Modeling and simulation of a fully air swept ball mill in a raw material grinding circuit

A raw material grinding circuit was modeled using plant data. Samples were collected from around the circuit and, following a crash stop, from inside the mill. The size distributions of the samples were determined down to a few microns. Using the data from inside the mill a modeling approach, based on perfect mixing, was developed. The modelling approach implicitly assumes that the mixture of feed materials broken is homogenous from the breakage point of view. The air classification around the circuit was modeled using the efficiency curve approach. In order to measure the success of the method the circuit performance was predicted by simulation studies while it was operating at different conditions. The results were then compared with the measured data. It is concluded that modeling gives a useful quantitative indication of what may occur in fully air swept mills.     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

复杂断块油藏剩余油分布及配套挖潜对策

复杂断块油藏开发后期剩余油分散而难以识别，且其分布受多种因素的控制。在大港油区的港东开发区，根据以纵向1118个时间地层单元为对象的精细油藏描述，提出3类剩余油潜力：①已动用油层，即断层与微构造控制、注采井网不完善、层间非均质性、平面低渗透相带、层内渗流屏障、注采滞留区、边底水锥进等因素形成的剩余油；②新层，即以往未发现的低电阻油层和新发现油砂体；③滚动扩边。在潜力认识的基础上，以单砂体或流动单元为挖潜调整对象，在潜力富集区钻新井、更新井，改变非主力层的驱动方式，重组层系、井网，改变液流方向和间歇注水，并对潜力区配套实施补层、提液、压裂防砂、重复射孔、深度调剖等措施。港东开发区复杂断块油藏实施配套挖潜措施后，提高了高含水期的开发效益与水平。图1参17     

Preparation of clean coal by flotation following ultra fine liberation

This paper reports the results of current fundamental research at the Department of Process Engineering, University of Miskolc on the processing of clean coal from Mecsek bituminous coal, Southern Hungary. The theoretical possibility of the separation of different petrographic components was proven experimentally and their liberation degree was determined based on the petrographic composition, flotation kinetic study of isolated components (groups of components), scanning electron microscopy and microprobe analyses. The mill with stirred ball media was chosen for the ultra-fine liberation of the coal components. It was revealed that along with the liberation of coal components, their surface oxidation and spontaneous agglomeration, entrapping the mineral impurities take place in ultra-fine grinding. This paper discusses the interfacial phenomena occurring in the ultra-fine grinding process and their influence on the flotation. The concept for the advanced preparation of clean coal was developed, tested and proved. The main steps of this concept are the ultra-fine liberation in the stirred-media mill, the de-agglomeration of flocs spontaneously formed during the ultra-fine grinding and the induced (hydrophobic) flocculation with the following two-step flotation in a flotation column.     

Dynamics of Vibroprotective Systems with Roller Dampers of Low-Frequency Vibrations

We study low-frequency vibrations of a vibroprotective system of solid bodies formed by a roller damper and a moving load-carrying body under the action of external harmonic excitations. The dynamic equations of combined motion of the working body of the damper over the hinged roller without sliding and the load-carrying body are deduced and numerically analyzed. A new procedure is proposed for the evaluation of the optimal parameters of adjustment of roller dampers in nonlinear systems.     

金刚烷最新研究

金刚烷是近 30年来发展起来的一种新型精细化工原料。简要介绍了金刚烷的分子结构、性质及其主要用途 ,重点对近年来国内外报道过的金刚烷合成方法进行了评述 ,在此基础上指出了金刚烷化工的未来发展趋势。     

等径弯角挤压工艺(ECAEP)研究现状

等径弯角挤压是制备块状细晶材料的一种大塑性变形工艺，目前得到国内外高度重视．本文简要介绍了等径弯角挤压工艺的基本原理和变形特点，从理论上对其变形方式和机理进行了分析，并详细介绍了该工艺的应用领域。     

制备单根大重量喷涂钼丝的生产研究

全面系统地介绍了“大坯料轧制开坯-大加工率变形-长线拉伸”制造喷涂钼丝的工艺。重点阐述了Y370、Y250型三辊连轧机实现一火轧制开坯和长线拉伸增加在线碱洗工序对提高喷涂钼丝内部组织结构和外部表面质量的影响。分析了工艺中出现的问题，提出了相应的解决办法。     

用φ76 mm穿孔机组生产φ63mm毛管的设备改进

介绍了用Φ76mm穿孔机组生产Φ63mm毛管的设备概况及其改进。改进后，Φ76mm穿孔机组增加了产品范围为后面的冷技工序减少了拉拔道次，从而降低了Φ51mm以下冷拔管的生产成本。     

直缝焊管机组生产冷弯型钢产品初探

主要介绍了φ２１９直缝焊管机组生产高速公路护栏 成型原理、工艺布置、变形方式、变形图和轧辊设计。