-支架系统3阶模态频率以此来避免共振，并换装橡胶驱动盘缓和压缩机输入扭矩波动。将改进结构进行整车试验，结果表明：匀速工况空调开启时问题转速下，车内噪声降低了2.5 dB(A)；匀加速工况空调开启时发动机转速1 500~1 650 r/min区间，车内噪声无峰值，其余转速空调开启时改进前/后车内噪声基本不变，噪声波动趋势平缓。     

泳池式轻水反应堆内电磁线圈可控温辐照装置设计

本文设计了在泳池式轻水反应堆（简称泳池堆）内在线测量电磁线圈电性能的可控温辐照装置。采用MCNP程序进行中子物理计算，对泳池堆、线圈骨架的结构尺寸与物质组分进行了精细全尺寸模拟，得出辐照装置的发热功率和中子注量率。通过初步估算，使用ANSYS CFX进行了数值模拟，得出辐照装置内线圈在堆运行时的温度，并提出温度控制的方法。辐照装置采用铝材加工制造，并进行了垂直度测试、气压测试、检漏测试。增加了绝缘设计，将辐照装置与泳池堆之间进行绝缘。在线圈处预埋铠装热电偶，对线圈温度进行实时监测。在泳池堆内对电磁线圈进行辐照试验，结果表明，本文设计的辐照装置能满足电磁线圈在泳池堆孔道内进行辐照试验的要求，并可对电磁线圈进行实时温度控制。     

Multimodal sensing and active continuous closed‐loop feedback for achieving reliable manipulation in the outdoor physical world

The use of field robots can greatly decrease the amount of time, effort, and associated risk compared to if human workers were to carryout certain tasks such as disaster response. However, transportability and reliability remain two main issues for most current robot systems. To address the issue of transportability, we have developed a lightweight modularizable platform named AeroArm. To address the issue of reliability, we utilize a multimodal sensing approach, combining the use of multiple sensors and sensor types, and the use of different detection algorithms, as well as active continuous closed‐loop feedback to accurately estimate the state of the robot with respect to the environment. We used Challenge 2 of the 2017 Mohammed Bin Zayed International Robotics Competition as an example outdoor manipulation task, demonstrating the capabilities of our robot system and approach in achieving reliable performance in the fields, and ranked fifth place internationally in the competition.     

A review of the existing performance verification infrastructure for micro-CMMs

The performance verification of micro-CMMs is now of intense interest because of their capability to perform length measurements in three dimensions to high accuracy with low uncertainties. Currently, verification of micro-CMMs is completed in the spirit of existing specification standards, because strict adherence to these standards is often difficult. This review aims to present and discuss verification techniques available for micro-CMMs: specification standards, existing calibrated test lengths and traceability routes that can be associated with micro-CMMs. Three specification standards used in the testing of CMMs will be considered. In addition, a wide range of calibrated test lengths are reported, and any advantages and disadvantages associated with their use are discussed. It is concluded that micro-CMMs cannot yet be verified in accordance with existing specification standards. Suggestions are made for future standardisation work required to rectify these issues.