Optimal filtering and control for wireless networked closed-loop control systems

This article studies the optimal filtering and control for wireless networked control systems (WNCSs). In WNCSs, packets may be lost in both control and feedback channels and user datagram protocol is usually used to improve the performance of the real-time control. Relevant literature indicates that the conventional optimal filtering for such a system cannot be applied in practice due to the complex calculation with Gaussian mixtures. This paper proposes a novel scheme to realize the optimal filtering and the linear quadratic Gaussian control for WNCSs, in which the controlled node performs a local estimation and the remote-control node performs the final estimation and control, and a synchronization of two estimators is guaranteed by a communication mechanism. An optimal filtering algorithm is developed, the stability condition of the filtering error covariance is obtained, optimal finite-horizon and infinite-horizon control are derived, and the stability of the closed-loop control system is proved. Numerical simulations show the validity and feasibility of the theoretical results.     

Enhanced thermoelectric properties of atomic-layer-deposited Hf:Zn16O/18O superlattice films by interface-engineering

This study examines three novel approaches for enhancing the thermoelectric (TE) properties of atomic-layer-deposited (ALD) ZnO thin films: 1) Hf-doping, which preserved the crystallinity of ZnO and provided effective phonon scattering owing to Hf's similar atomic radius to and large mass difference with Zn, leading to high power factor (PF) and low thermal conductivity (κ); 2) controlling the distribution of Hf into an alternating scattered phase/clustered phase superlattice, which balanced the high PF of the scattered phases with the low κ of the clustered phases, while providing significant energy-filtering effect to raise the Seebeck coefficient; 3) introducing ¹⁸O/¹⁶O periodicity into the Hf:ZnO films—by alternately using H₂¹⁶O and H₂¹⁸O as oxidants in the ALD processes, which further suppressed κ without compromising PF. The combination of the three approaches resulted in a maximum improvement in ZT of ~1600% over that of the undoped ZnO.     

Cost-minimization analysis of a working vacation queue with N-policy and server breakdowns

This paper investigates the N-policy M/M/1 queueing system with working vacation and server breakdowns. As soon as the system becomes empty, the server begins a working vacation. The server works at a lower service rate rather than completely stopping service during a vacation period. The server may break down with different breakdown rates during the idle, working vacation, and normal busy periods. It is assumed that service times, vacation times, and repair times are all exponentially distributed. We analyze this queueing model as a quasi-birth–death process. Furthermore, the equilibrium condition of the system is derived for the steady state. Using the matrix-geometric method, we find the matrix-form expressions for the stationary probability distribution of the number of customers in the system and system performance measures. The expected cost function per unit time is constructed to determine the optimal values of the system decision variables, including the threshold N and mean service rates. We employ the particle swarm optimization algorithm to solve the optimization problem. Finally, numerical results are provided, and an application example is given to demonstrate the applicability of the queueing model.     

随车起重机伸缩臂截面多目标优化

为了提高某火箭炮弹药装填车随车起重机伸缩臂的结构刚度,减轻结构质量,建立了随车起重机伸缩臂参数化模型,并对伸缩臂在水平受载状态下进行仿真分析。以伸缩臂截面尺寸参数为设计变量,借助最优拉丁超立方试验设计建立样本空间,构造响应面多项式函数近似模型。在此基础上,利用NSGA-Ⅱ型遗传算法对伸缩臂自身重量、挠度进行多目标优化。优化结果表明:伸缩臂质量减轻了24.5%,减重效果明显。文中所采用的将参数化建模、有限元分析和数值寻优相结合的优化方法,可为起重机伸缩臂截面优化提供一定的参考。     

Bearing Failure Optimization of Composite Double-Lap Bolted Joints Based on a Three-Step Strategy Marked By Feasible Region Reduction and Model Decoupling

To minimize the mass and increase the bearing failure load of composite doublelap bolted joints, a three-step optimization strategy including feasible region reduction, optimization model decoupling and optimization was presented. In feasible region reduction, the dimensions of the feasible design region were reduced by selecting dominant design variables from numerous multilevel parameters by sensitivity analyses, and the feasible regions of variables were reduced by influence mechanism analyses. In model decoupling, the optimization model with a large number of variables was divided into various sub-models with fewer variables by variance analysis. In the third step, the optimization sub-models were solved one by one using a genetic algorithm, and the modified characteristic curve method was adopted as the failure prediction method. Based on the proposed optimization method, optimization of a double-lap single-bolt joint was performed using the ANSYS^® code. The results show that the bearing failure load increased by 13.5% and that the mass decreased by 8.7% compared with those of the initial design of the joint, which validated the effectiveness of the three-step optimization strategy.     

Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响

热轧态中锰TRIP钢首先经650 ℃退火2 h,随后在550 ℃进行等温时效热处理,采用场发射扫描电镜(FE-SEM)研究该钢中P的偏聚和时效析出行为的变化情况。结果表明,中锰TRIP钢中P在晶界的偏聚是一种非平衡偏聚现象,临界时间约为50 h,与理论计算结果48 h较为吻合。在局部偏聚区域内,C与P存在共偏聚的关系,即P偏聚量高的地方,C含量也高。而合金元素Nb具有抑制P偏聚的效果,在20~70 h时效时间内,可以相对降低6.57%~19.5%的最大P偏聚量。根据电子背散射衍射(EBSD)菊池线分析,P偏聚量低于2.28at%时,P为固溶状态,高于2.28at.%时,P为析出状态。     

基于改进人工蜂群算法的多目标绿色柔性作业车间调度研究

针对多目标绿色柔性作业车间调度问题（MGFJSP）的特点，提出从碳排放量、噪声和废弃物这3个指标来综合评定环境污染程度，建立了以最小化最大完成时间和环境污染程度为优化目标的MGFJSP模型，并提出了一种改进的人工蜂群算法来求解该模型。算法的具体改进包括：设计了一种三维向量的编码和对应解码方案，在跟随蜂搜索阶段引入一种有效的动态邻域搜索操作来提高算法的局部搜索能力，在侦查蜂阶段提出产生新食物源的策略用于增加种群的多样性。最后进行了实验研究与算法对比，以验证所建模型和所提算法的有效性。     

Experimental research on dynamic response of PZT-5H under impact load

In order to improve the stability of PZT-based sensors, the mechanical, dielectric, ferroelectric and piezoelectric properties of PZT-5H under impact load were studied experimentally by using the separated Hopkinson pressure bar (SHPB) with an electrical output measurement device. At the same time, the experimental study on the material properties of PZT-5H before and after the impact was carried out. The effect of impact cracks on the output voltage of PZT-5H was also analyzed. The results show that the dynamic piezoelectric constants of PZT-5H under low stress impact (10–50 MPa) are different from those under quasi-static state, and the empirical relationship between them and the peak stress is obtained through experiments. The dielectric properties of PZT-5H did not change under low stress impact, but micro-cracks occurred in the material and dielectric loss increased at high frequencies. Under short circuit, the residual polarization intensity of PZT-5H decreases sharply due to impact load. While the impact load causes the secondary polarization and the increase of the residual polarization intensity of PZT under open circuit. When the stress is over 45 MPa, the PZT-5H breaks. The formation of cracks causes abnormal discharge voltage and gap discharge.     

Use of conditioning time to investigate the mechanisms of interactions of selected fatty acids on hematite Part II laboratory investigations

It is the aim of this paper to examine the effects of conditioning time on the flotation of hematite using three technical grade fatty acid reagents as providing additional evidence on their mechanism of interaction with the hematite surface. Various mechanisms have been postulated as occurring as conditioning time is increased. Both physical (e.g. conditioning time and power input) and chemical (nature, dispersion and solubility of the adsorbing species) contribute to the mechanisms of attachment of collector. In this paper, the mechanism of attachment of oleate to hematite can be readily explained by chemisorption, but the mechanism of attachment of lauric acid appears to be physical adsorption at neutral pH. The flotation of hematite with a mixture of tallow-type fatty acids (palmitic, stearic and oleic acids) is very sensitive to conditioning time, and suggests that, even though flotation is very effective at short conditioning times, it is very susceptible to the presence of fines and their associated high surface areas. It is therefore obvious that both the physical and chemical conditions contribute to the mechanisms of adsorption of fatty acids on iron-containing oxide minerals and must be understood in order to optimise the flotation of these minerals in an industrial situation.     

An engineering method for complex structural optimization involving both size and topology design variables

This work presents an engineering method for optimizing structures made of bars, beams, plates, or a combination of those components. Corresponding problems involve both continuous (size) and discrete (topology) variables. Using a branched multipoint approximate function, which involves such mixed variables, a series of sequential approximate problems are constructed to make the primal problem explicit. To solve the approximate problems, genetic algorithm (GA) is utilized to optimize discrete variables, and when calculating individual fitness values in GA, a second-level approximate problem only involving retained continuous variables is built to optimize continuous variables. The solution to the second-level approximate problem can be easily obtained with dual methods. Structural analyses are only needed before improving the branched approximate functions in the iteration cycles. The method aims at optimal design of discrete structures consisting of bars, beams, plates, or other components. Numerical examples are given to illustrate its effectiveness, including frame topology optimization, layout optimization of stiffeners modeled with beams or shells, concurrent layout optimization of beam and shell components, and an application in a microsatellite structure. Optimization results show that the number of structural analyses is dramatically decreased when compared with pure GA while even comparable to pure sizing optimization.