Polyaniline-based networks combined with Fe3O4 hollow spheres and carbon balls for excellent electromagnetic wave absorption

Polyaniline (PANI)-based networks combined with Fe₃O₄ hollow spheres and carbon balls (FCP) for improved electromagnetic wave (EMW) absorption were investigated using an easy-to-industrialize solvothermal and physical method. Hollow structure Fe₃O₄ spheres with a lower density than that of the common solid sphere were prepared. As a thin and light magnetic material, Fe₃O₄ hollow spheres generate magnetic loss, carbon balls and PANI networks generate dielectric loss. The magnetic and conductive parts play appropriate roles in achieving complementarity in the EMW absorption. The relatively high specific surface area introduced by PANI networks promotes interfacial polarization and further supports dielectric loss. In conclusion, the above reasons provide multiple attenuation mechanisms. Samples FCP1 (?65.109 dB, at 12.800 GHz, 1.966 mm, from 5.6 to 18.0 GHz) and FCP2 (?61.033 dB, at 8.480 GHz, 3.328 mm, from 4.3 to 18.0 GHz) demonstrated a wide bandwidth, a small thickness, a minimum reflection loss (R_L), and a low loading ratio (25%) in paraffin-based composites. Specifically, their loading ration of 25% is much lower than the loading ratio of conventional materials (usually 50% and above). In addition, the bandwidth is excessively wide, above 12 GHz, possessing good absorption performance in continuous intervals with different thicknesses. Such excellent characteristics have rarely been reported in literature.     

Corrosion behavior of under‐, peak‐, and over‐aged 6063 alloy: A comparative study

The mechanical property of age‐hardenable Al‐alloys is governed by the state of ageing, which determines the microstructure and consequently, their corrosion behavior which is a vital aspect for a number of applications. This article presents a comparative assessment of corrosion behavior of under‐, peak‐ and over‐aged Al‐Mg‐Si alloy. Corrosion characteristics have been determined via immersion tests in 0.1 M ortho‐phosphoric acid solution and intergranular corrosion (IGC) tests. Corroded surfaces are examined by field emission scanning electron micrographs‐energy dispersive spectroscopy and 3D optical profilometer. The obtained results reveal that the corrosion rate at a specific immersion time as well as the depth of IGC increases in the order for under‐, peak‐, and over‐aged states. Irrespective of the state of ageing, corrosion loss increases linearly but the rate of corrosion decreases rapidly with increasing immersion time. The dominant mode of corrosion in under‐aged alloy is identified as localized pitting, while peak‐aged is highly susceptible to IGC in contrast extensive pitting corrosion is observed for over‐aged alloy. The observed differences in corrosion behavior are explained considering characteristics of precipitates. Formation of β (Mg₂Si) in case of over‐aged alloy and presence of inclusions like AlFeMnSi particles are found to accelerate pitting corrosion.     

Maximum Data Generation Rate Routing Protocol Based on Data Flow Controlling Technology for Rechargeable Wireless Sensor Networks

For rechargeable wireless sensor networks, limited energy storage capacity, dynamic energy supply, low and dynamic duty cycles cause that it is unpractical to maintain a fixed routing path for packets delivery permanently from a source to destination in a distributed scenario. Therefore, before data delivery, a sensor has to update its waking schedule continuously and share them to its neighbors, which lead to high energy expenditure for reestablishing path links frequently and low efficiency of energy utilization for collecting packets. In this work, we propose the maximum data generation rate routing protocol based on data flow controlling technology. For a sensor, it does not share its waking schedule to its neighbors and cache any waking schedules of other sensors. Hence, the energy consumption for time synchronization, location information and waking schedule shared will be reduced significantly. The saving energy can be used for improving data collection rate. Simulation shows our scheme is efficient to improve packets generation rate in rechargeable wireless sensor networks.     

渣油催化临氢热转化钼铁双金属催化剂的研究

Replacement of precious single metal catalysts with cost-effective, highly-dispersed composite catalysts for catalytic hydrothermal conversion of residue holds tremendous promise for the residue upgrading technologies. Organic metals were added to the feed as the oil-soluble precursors, and transformed into the catalytic active phases in this work. Physical properties and structures of the composite catalysts had been investigated by X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, scanning electron microscope and transmission electron microscopy. The composite catalysts were found to be highly efficient in the catalytic hydrothermal conversion of both model compound and residue. Increased metal dispersion and synergistic effects of two metals played indispensable roles in such catalytic system. Results showed that under the test conditions in the article, the catalyst had the best catalytic performance when the mass ratio of molybdenum to iron was 1.5.     

