MGD工艺技术的特点

应炼油厂要求，FCC既要多产柴油，又需多产液化气，石油化工科学研究院开发了MGD工艺。该工工艺遵循催化裂化的反应机理，把分段进料和汽油回炼紧密组合为一个体系，较好地达到了用掺渣油原料多产柴油和液化气的目的，其汽油烯烃和硫含量降低。从而使炼油厂调合汽油达到产品规格。工艺实施容易，改造投入少、见效快，受到炼油厂欢迎，并迅速推广应用。浅释了MGD工艺的反应机理，并提出了应用中应该注意的问题。     

热带城市垃圾典型组分的热解特性研究

对热带城市垃圾的几种典型组分进行了热解实验，得到了它们的失重曲线，通过对失重曲线进行分析，得到了这几种典型组分的热解规律，并通过建立热解动力学模型，求出了其中两种组分的活化能E和频率因子A。     

加氢润滑油基础油光安定性研究进展

加氢处理基础油与溶剂精制基础油相比具有硫、氮含量低，颜色浅，粘度指数高，挥发性低，饱和烃含量高，对添加剂的感受性好等优点。但是，加氢处理润滑油基础油的一个明显缺点就是其光安定性差，即在有氧条件下通过光照（有时也需加热），油品颜色加深、透明度变差，继而有絮凝物或沉淀生成。文章综述了国内外有关加氢润滑油基础油光安定性的原因和解决办法的研究进展情况。     

体积-表面淬火中加热温度的自动控制

根据表面-体积淬火奥氏体规范的要求，分析了感应加热过程中温度控制的特点和方式，并介绍了采用红外线光导纤维测温和微机控温技术成功用于体积-表面淬火中透热温度的自动控制。     

动态光散射法研究海藻酸钠凝胶松弛行为

在前文的基础上，用相关函数轮廓分析的方法剖析了运动模型模式的复杂性。通过海藻酸钠水溶液在０．１ｍｏｌ／ＬＣａＣｌ２水溶液透析凝胶化过程中交联网络的松弛时间谱表明它不是单一的峰，有两上特征运动模式，并随透析向更慢的运动模式发展，这很慢的运动模式估计与区域的结构的生成有关。     

Modeling of the bulk free radical polymerization up to high conversion—three stage polymerization model. II. Number-average molecular weight and apparent initiator efficiency

The equations for predicting the number-average molecular weight are derived on the basis of the three stage polymerization model (TSPM) in this paper. By applying the equations, a plotting approach is proposed to determine the apparent initiator efficiency defined as f[(α_td+1)/2] and the constant of chain transfer to monomer, where f is the initiator efficiency and α_td denotes the fraction of the termination rate constants by disproportionation. Using the approach to plot the experimental data in the literature, it is found that the chain transfer to monomer can be neglected for both methylmethacrylate (MMA) and styrene (St) polymerizations, but it can exert a significant effect on ethylmethacrylate (EMA) polymerization. In addition, the apparent initiator efficiency is found to be independent of reaction temperature and initiator concentration at each stage. The values of f[(α_td+1)/2] at gel effect stage are slightly reduced as compared with that at low conversion stage for MMA and EMA polymerizations. However, it decreases significantly at gel effect stage for St polymerization. Using the equations derived and the apparent initiator efficiencies obtained from TSPM plots, the number-average molecular weights at different conversions can be predicted. Comparisons show that the agreement between predictions and experimental data is satisfactory.     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002     

Thermally induced microstructural changes in cotton fibers: A free‐volume study

I measured positron lifetime in natural polymer–cotton fibers as a function of isochronal annealing temperature in the range 27–290°C. The variations in the positron results indicated structural changes occurring in the cotton fibers and determined the glass‐transition temperature as 80°C. Activation energies were measured separately for the crystalline and amorphous regions, indicating the versatility of the technique. These values were close to the O? H bond dissociation energy, suggesting O? H bond dissociation, the most probable process occurring under thermal treatment. As an extension of the positron results, the molecular weight of the cotton fibers was determined to be 1,200,000 based on free volume, which was within the range suggested for cotton. There seemed to be an indication that crosslinking changed the spiral structure of cotton fibers to the network type. However, this needs to be validated by other measurements. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3336–3345, 2002     

城市道路中的高杆照明

分析高杆照明的特点及其在城市道路中应用的实例，进而阐述高杆照明系统中主要参数的确定方法。