多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。     

The formation of fibrous structure of polyamide 6 induced by the three-step forming process and its prominent reinforcement in nitrile rubber

Nitrile rubber (NBR) blends with excellent performance have always been a hot research topic in petroleum field. Due to the excellent performance and compatibility of polyamide 6 (PA6), it provides an opportunity for the preparation of high-performance NBR/PA6 blends. In this article, NBR/PA6 blends were prepared by the three-step molding process. Experimentally, it was found that PA6 has a prominent reinforcement effect in NBR matrix. The variation of this mechanical property was investigated from different aspects of the crystal structure, crystallinities, phase morphology, and so on. It can be cleared that the formation of fibrous structure of PA6 phase is the main factor for reinforcement of the polymer blends. Meanwhile, the formation mechanism of the special phase structure induced by the three-step process is deeply expounded and its structural evolution schematic is established. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47472.     

宏阳煤矿薄煤层沿空留巷实践应用

为了缓解矿井采掘接替紧张局面,宏阳煤矿采用沿空留巷技术,对12102运输顺槽采取顶板超前采面打设锚索梁、顶板超前预裂爆破,留巷段采用“钢梁+单体液压支柱”的方式进行巷道支护。该技术现场应用后,减少了巷道掘进工程量,减少了煤炭损失,增加了经济效益,降低了职工劳动强度,有利于采掘接替。     

不同含量低污染水对人工湿地中细菌的影响研究

探究水平流人工湿地(HFCW)系统处理低污染水过程中,相同COD/ρ(TN)下不同碳氮含量对细菌群落结构的影响。结果表明,进水为较高碳氮含量的HFCW(HF1)和进水为较低碳氮含量的HFCW(HF2)对COD和TN的去除效率具有一定的差异,HF1和HF2对COD的去除效率分别为48.26%和28.89%,对TN的去除率分别为79.06%和81.87%。HF1中细菌的丰富度和多样性均高于HF2,HF1中富集的优势细菌为Chloroflexaceae、Comamonadaceae和Rhodocyclaceae,均具有异养反硝化功能,HF2中富集的优势细菌为Xanthomonadaceae和Rhodocyclaceae,其中Xanthomonadaceae具有自养反硝化功能。COD、NH4^+-N和NO3^--N对HF1中细菌群落的影响大于对HF2中细菌群落的影响,HF1中COD对细菌群落的影响大于NH4^+-N和NO3^--N。     

某铁矿隔水护顶矿柱厚度计算及安全影响预测

科学合理地确定矿山隔水护顶矿柱安全厚度是矿山安全生产的前提条件，为保障某铁矿地表民房、道路等建（构）筑物安全，防止矿山开采过程中产生的导水裂隙带贯通第四系含水层，采用荷载传递交汇线法、K.B.鲁别涅依他估算法和冒落带、导水裂隙带高度估算法3种理论分析方法对隔水护顶矿柱厚度进行计算，并利用数值模拟手段对留设隔水护顶矿柱后的开采过程安全影响进行了分析，对理论计算结果进行了验证。3种理论计算方法得出的隔水护顶矿柱厚度分别为14.3～17.3 m、17.5～31.4 m和41.8～57.4 m，推荐隔水护顶矿柱留设厚度为60 m。通过数值模拟分析得出，在留设60 m厚的隔水护顶矿柱的基础上，开采区域和隔水护顶矿柱位置产生的最大拉应力约0.47 MPa，矿山开采不会对隔水护顶矿柱造成破坏；地表产生的最大水平位移约5.8 cm，最大垂直位移约26.5 cm，最大倾斜为1.70 mm/m，最大曲率为0.20 mm/m2，最大水平变形值为0.70 mm/m，满足相关规范要求，预测矿山开采不会造成地表建（构）筑物破坏。     

Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

测量二次电子空间分布特征矩阵法的有效性分析

为了准确测量不同材料在实际环境中的二次电子空间分布，设计了一种新型的二次电子发射空间分布测量结构，给出了实验测量原理，用求解特征矩阵的方法对实验结果进行处理，得到了所需的二次电子空间分布。通过模拟计算对该测量方法进行了校验，模拟结果与假设二次电子空间分布函数相吻合，表明该测量方法可靠、测量精度高，为后续样机研制奠定了理论基础。     

煤矿下山巷道水与空气不耦合装药爆破技术对比研究

为了提高三级煤矿许用炸药能量利用率,改善爆破破岩效果，保证开采区的工作效率，对不耦合装药结构进行优化，以理论推导的方式分别得出空气不耦合与水不耦合装药系数对爆生气体准静压力的影响，并进行了对比分析；通过实验室爆破模型试验研究水和空气径向不耦合分别作用下爆炸应力波的传播分布特性，分析峰值应力与测点到炮孔比例距离、不耦合系数之间的关系，并与理论分析对比验证。结果表明：当不耦合系数相同时，炮孔处水不耦合装药爆炸应力波峰值高于空气不耦合装药，随着不耦合系数的增加，炮孔处爆炸应力波的峰值应力减小；模型试验测得同一测点的水不耦合装药峰值应力是空气不耦合装药峰值应力的1.15~1.52倍，峰值应力作用时间长于空气不耦合装药，同一测点水和空气不耦合装药结构测得的应力波及其峰值应力均随不耦合系数的增加呈负幂函数衰减，且空气不耦合装药时衰减得更快，与理论分析一致；贵州某煤矿下山巷道，于梯形掘进断面实施传统空气不耦合装药结构掏槽爆破，效果不甚理想，运用水不耦合装药爆破技术，提高了炮孔利用率，减小了岩石破碎块度，使爆堆集中，显著提高了岩石破碎效果与出渣效率。     

SBBR反应器中耐冷微生物的驯化与识别

以模拟生活污水为处理对象，三种不同填料为生物膜载体，运行 A、B、C三个SBBR，通过逐步降温（25、20、15、10、6和5℃）培养驯化处理低温污水的生物膜。运行251周期，三个反应器COD出水浓度均低于50 mg/L；B反应器对氨氮去除效果优于A和C。特别在低温5℃时，A、B和C三个反应器氨氮平均出水浓度分别为14.1、3.79和14.1 mg/L。高通量测序结果显示，5℃时，三个反应器中均以降解有机物的微生物为主；只有B反应器中驯化富集出了嗜冷硝化菌（Candidatus Nitrotoga）；而其他有硝化作用的菌属在B反应器中的丰度也高于A和C反应器；不利于脱氮的类固氮菌（Elstera）在A和C反应器中丰度较高。此结果可从微生物角度解释三个反应器处理效果的差异性，表明B反应器处理低温污水有显著优势，其所用填料可结合低温菌进一步开发利用。