On the capacity of the state‐dependent interference relay channel

This paper considers the state‐dependent interference relay channel (SIRC) in which one of the two users may operate as a secondary user and the relay has a noncausal access to the signals from both users. For discrete memoryless SIRC, we first establish the achievable rate region by carefully merging Han‐Kobayashi rate splitting encoding technique, superposition encoding, and Gelfand‐Pinsker encoding technique. Then, based on the achievable rate region that we derive, the capacity of the SIRC is established in many different scenarios including (a) the weak interference regime, (b) the strong interference regime, and (c) the very strong interference regime. This means that our capacity results contain all available known results in the literature. Next, the achievable rate region and the associated capacity results are also evaluated in the case of additive Gaussian noise. Additionally, many numerical examples are investigated to show the value of our theoretical derivations.     

Forging furnace with thermochemical waste-heat recuperation by natural gas reforming: Fuel saving and heat balance

This paper considers thermochemical recuperation (TCR) of waste-heat using natural gas reforming by steam and combustion products. Combustion products contain steam (H₂O), carbon dioxide (CO₂), and ballast nitrogen (N₂). Because endothermic chemical reactions take place, methane steam-dry reforming creates new synthetic fuel that contains valuable combustion components: hydrogen (H₂), carbon monoxide (CO), and unreformed methane (CH₄). There are several advantages to performing TCR in the industrial furnaces: high energy efficiency, high regeneration rate (rate of waste-heat recovery), and low emission of greenhouse gases (CO₂, NO_x). As will be shown, the use of TCR is significantly increasing the efficiency of industrial furnaces – it has been observed that TCR is capable of reducing fuel consumption by nearly 25%. Additionally, increased energy efficiency has a beneficial effect on the environment as it leads to a reduction in greenhouse gas emissions.     

High-rate capability of carbon-coated micron-sized hexagonal TT-Nb2O5 composites for lithium-ion battery

With excellent specific capacity, superior cycle stability, safety and strong practical, Nb₂O₅ has been considered as one of the prospective anode materials for lithium-ion batteries (LIBs). However, current study suggests that Nb₂O₅ electrode materials for LIBs still face the vital issues of low electrical conductivity and poor rate performance. Therefore, carbon-coated TT-Nb₂O₅ materials are designed and synthesized through solid state method in this work, which present high specific capacity (228 mA h g^?1 at 0.2C), satisfactory rate properties (107 mA h g^?1 at 20 C). The outstanding electrochemical property can not only give the credit to the pseudocapacitance effect of TT-Nb₂O₅, but also attribute to introduction of carbon. The homogeneous carbon-coated materials enhance the electrical conductivity, increase the electron transmission speed and alleviate particle crushing. This research not only offers a new method for preparing excellent electrode materials, but also provides a kind of excellent anode material with prospective application for LIBs.     

Lignin from Annual Plants as Raw Material Source for Flavors and Basic Chemicals

The enzymatic conversion of lignins, possibly in combination with electrochemical oxidation, makes aromatics such as syringol, guaiacol, vanillin and catechol available in the qualities required by the fragrance industry. The lignins were obtained by soda digestion from wheat straw and Miscanthus, characterized and then converted with laccases. The overall yield amounted up to 9 wt % with a product spectrum confined to four substances. Catechol was the major product, with a fraction of ≈75 %. It can easily be isolated by extraction with acetone.     

Research on the identification performance of UHF RFID system considering the correlation of cascaded channel

The identification rate of UHF RFID system was restricted by multipath propagation effects.The system identification performance was studied considering the correlation coefficient between forward and reverse channels.Based on the generalized Rician fading channel model,the analytical expression of identification rate was derived under independent,full correlation and correlation cases.Compared with the existing analysis,the proposed uniform calculation formula of identification rate was for any correlation coefficient and kinds of channel conditions.The numerical computation and Monte-carlo simulations show that the influences of different correlation coefficients,channel conditions,sensitivity and distance on the identification rate.     

Preventive replacement policies with time of operations,mission durations,minimal repairs and maintenance triggering approaches

When a mission arrives at a random time and lasts for a duration, it becomes an interesting problem to plan replacement policies according to the health condition and repair history of the operating unit, as the reliability is required at mission time and no replacement can be done preventively during the mission duration. From this viewpoint, this paper proposes that effective replacement policies should be collaborative ones gathering data from time of operations, mission durations, minimal repairs and maintenance triggering approaches. We firstly discuss replacement policies with time of operations and random arrival times of mission durations, model the policies and find optimum replacement times and mission durations to minimize the expected replacement cost rates analytically. Secondly, replacement policies with minimal repairs and mission durations are discussed in a similar analytical way. Furthermore, the maintenance triggering approaches, i.e., replacement first and last, are also considered into respective replacement policies. Numerical examples are illustrated when the arrival time of the mission has a gamma distribution and the failure time of the unit has a Weibull distribution. In addition, simple case illustrations of maintaining the production system in glass factories are given based on the assumed data.