Crowding as an Agronomic Factor Determining the Development of Plants and the Productivity of Linseed (Linum usitatissimum L.)

ABSTRACT

Nine sowing densities of linseed were compared in a two-year experiment. Self-regulation of the density of a linseed stand resulted in a differentiated branching of the plants. The number of capsules on a linseed shoot, as well as seeds in the capsule, and the number of seeds from the shoot were highly varied from year to year, and there is even a stronger differentiation in the weight of 1000 seeds. Linear relationships were noted between the mass of seeds from the linseed plant and the number of capsules. The yield of linseed was affected by both factors. An increasing sowing rate reduced the seed yield from the shoot and the plant. At lower seeding rates, the lateral shoots contributed in the seeds yield of the plant to a higher degree compared to the main ones.     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

不同工质回路热管负载功率变化下的质量流量特性

为了进一步提高回路热管仿真精度并丰富回路热管实验研究方法，本文对回路热管瞬态传质进行实验研究。使用高精度质量流量计分别对以丙酮、乙醇、丙烯为工质的回路热管进行不同负载功率下的质量流量测量研究。结果表明：启动阶段，热负载10W时，丙烯回路比丙酮回路热管启动快，且两者的温度稳定均滞后于质量流量；稳定阶段，随着热负载功率增大，不同工质的回路热管的平均质量流量均线性增长，而瞬态质量流量则持续波动，其质量流量波动幅度均呈现先减小后增大的趋势。质量流量波动幅度会受到气体工质的可压缩性与作用在毛细芯内部上的热量的共同影响。通过频谱分析发现，液相质量流量波动还会受到冷凝器两相区的影响。高热负载下，作用在毛细芯内部上的热量占主导地位，质量流量波动加剧，同时出现周期性大幅波动，且其波动频率随着热负载增大而增大。     

复杂炼油塔模拟的改进联立方程内外层算法

在内外层算法的基础上，采用联立方程思想将主塔、侧线汽提塔视为一个整体进行建模，并针对复杂炼油塔的特点对算法提出了改进。首先，由于传统内外层法简化的K值模型对组成的变化不敏感，在处理带有石油的体系时，容易出现迭代次数较多，甚至部分塔板温度更新异常的问题，因此采用了汽相分数加和式推导了简化的K值模型加权因子。其次，借鉴流量加和法思想，规定侧线汽提塔的塔底产品流量作为设计变量，增强了算法收敛的稳定性。为验证改进后算法的有效性，采用不同的算法对实际的常压塔进行了模拟，结果显示改进后的算法适合应用于复杂炼油塔的模拟计算。     

变形铝合金表面锆基化学转化膜的研究现状

化学转化膜是金属表面主要的处理方法之一，具备良好的附着力和耐蚀性，能为铝合金提供一定的临时防护。传统的六价铬酸盐化学转化膜在日渐严苛的环保压力下已经逐渐淘汰，取而代之的是近几年发展迅猛的三价铬及无铬锆基化学转化膜。铝合金可分为铸造铝合金和变形铝合金，按照所含主要合金元素和热处理状态可分为若干个系列和型号。本文选取几种典型的变形铝合金，综述了不同铝合金微观组织对转化膜成膜过程的影响，化学转化液添加剂、预处理和后处理工艺对转化膜性能的调控及作用机理，以及几种典型商业钝化剂在变形铝合金表面的应用。总结了目前变形铝合金表面锆基化学转化膜仍面临的问题和发展趋势，未来化学转化膜需在满足新型铝合金发展要求的基础上，通过不同有机、无机添加剂以及外场作用对转化膜的成膜均一性、完整性进行调控，以提高转化膜的综合性能。     

溶液浓差能驱动的逆电渗析反应器制氢实验研究

低品位热能制氢技术首先是将热能转换为溶液浓差能，然后通过逆电渗析（RED）反应器将溶液浓差能转换成氢能。为了验证RED反应器能将溶液浓差能转换为氢能，探索关键运行参数变化对能量转换过程的影响。设计了一个由40个膜对所构成的RED反应器，以NaCl水溶液为工作溶液，NaOH水溶液为电极液的制氢系统。通过改变浓/稀溶液入口浓度，溶液过膜流速以及输出电流来考察对RED反应器产氢率、制氢效率和能量转换效率的影响。实验结果发现，浓/稀溶液入口浓度，过膜流速变化均会影响RED反应器的输出电流。在外电路短接条件下，输出电流越大，反应器产氢率和制氢效率越高，但能量转换效率越低。     

压水堆核电厂一回路首次钝化工艺研究

压水堆核电厂热态功能试验中的一回路首次钝化对核电厂一回路材料腐蚀控制和减少腐蚀产物等方面具有重要作用。本文结合理论研究与工程实际情况，提出了在热态功能试验过程中钝化膜的生成包含电化学反应和化学反应的观点，阐述了双层膜的生长机理，解释了用电化学测试方法分析钝化工艺过程的合理性，推导出钝化温度与钝化膜反应速率的函数关系式，钝化温度升高，反应速率升高，钝化时间缩短；明确了钝化工艺温度的理论限值应不低于260℃。      

压水堆核电厂堆外源量程探测器计数率分析

压水堆核电厂启动过程中，次级中子源为堆外源量程探测器提供本底计数率，避免测量盲区，确保反应堆安全启动。但次级中子源的引入会为核电厂带来较大的经济和环境负担，同时也需承受次级中子源破损等带来的风险。为此，可使用受辐照燃料组件的自发裂变中子源进行替代，即无源启动方式。通过研究堆外源量程探测器计数率的理论计算方法，并基于运行电厂测量数据进行分析验证，为源量程探测器计数率的理论预估提供了较为完善的理论方法流程。本文结果可为无源启动源量程探测器计数率分析提供支持，同时也可用于次级中子源装载量或布置位置的优化分析等。     

Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

生物质纤维和改性木质素对聚乳酸结晶性能的影响

采用改性木质素(MZS)作为成核剂,生物质纤维(BF)作为增强剂,通过双螺杆挤出机制备了生物降解的聚乳酸(PLA)/BF/MZS材料。采用差式扫量热仪(DSC)、电子万能试验机和扫描电子显微镜(SEM)分析了BF和MZS对PLA材料性能的影响。结果表明,BF和MZS有效提高了PLA的结晶能力和力学性能。当BF和MZS的含量分别为15%和1%时,PLA材料结晶度提高至67.1%,在50℃/min降温速率下仍具有较高的结晶能力。105℃等温结晶时,15%BF和1%MZS的PLA材料半结晶时间降低至9.0 s,比纯PLA缩短了72.2%。当PLA含有3%BF和1%MZS时,拉伸强度和冲击强度分别为70.1 MPa和7.4 kJ/m^2,比纯PLA分别提高了7.8%和10.4%,根据SEM显示,当BF含量为3%时,在PLA材料中分布较均匀。