水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。     

基于StruCAD-3D的旅大4-2海洋修井机井架设计计算

应用专业结构计算软件StruCAD-3D对旅大4-2海洋修井机井架进行了设计计算,为井架结构的合理布局和选材提供了理论依据。通过计算分析,得知StruCAD-3D可以满足井架设计计算要求,同时还具有风载自动计算功能、单元检查功能和一次完成多种工况计算功能。     

一种估算单桩经济直径的方法

在滩海油田开发过程中,经常需要设立立管桩,在环境荷载的作用下,立管桩顶部会发生位移,较大的位移对立管及栈桥的安全很不利,因此需要合理确定单桩的直径。埕岛油田在确定单桩直径时引入了经济直径的概念,文章对经济直径的原理进行了分析,给出了桩顶位移和桩径经济指数计算公式,并举例进行了计算,得出了桩径与桩顶位移及桩径经济指数的关系曲线, 进而求得经济桩径的取值范围。文章还对该方法的优缺点进行了分析。     

一般阵列误差情况下信号二维方向角估计

针对均匀圆阵存在一般阵列误差的情况,提出一种信号二维方向角估计方法.基于均匀圆阵的阵列流形和阵列输出的协方差矩阵,采用加权总体最小二乘法估计信号二维方向角.并给出了解整周期性模糊的方法.计算机仿真表明了此方法估计精度高,对阵列误差鲁棒性强,并且各项性能都接近于CRB.     

A multigrid accelerated hybrid unstructured mesh method for 3D compressible turbulent flow

 A cell vertex finite volume method for the solution of steady compressible turbulent flow problems on unstructured hybrid meshes of tetrahedra, prisms, pyramids and hexahedra is described. These hybrid meshes are constructed by firstly discretising the computational domain using tetrahedral elements and then by merging certain tetrahedra. A one equation turbulence model is employed and the solution of the steady flow equations is obtained by explicit relaxation. The solution process is accelerated by the addition of a multigrid method, in which the coarse meshes are generated by agglomeration, and by parallelisation. The approach is shown to be effective for the simulation of a number of 3D flows of current practical interest. Sponsored by The Research Council of Norway, project number 125676/410 Dedicated to the memory of Prof. Mike Crisfield, a respected colleague     

Formulation of a ceramic ink for a wide-array drop-on-demand ink-jet printer

This paper describes the methodology for simulating a reprographic ink with a ceramic ink based on a commercially available zirconia powder for direct ceramic ink-jet printing. Of over-riding importance was matching viscosity and this was tested systematically by using a mineral oil–hexane binary system. Of secondary importance was adjustment of the pressure defect behind the nozzle to compensate for small differences in surface tension. The inks tested in the wide array print-head were based on low electrical conductivity liquids to avoid damage to the electroding system. The organic binder for the zirconia ink was paraffin wax and the dispersant was a hydroxystearic acid based polyester.     

硅胶固载光敏剂的合成及其在反式维生素D3光敏异构化为顺式维生素D3中的应用

采用丙二酸作为连接,针9－蒽甲醇连接到硅胶上生成硅胶固载的光敏剂。利用此因相光敏剂分别在乙醇和甲苯溶液中敏化反式维生素D3。实验结果表明，此固相光敏剂能够有效地敏化反式维生素D3为顺式维生素D3的反应，并且非常容易从反应体系中分离出来。     

忠武输气管道悬索跨越设计创新及探讨

忠武输气管道有4次悬索跨越,分别是蚂蝗溪悬索跨越、木龙河悬索跨越、马水河悬索跨越、野三河悬索跨越。文章介绍了这几座悬索跨越管桥设计中采用的多项新技术,如采用热聚乙烯半平行钢丝索代替以往的钢丝绳;采用钢管塔架代替以往的角钢塔架;根据地形地貌特点变换风索型式或取消塔架等。这些新技术、新设计在工程中均取得了良好的效果。另外,文章还针对悬索跨越桥面结构型式、预拱度设置、不对称荷载的影响、风索基础的设置等问题进行了探讨。