基准平面垂直断面法在爆破漏斗试验中的应用

系统阐述了基准平面垂直断面法在爆破漏斗试验中测量爆破漏斗体积的基本原理,并将隧道激光断面仪应用于金厂河矿1 750 m水平15^#采场底部切割巷道爆破漏斗试验爆破漏斗体积测量中。通过与传统体重法等计算法所得漏斗体积分析比较,结果表明基于隧道激光断面仪与3D Mine软件分析的基准平面垂直断面法实用性强、操作方便、结果直观可靠,达到试验预期目的。     

珠江口盆地珠一坳陷古近系高自然伽马砂岩形成机制及油气地质意义

运用放射性元素寻找油气是一种非常规油气勘探手段。近年来,在珠江口盆地珠一坳陷富烃凹陷周边古近系钻遇高自然伽马(GR)砂岩,其GR值(100~300 API)甚至大于同区泥岩的GR值(100~200 API)。为了弄清该特殊现象背后的地质意义,对珠江口盆地珠一坳陷古近系高自然伽马砂岩开展了铀(U)、钍(Th)、钾(K)等3种元素含量与GR值的相关趋势线分析,从井震特征、岩性特征及矿物成分特征等入手分析了砂岩GR值增高的主要原因及成因机制,探讨了放射性元素聚集的条件、运移通道、驱动力以及油气意义。结果表明:西江、惠州地区由U含量增高导致砂岩GR值偏高,恩平、番禺地区由K,Th含量增高导致砂岩GR值偏高;砂岩GR值增高有两大成因机制,一是地下流体带来的放射性元素离子U4+在氧化-还原面处富集后导致地层GR值偏高,这种特殊现象说明在具有连通基底大断裂旁的圈闭中,U4+的富集指示了曾经油气的存在,证实了研究区油气运移通道的有效性,对于油气藏的预测有着非常重要的指导性意义,二是地表流体带来的含放射性元素的矿物大量沉积后导致地层GR值偏高,含放射性元素矿物性质不稳定,可指示近源供给的存在,对于判断物源及沉积环境有着非常重要的意义。该研究成果为预测研究区油气成藏有利区带提供了依据。     

水压爆破拆除超大容积水池

简要介绍了组合式超大容积（８５０ｍ３）水池在水压爆破拆除过程中爆破方案选择、参数选取等方面的经验，并对爆破效果进行了分析，为同类工程施工提供了可借鉴的经验。     

Influence of SiC microstructure on its corrosion behavior in molten FLiNaK salt

The influence of the microstructure on the corrosion rate of three monolithic SiC samples in FLiNaK salt at 900 °C for 250 h was studied. The SiC samples, labeled as SiC-1, SiC-2, and SiC-3, had corrosion rates of 0.137, 0.020, and 0.043 mg/cm²h, respectively. Compared with grain size and the presence of special grain boundaries (i.e., Σ3), the content of high-angle grain boundaries (HAGBs) appeared to have the strongest influence on the corrosion rate of SiC in FLiNaK salt, since the corrosion rate increased six times as the concentration of high-angle grain boundaries increased from 19 to 32% for SiC-2 and SiC-1, respectively. These results stress the importance of controlling the content of HAGBs during the production process of SiC.     

Mixing enhancement mechanism of combined H2–Water jets in supersonic crossflows in a combustor with an expanded section

To obtain the mixing enhancement mechanism of H₂–Water combined jets in supersonic crossflows in a combustor with expanded section for rotating detonation ramjet, the flow field shape and spray structure were studied by experimental and numerical methods. The Eulerian–Lagrangian method was used to investigate the diffusion mechanism and H₂–Water interaction law of combined jets with different sequences. At the same time, high-speed photography and the schlieren technique were used to capture the flow field. The effects of jet pressure drop, orifice diameter, orifice spacing, incoming Mach number, and other parameters on the penetration depth of water jets were studied. The results of experiment and simulation show that using H₂–Water combined jets, the penetration depth of the jet spray can be greatly increased and the jet mixing effect can be significantly improved, which will contribute to the engine's ignition and stable combustion. In the case of pre-water/post-H₂, the penetration depth of the hydrogen jet is greater. In the case of pre-H₂/post-water, the hydrogen jet raises the water spray mainly by protecting the integrity of the water column.     

Categorical observers for metamerism

A method is proposed to generate categorical colour observer functions (individual colour matching functions) for any field size based on the CIE 2006 system of physiological observer functions. The method combines proposed categorical observer techniques of Sarkar et al with a physiologically-based individual observer model of Asano et al and a clustering technique to produce the optimal set of categorical observers. The number of required categorical observers varies depending on an application with as many as 50 required to predict individual observers' matches when a laser projector is viewed. However, 10 categorical observers are sufficient to represent colour-normal populations for personalized colour imaging. The proposed and recommended categorical observers represent a robust and inclusive technique to examine and quantify observer metamerism in any application of colorimetry.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Improved error performance for generalised spatial modulation with enhanced spectral efficiency

The existing analytical average bit error rate (ABER) expression of conventional generalised spatial modulation (CGSM) does not agree well with the Monte Carlo simulation results in the low signal‐to‐noise ratio (SNR) region. Hence, the first contribution of this paper is to derive a new and easy way to evaluate analytical ABER expression that improves the validation of the simulation results at low SNRs. Secondly, a novel system termed CGSM with enhanced spectral efficiency (CGSM‐ESE) is presented. This system is realised by applying a rotation angle to one of the two active transmit antennas. As a result, the overall spectral efficiency is increased by 1 bit/s/Hz when compared with the equivalent CGSM system. In order to validate the simulation results of CGSM‐ESE, the third contribution is to derive an analytical ABER expression. Finally, to improve the ABER performance of CGSM‐ESE, three link adaptation algorithms are developed. By assuming full knowledge of the channel at the receiver, the proposed algorithms select a subset of channel gain vector (CGV) pairs based on the Euclidean distance between all CGV pairs, CGV splitting, CGV amplitudes, or a combination of these.     

Risk of slaughterhouse workers developing work-related musculoskeletal disorders in different organizational working conditions

Job rotation is defined as workers rotating between tasks with different exposure levels and occupational demands. The aim of the present study was to analyze the risk factors for the development of upper-limb work-related musculoskeletal disorders (UL-WMSDs) in poultry slaughterhouse workers as well as compare the score of the OCRA Checklist in different organizational working conditions. In this cross-sectional study, 118 workers were involved, 68 women (32.3 ± 10.7 years) and 50 men (29.5 ± 10.5 years). Three organizational configurations (“without job rotation”, “with job rotation – tasks >1h” and “with job rotation - tasks <1h”) were evaluated using the OCRA Checklist method, totaling 36 tasks and 28 job rotation schemes composed of 2–3 tasks. The OCRA score of the right upper limbs (17.8 ± 3.2) was significantly higher (p = 0.046) relative to the left upper limbs (16.4 ± 3.6). The median score was significantly lower in the “with job rotation - tasks <1h” condition (18.6) when compared to the “job rotation – tasks >1h” (19.4) (p < 0.001) and the “without job rotation” (19.0) (p = 0.038) conditions. However, there was no significant difference between the condition “with job rotation - tasks >1h” and “without job rotation” (p = 0.155). Thus, job rotations with intervals <1h reduced the risk of developing UL-WMSDs. Job rotations with <1 h intervals in poultry slaughterhouses are recommended along with further studies to verify the effectiveness of rotations with more than two tasks, involving mild or non-repetitive tasks.