不同工质回路热管负载功率变化下的质量流量特性

为了进一步提高回路热管仿真精度并丰富回路热管实验研究方法，本文对回路热管瞬态传质进行实验研究。使用高精度质量流量计分别对以丙酮、乙醇、丙烯为工质的回路热管进行不同负载功率下的质量流量测量研究。结果表明：启动阶段，热负载10W时，丙烯回路比丙酮回路热管启动快，且两者的温度稳定均滞后于质量流量；稳定阶段，随着热负载功率增大，不同工质的回路热管的平均质量流量均线性增长，而瞬态质量流量则持续波动，其质量流量波动幅度均呈现先减小后增大的趋势。质量流量波动幅度会受到气体工质的可压缩性与作用在毛细芯内部上的热量的共同影响。通过频谱分析发现，液相质量流量波动还会受到冷凝器两相区的影响。高热负载下，作用在毛细芯内部上的热量占主导地位，质量流量波动加剧，同时出现周期性大幅波动，且其波动频率随着热负载增大而增大。     

Adaptive GLR-, Rao- and Wald-based CFAR detectors for a subspace signal embedded in structured Gaussian interference

The problem of detecting a subspace signal embedded in subspace Gaussian interference and thermal noise is studied in this paper. In this problem, both the signal-independent and signal-dependent interferences are assumed to be present, therefore the overall interference subspace covers the signal subspace. The approach of this paper extends previous works involving either of those two kinds of interferences. A set of secondary data containing only interference plus noise is employed to estimate the interference covariance matrix and the noise power. Three new detectors are designed via the generalized likelihood ratio (GLR), Rao and Wald tests, respectively. Their probabilities of false alarms (PFAs) and detections are analytically derived. The PFAs show that the new detectors have the constant false alarm rate (CFAR) property against the interference and noise. Numerical results show that the new detectors outperform their counterparts for the studied problem. Furthermore, the new detectors are less sensitive to the secondary data size and to the mismatched subspace signal than some other detectors, such as the GLR detector (GLRD), the adaptive matched filter (AMF), the adaptive subspace detector (ASD), etc.     

蛋类礼盒包装结构的缓冲性能研究

目的研究蛋类礼盒包装结构的缓冲性能。方法以蛋类尺寸为基础,建立可发性聚乙烯(expandable polyethylene. EPE)缓冲单元结构和组合结构,进行静态仿真分析和实验验证,比较结构在形状、叠合层数、组合形式等参数变化时的载荷与位移。结果结构层数变化相同时,单元结构的极限载荷从143N增加到236 N,组合结构的极限载荷从224 N增加到476 N,均呈近线性增长。结论蛋类礼盒包装中,组合结构的承载能力优于单元结构,通过单元结构的组合,可满足不同蛋类的包装要求。     

改进Elman神经网络在短期热负荷预测中的应用

热电厂的短期热负荷预测在城市集中供暖中起着至关重要的作用,直接影响热电厂的经济效益和热能利用率。电厂的短期热负荷一般采用神经网络预测模型进行预测,而BP神经网络应用最为广泛。Elman神经网络算法在BP神经网络基础上加入了承接层,作为一步延时算子,实现记忆能力,使系统具备适应时变能力,增强系统全局稳定性。但Elman神经网络算法模型的构造依然需要大量样本的支撑,而且输入层的变量多,导致预测时间依然很长,收敛速度慢。该文在Elman神经网络预测前,进行了相关系数预处理和对样本中异常值的平均化预处理,通过数据归一化运算,使Elman神经网络输入层变量大幅减少。仿真实验表明,改进的Elman神经网络算法使预测模型快速寻优,减少预测时间的同时明显提高预测精度。     

少量有机碳对单级自养脱氮工艺性能的影响

采用序批式生物膜反应器(SBBR),经过4个阶段的培养,快速富集好氧氨氧化细菌(AOB)和厌氧氨氧化细菌(AnAOB),并考察不同低碳氮比对工艺脱氮性能的影响。结果表明,NH4^+-N去除率可达到99%以上,TN去除率可达到90%以上。对应C/N=0、1和2时,反应器出水NH4^+-N和TN去除率分别为99.59%、99.5%、98.47%和93.75%、97.22%、98.11%。说明少量COD的存在,可实现同步硝化-厌氧氨氧化-反硝化,且在一定程度上提高脱氮效率。     

汽轮机转子钢断裂韧度试验方法的研究

采用载荷分离法和多试样法对汽轮机某高压转子钢材料在高温下的断裂韧度值进行了测试,讨论了载荷分离法测断裂韧度的可靠性,并与传统的多试样法进行了对比。     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。     

全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

Strain hardening behaviors and mechanisms of polyurethane under various strain rate loading

The uniaxial tension experiments are performed on thermoplastic polyurethane to investigate its mechanical behaviors and related potential mechanisms, and the loading strain rate is designing to be wide ranging from 0.0001 to 1 s⁻¹. It is found that the polyurethane presents an obvious rate-dependence, and the stress strain curves share distinct strain hardening characteristics under the investigated strain rates. Furthermore, the strain hardening ratios are sharing nearly same trends and appear to be influenced by both strain rate and the induced adiabatic heating. Besides, the ratio is also strain-dependent on previous loading history. Then, a two-dimension unit cell model is built to investigate potential equivalent mechanisms, of which the hard phase as inclusion is equivalent with crystallization zone, crosslinking sites, and so forth. The simulation results facilitate to explain the distinct strain hardening ratios, even for the matrix from the extrapolated curves under super-low strain rate loading. Finally, the analogic mechanisms of equivalent hard inclusions are proposed, which can reasonably explain the strain rate- and strain-dependence characteristics of polyurethane mechanical behaviors.