川西彭州地区雷口坡组潮坪相薄储层辨识机理研究

川西彭州地区三叠系雷口坡组雷四上亚段潮坪相薄储层识别难度极大。围绕如何从复合地震强反射中区分并识别上、下两套储层面临的地球物理难题,采用先“分”后“合”的研究思路,基于实际地层结构及不同储层叠加样式建立正演模型,利用全波场波动方程正演模拟技术,剖析了不同主频条件下薄储层的地震响应特征,通过波形差异化分析,从复合地震响应中“剥离”出了两套储层所引起的地震响应特征及变化规律,明确了两套储层在不同频带下的地震识别标志和识别方法,为该区强反射界面干扰下两套薄互层储层辨识机理分析及精准预测奠定了基础。基于不同频带下薄储层辨识机理的分析结果,定性预测了薄储层平面展布,提出了深层潮坪相薄储层识别和预测难题的解决方案,为该区地震资料品质评价、面向薄储层的地震采集技术设计、地震资料处理及薄储层预测提供了依据和指导。     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.     

公路隧道喷射混凝土套拱加固结构力学特性

为研究喷射混凝土套拱加固前后二次衬砌与混凝土套拱的受力状况,依托陕西汉中至留坝段八里关隧道,运用有限元软件建立隧道混凝土结构套拱加固分析模型,并通过现场监测获取二次衬砌与套拱间的接触压力、套拱格栅拱架钢筋应力、套拱混凝土应力,将数值模拟结果与现场测试结果相结合,得出套拱结构的一般受力变化规律。结果表明:套拱加固前衬砌结构的最不利荷载位置位于施工缝附近的拱顶、拱肩与拱脚处; 由于衬砌局部变形与温度应力的影响,套拱混凝土应力变化呈现反复“上升-下降-上升”最后趋于稳定的特点; 套拱的作用是控制二次衬砌的进一步变形,套拱施作后所承受荷载较小,套拱反作用力远小于围岩作用于衬砌的应力,在应力计算中不应将衬砌与套拱作为整体计算; 套拱结构数值模拟所得的结果与现场测试套拱结构内力(轴力、弯矩)的大小及分布相似度高,但在衬砌裂损严重部位,数值模拟所得结果误差较大,应以现场测试结果为准。     

Kariya (Hildegardia barteri) seed oil extraction: comparative evaluation of solvents,modeling, and optimization techniques

In this work, the effects of solid/solvent ratio (0.10–0.25?g/ml), extraction time (3–8?h), and solvent type (n-hexane, ethyl acetate, and acetone) together with their shared interactions on Kariya seed oil (KSO) yield were investigated. The oil extraction process was modeled via response surface methodology (RSM), artificial neural network (ANN) and adaptive neuro-fuzzy inference system (ANFIS) while the optimization of the three input variables essential to the oil extraction process was carried out by genetic algorithm (GA) and RSM methods. The low mean relative percent deviation (MRPD) of 0.94–4.69% and high coefficient of determination (R²) > 0.98 for the models developed demonstrate that they describe the solvent extraction process with high accuracy in this order: ANFIS, ANN, and RSM. The best operating condition (solid/solvent ratio of 0.1?g/ml, extraction time of 8?h, and acetone as solvent of extraction) that gave the highest KSO yield (32.52?wt.%) was obtained using GA-ANFIS and GA-ANN. Solvent extraction efficiency evaluation showed that ethyl acetate, n-hexane, and acetone gave maximum experimental oil yields of 19.20?±?0.28, 25.11?±?0.01, and 32.33?±?0.04?wt.%, respectively. Properties of the KSO varied based on the type of solvent used. The results of this work showed that KSO could function as raw material in both food and chemical industries.     

煤矿下山巷道水与空气不耦合装药爆破技术对比研究

为了提高三级煤矿许用炸药能量利用率,改善爆破破岩效果，保证开采区的工作效率，对不耦合装药结构进行优化，以理论推导的方式分别得出空气不耦合与水不耦合装药系数对爆生气体准静压力的影响，并进行了对比分析；通过实验室爆破模型试验研究水和空气径向不耦合分别作用下爆炸应力波的传播分布特性，分析峰值应力与测点到炮孔比例距离、不耦合系数之间的关系，并与理论分析对比验证。结果表明：当不耦合系数相同时，炮孔处水不耦合装药爆炸应力波峰值高于空气不耦合装药，随着不耦合系数的增加，炮孔处爆炸应力波的峰值应力减小；模型试验测得同一测点的水不耦合装药峰值应力是空气不耦合装药峰值应力的1.15~1.52倍，峰值应力作用时间长于空气不耦合装药，同一测点水和空气不耦合装药结构测得的应力波及其峰值应力均随不耦合系数的增加呈负幂函数衰减，且空气不耦合装药时衰减得更快，与理论分析一致；贵州某煤矿下山巷道，于梯形掘进断面实施传统空气不耦合装药结构掏槽爆破，效果不甚理想，运用水不耦合装药爆破技术，提高了炮孔利用率，减小了岩石破碎块度，使爆堆集中，显著提高了岩石破碎效果与出渣效率。     

Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

Models for circular data from time series spectra

Circular data are those for which the natural support is the unit circle and its toroidal extensions. Numerous constructions have been proposed which can be used to generate models for such data. We propose a new, very general, one based on the normalization of the spectra of complex-valued stationary processes. As illustrations of the new construction's application, we study models for univariate circular data obtained from the spectra of autoregressive moving average models and relate them to existing models in the literature. We also propose and investigate multivariate circular models obtained from the high-order spectra of stationary stochastic processes generated using linear filtering with an autoregressive moving average response function. A new family of distributions for a Markov process on the circle is also introduced. Results for asymptotically optimal inference for dependent observations on the circle are presented which provide a new paradigm for inference with circular models. The application of one of the new families of spectra-generated models is illustrated in an analysis of wind direction data.     

枪管结构对固有频率的影响

为了研究枪管结构对枪管固有频率的影响,针对枪管尤其是狙击枪管设计中约束长度、枪管外形、膛口装置以及膛线等不同结构,建立了相应的三维模型。采用以六面体为主的网格对枪管进行了网格划分,采用有限元方法对枪管进行了模态分析。计算获得了不同结构枪管的固有频率; 通过比较,得到了不同枪管结构对固有频率的影响。分析结果表明:枪管尾部螺纹长度越长,枪口振动幅度越低; 相同质量枪管,锥形外形枪管刚度最好; 加装膛口装置对枪管刚度和振动特性有不利影响。     

射频电缆的幅相稳定性测试研究

对射频电缆幅相稳定性进行了介绍,阐述了射频测试电缆相位和幅度变化的因素,并详细分析了射频电缆相位性能以及幅度性能的不同测试方法,最后通过实测数据的展示,总结说明了在日常测试中该如何正确使用测试电缆。