Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Hydrogen Absorption and Release Behavior in Hydrogen Decrepitation Process of Nd-Fe-B Alloys

The behavior of hydrogen absorption and release in hydrogen decrepitation (HD) process of Nd-Fe-B alloys were investigated. The results reveal that the reactivity and the amount of hydrogen absorption in HD process are related to the surface activity of the alloy so that the fresh and active surface has a higher efficiency. The presence of Nd-rich phase at the grain boundary is an essential factor of the HD activity of the alloy at room temperature. On degassing, hydrogen is released from the HD powder continuously with increasing temperature. And the residual hydrogen is as low as 0.0015% at 1073K, which shows that the hydrogen is almost exhaused. It is feasible to remove the hydrogen from the HD powder by heating treatment at the temperature of 523-723K for 1h prior to the magnetic field forming in order to decrease the harmful effect of hydrogen on the easy axis alignment of HD magnet.     

鱼雷罐喷粉预处理过程水模研究

在鱼罐喷粉预处理水模实验数据的基础上，进一步利用线性回归确定各工艺操作参数对喷吹基本参数（均混时间、粉剂穿透比和粉剂停留时间）的影响，得出各传输动力学基本参数的函数关系式。     

东海盆地西南部地质特征与油气分布探讨

本文根据近3×10~4km地震和13口探井及其它地球物理、地质等方面资料,综合分析认为:东海盆地西南部与盆地其它部分在发育演化、构造运动、沉积环境等方面差异甚大。 盆地西南部(杭州湾—冲绳岛断裂以南地区)发育演化经历了断陷—坳陷—隆起—铺盖四个阶段。始新世末期的隆起在研究区演化史上有15～20Ma的沉积间断、剥蚀。这段历程,盆地其它部分未曾经历。其次是区内始新世末期抬升运动,致使始新统及以下老地层受剥蚀,仅始新统最大剥蚀量达1000m,这是盆地内绝无仅有的。第三是第三纪以海相沉积环境为主,特别在始新世,为海侵高潮,海城宽阔达8000km~2,这时盆地东北部正接受陆相沉积。研究区中部(北东向)可能存在超压泥岩及多套生油岩系,应为有利生油气区。研究区可能是盆地最有油气远景地区之一。     

纳米β-Ni(OH)2与球型Ni(OH)2的热性能比较研究

用配位沉淀法合成出纳米级Ni（OH）2，并对其进行XRD，TEM，DSC分析，分析结果表明，所得纳米β-Ni（OH）2为可用作电极材料的β-Ni（OH）2，粒径为30－40nm，且热分解温度比普通球镍低10℃左右，摩尔分解热比普通球镍低4－7kJ，从理论上分析了产生此现象的原因。     

石英砂物料气流冲击粉碎效果影响因素分析

通过对石英砂物料在不同实验条件下的粉碎结果分析，论述了流化床式超细气流粉碎机工艺参数对产品粒度的影响。     

激光法合成SiC超细粉末物理化学过程的研究——Ⅰ.实验规律及粉末特性

用50W连续波CO_2激光器为热源,诱发SiH_4和C_2H_4反应,合成SiC超细粉末。实验确定了反应腔体内压力p、气源中的C/Si原子比、喷嘴内径2r以及激光功率密度与粉末特性之间的关系,并对合成的产物进行物理、化学表征。     

高强度烧结钢

为开拓粉末冶金材料新的应用领域，近年来对高强度烧结钢进行了大量的研究与开发。本文简要介绍Ｈｏｇａｎａｓ公司开发的一些高强粉末冶金材料及对一些高强度烧结材料尺寸变化的控制。     

超细铁粉和氧化铁颗粒的研究

用透射电镜和图像分析仪等研究了超细铁粉和γ-Fe_2O_3粉末的结构、形貌、粒子的平均尺寸以及粒度分布。研究结果表明,多数超细铁粉粒子近似呈球形,并且,铁粉粒子由两相组成,粒子的核心部分是金屑a-Fe,表面的包裹层为氧化物层,它由Fe_3O_4和7-Fe_O_3的混合物组成。氧化层的平均厚度大约占整个粒子直径的20％左右。羰基铁粉粒子(含氧化层)的平均直径为16nm。直径在4～24nm范围的粒子数占总粒子数的91％,而7-Fe_2O_3粉末既有雪茄状粒子,也有小球状粒子。分析表明,球状粒子的平均直径为113nm,雪茄状粒子的平均直径(按<长 宽>/2计算)为148nm。由于超细铁粉粒子很细,且有磁性,制备电镜试样时分散比较困难。本文比较了几种分散方法后,使用了一种较好的分散方法——超声喷管分散法。     

TiO_2粉体性能对PTC热敏电阻性能的影响

ＴｉＯ_２的纯度、粒度及粒形对ＢａＴｉＯ_３系ＰＴＣＲ的性能影响很大，对所用ＴｉＯ_２加以选择非常重要，国产和日本产ＴｉＯ_２原料在粉体性能上存在差异。