纤维素LiCl/DMAc体系的溶液特征

本文研究了纤维素LiCl／DMAc体系的溶液特征。实验结果证明该体系具有良好的时间稳定性和热稳定性，能在常温下近30天内没有明显的粘度降低；在100℃高温下，4h不降解。同时测定了溶液的特性粘数和Huggins常数，Huggins常数在0．4～0．6之间，对比纤维素的铜乙二胺（Cuen）溶液，发现特性粘数[η]LICI/DMAc＞[η]Cuen，无扰尺寸ALiCi／DMAc＞ACuen，可见在LiCl／DMAc体系中，溶剂与纤维素分子表现出更强的相互作用力，分子链充分伸展。该体系的特性粘数、粘度常数不仅与温度、溶剂有关，而且是LiCl浓度的函数，具有与聚电解质溶液相类似的性质。这可能是因为纤维素分子链上的H质子和溶液中的Cl-离子相互作用，而使纤维素分子带上部分电荷，相互排斥而引起的。因此利用M－H方程测分子量，粘度常数的确立必须考虑诸多因素的影响，否则会导致分子量的高估。     

扩链剂对阳离子聚氨酯乳液性能的影响

本文讨论了用三乙醇胺制备阳离子聚氨酯乳液，三乙醇胺用量，扩链剂，如乙二醇、丁二醇、二甘醇、三甘醇对乳液性能的影响。还讨论了扩链剂对其粘结强度的影响。     

Modification of cellulose fiber with silk sericin

Cellulose fiber surface was modified with silk sericin (or simply, sericin). Sericin fixation on cellulose was confirmed by environmental scanning electron microscopy (ESEM) and Fourier transform infrared spectrophotometry–attenuated total reflectance (FTIR‐ATR). Sericin content in finished samples was estimated by dyeing treated fabrics with an acid dye, Supranol Bordeaux B, and determining K/S and L values of the dyed fabrics. The treated fabrics were tested for free formaldehyde content, crease recovery, tensile strength, electrical resistance, water retention, and biocidal activity. From ESEM and FTIR‐ATR results, it was found that sericin coated onto cotton surfaces as a film. Increasing sericin content in the finishing solution increased the amount of coated sericin, and a greater depth of color in dyed samples and reduced free formaldehyde content in treated samples were observed. The sericin content in samples was found to have a negligible influence on tensile strength and crease recovery angle. With increasing sericin content, electrical resistivity of the samples dramatically decreased and water retention increased, indicating that sericin‐treated fabrics may be comfortable to wear because of its maintenance of moisture balance with respect to human skin. Because cotton textile coated with sericin exhibited low formaldehyde content and no biocidal activity against Klebsiella pneumoniae and Staphylococcus aureus, the fabric may reduce skin irritation and disturbance of physiological skin flora arising from textile contact. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1421–1428, 2005     

取代基及分子量对非离子型纤维素醚表面特性的影响

根据Washburn的浸渍理论(Penetration Theory)和van Oss-Good- Chaudhury的组合理论(Combining Theory)及应用柱状灯芯技术(Column Wicking Technique),对几种非离子型纤维素醚,如甲基纤维素、羟丙基纤维素和羟丙基甲基纤维素的表面特性进行了测试。由于这些纤维素醚的取代基、取代度和分子量不同,所以它们的表面能及其组成部分有着明显的差异。数据说明,非离子型纤维素醚Lewis碱大于Lewis酸,表面自由能的主要成分是Lifshitz-van der Waals力。羟丙基的表面能及其成分都大于羟甲基。而在相同取代基和取代度的前提下,羟丙基纤维素的表面自由能正比于分子量;而羟丙基甲基纤维素的表面自由能则正比于取代度,反比于分子量。实验还发现非离子型纤维素醚中的取代基羟丙基和羟丙基甲基的表面能似乎都大于纤维素的表面能,而实验证明所测试得出的纤维素的表面能及其成分的数据是与文献所吻合的。     

Rheological study on O−carboxymethylated chitosan/cellulose polyblends from LiCl/N,N‐dimethylacetamide solution

