安钢1#煤气混合加压站的单加压改造实践

阐述了煤气混合加压站运行中的不足，提出了单加压焦炉煤气和叶轮两方面改造的措施，并取得了良好的效果。     

加固改造中的结构承重体系转换

从加固改造工程的实践出发 ,探讨了混合结构向框架结构体系转换的方法和构造措施 ,为实际工程提供了新的技术思路     

Further evidence of responsibility of impurities in MgO for variability in its basicity and catalytic performance in oxidative coupling of methane

Further evidence was delivered that certain impurities, which could be contained in MgO samples, might be responsible for observed variability in MgO basicity and catalytic performance in oxidative coupling of methane. The surface basicity/base strength distribution of a series of MgO samples containing or not containing Ca and Na impurities was determined by a temperature-programmed desorption of CO₂. It was revealed that samples containing Ca and Na impurities have much more medium, strong and very strong basic sites. The surface basicity of MgO samples containing added alkali or alkaline earth compounds or water was characterized by a test reaction of transformation of 2-butanol. It was confirmed that the introduction of these compounds to a pure MgO enhanced both its basicity and activity in oxidative coupling of methane.     

气象图数据的提取与转换

对气象图中等值线数据的提取与转化问题进行了研究 ,其中包括图像的二值化、细化、矢量化以及提取数据的转换和还原。它为从已有的气象图像资料中获得数据资料提供了一条有效的途径     

激光冲击诱发相变的实验研究

本对激光冲击是否可以诱发相变进行了试验研究。用功率密度为１．０６×１０＾８Ｗ／ｃｍ＾２的激光器冲击Ｔ８钢表面。实验结果表明激光冲击处理使Ｔ８钢的表面显微硬度有所提高并可以发生马氏体相变。冲击处理后材料表面硬度提高了两倍，认为相变是Ｔ８钢表面硬度提高的原因之一。     

激光相变硬化对离子渗氮层的影响

采用ＸＰＳ研究了３５ＣｒＭｏ钢离子氮化加激光相变硬化复合处理后不同层深处氮的变化。结果指出，复合工艺可在表层获得更深的氧氮化物层，含氮层的深度也将加大，并且与原渗氮层相比可在更深的位置得到氮化物层。     

轴端沟槽底部激光强化工艺参数优化研究

分析了选用不同激光能量密度对HT300进行表面强化处理时，材料表面呈现的四种状况；未相变硬化、相变硬化、表面微熔与表面熔凝的金相组织。根据工艺要求，选取相变硬化方法对轴端沟槽底表面进行处理。分析了工件激光处理方法并通过试验研究，寻找轴端沟槽底部激光强化工艺参数；激光功率（P）、光斑直径（D）及扫描速度（V）的优化组合。硬度测试及耐磨性能试验表明：激光相变处理和激光熔凝处理后轴端沟槽底部表面较表面感应淬火硬度分别提高7%和34%，绝对磨损体积分别下降了13%和25%。实践证实，对轴端沟槽底部激光相变硬化处理方法较其他表面处理方法工艺简单，加工工件符合技术要求，试验结果对零件表面处理提供了可靠依据。     

浅析体系转换法和粘贴碳纤维加固法在桥梁加固中的应用

通过对桥梁加固技术的研究，讨论了体系转换法和粘贴碳纤维布加固法的具体应用。     

Hydrothermal Synthesis of Acicular Lead Titanate Fine Powders

A pure, acicular lead titanate (PbTiO₃) fine powder with a white color has been prepared by hydrothermal synthesis. It is a new phase of PbTiO₃ with I 4 symmetry, cell parameters of a = 12.358 Å and b = 14.541 Å, and a density of 6.80 g.cm⁻³. The influences of pH (12.5 to 14.4), Pb/Ti ratio (1.0 to 1.6) in the feedstock, reaction temperature (130° to 230°C), time (0.25 to 4 h), starting materials, and additives on the formation of acicular PbTiO₃ under hydrothermal conditions have been investigated. The acicular PbTiO₃ with I 4 symmetry, referred to as the PX phase, can be converted to the perovskite-type (PE phase) of PbTiO₃ at about 605°C while its acicular morphology is essentially unchanged. The preferable conditions for preparing pure acicular PX-phase PbTiO₃ are that the pH is 13.0 to 14.0, Pb/Ti ratio is >1.3, reaction temperature is 170° to 200°C, time is 0.5 to 1.0 h, titanium butoxide (Ti[O(CH₂)₃CH₃]₄) is the starting material, and poly(vinyl alcohol) is an additive. The acicular grain of the PX phase is usually less than 100 nm in diameter and more than 1000 nm in length.     

图像处理中自适应数学形态学的研究

实际图像处理中当视场的变化引起目标变形时,固定大小的形态学算子很难达到较好的处理效果。研究了利用距离变换自适应地调整结构元大小的方法,即根据图像的不同位置来调整结构元素的大小,从而实现图像的形态学运算,并由此推导出了快速计算方法,最后测试了这种新算法的有效性。实验结果表明,该算法取得了较为理想的效果。