An O?carboxymethylated chitosan (O? CMCh) water solution (I) and N,N‐dimethylacetamide (DMAc) emulsion (II) were blended with a cellulose LiCl/DMAc solution, and corresponding polyblends (Polyblends I and II) were obtained. The rheology of the three fluids, that is, the cellulose solution and Polyblends I and II, was investigated. The cellulose solution was characterized by a power‐law fluid. When an O‐CMCh water solution or DMAc emulsion was added to the cellulose solution, the power‐law curve was preserved. The power‐law indexes (n) of all three fluids increased along with the temperature. Polyblend I displays an n close to but a little higher than that of the cellulose solution, while Polyblend II shows a much higher power index than those of the other two fluids. The values of the apparent viscosity (η_a) for all the three fluids are close and decrease along with an increase in the temperature. Adding O‐CMCh microparticles into Polyblends I and II results in a decrease in the structural viscosity index (Δη) in comparison to that of the cellulose solution, and this effect is very obvious for Polyblend I. A cellulose solution's Δη declines with the augmentation of temperature, while the Δη's of both Polyblends I and II show minimum values at about 323 K. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1719–1725, 2003     

不同预处理条件下纤维素的结构变化及其在DMAc／LiCI中的溶解

介绍了乙二胺、氢氧化钠和高温等三种不同的纤维素预处理方法。研究预处理后纤维素的结构变化，讨论预处理过程中的转化机理，并通过X射线衍射对纤维素结晶度的变化进行表征，证明乙二胺预处理后纤维素的结晶度下降最大。纤维素经过预处理后可以溶解在DMAc／LiCI中，讨论其溶解机理，通过对比三种预处理纤维素的溶解性能，表明经过乙二胺预处理之后的纤维素在DMAc／LiCI中溶解性能最好，氢氧化钠预处理的纤维素次之，高温预处理的纤维素溶解性能相对较差。     

阳离子表面活性剂CTAC对硫酸铝混凝除浊的影响

研究了阳离子表面活性剂十六烷基三甲基氯化铵(CTAC)在不同pH条件下对硫酸铝混凝除浊的影响。结果表明,含有CTAC的原水在适当的搅拌强度下能发生一定的絮凝作用。使用硫酸铝作为混凝剂时,低浓度的CTAC (≤50mg/L)可适当增强其混凝除浊效果,而高浓度的CTAC(100mg/L)则干扰其混凝。CTAC通过静电引力吸附于高岭土颗粒表面,因而其对硫酸铝混凝除浊的影响是通过电性中和及吸附架桥两种机理的结合而完成的,两者以何为主,视pH值、CTAC和硫酸铝的浓度而定。     

α-蒎烯阳离子聚合工艺的改进

以A lC l3/SbC l3为催化剂,用SbC l3逐步滴加方式,通过两步聚合工艺制备了α-蒎烯树脂。通过正交实验,对α-蒎烯调控聚合的各影响因素进行了研究。结果表明,与传统的一步聚合工艺相比,该工艺在保持单体高转化率的同时,使聚合反应变缓,避免了由于反应过快而引起的聚合产物中低聚体含量高,Mn下降的现象;有效提高了聚合物的软化点;降低了聚合物的色值。在优化工艺条件下,催化剂用量比传统工艺减少30%以上,制得的α-蒎烯树脂软化点为138℃(环球法),色泽3(铁钴色),得率达81.0%,软化点提高8℃以上,色泽降低2级以上。产品各项指标均超过了我国行业标准LY/T1453—1999特级水平。     

分光光度法测定水中十六烷基三甲基溴化铵的含量

通过可见光谱法研究了十六烷基三甲基溴化铵(CTAB)与甲基橙(MO)的显色反应,提出采用分光光度法测定水中十六烷基三甲基溴化铵的方法。结果表明,在体积分数为20%乙醇水溶液中,CTAB与MO形成1∶1的黄色离子缔合物,最大吸收波长位于470 nm处,摩尔吸光系数ε=1.404×103L.mol-1.cm-1,CTAB的浓度在0~6.0×10-4mol/L符合比耳定律。方法简便,快速,适于水样中CTAB的测定。     

阳离子双子表面活性剂的应用研究进展

介绍了阳离子双子表面活性剂近年来在新材料制备、抗腐蚀、杀菌、三次采油、织物染整、生物技术及造纸工业等方面的应用。