非稳定井流模型的半解析解

为了提高非稳定渗流计算的计算精度 ,通过数学分析得到了水位传导系数随时间变化时 ,一类非稳定渗流井流模型的半解析解 ,并进行了计算比较     

钻机用集成化液压源的研制

针对当前钻机液压配套设备越来越多的趋势,研制了集成化液压源。集成化液压源不是把原有的几个液压源的叠加组合,而是实现了液压源电气就地控制和远程控制、流量集中控制分配,压力集中控制,形成多种输出流量、多级输出压力和多个输出端口。     

井下注剂用小直径管起下装置的研制

针对目前国内小直径管井下注剂设备配套工具不完整,不能满足现场使用要求的情况,研制了井下注剂用小直径管起下装置。该装置采用可正反向旋转的液马达驱动主轴的方案,通过同步齿轮带动链条,夹紧机构使链条上的夹块夹住小直径管,由液压系统实现整个操作与控制,从而使装置上下运动。井场模拟试验表明,井下注剂用小直径管起下装置可完全满足小直径管起下作业的要求,且可避免小直径管管体的变形和损坏。     

液力联轴器喷油着火事故的原因分析及预防

以矿用液力联轴器为研究对象 ,阐明其喷油着火的机理 ,分析其喷油着火的原因并作出事故树分析 ,针对现场使用的情况 ,提出预防措施及发展趋势 ,对矿井安全生产具有指导性作用。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

液压伺服马达拖动研究

液压伺服马达拖动和液压伺服加载 ,目前列为液压技术研究的前缘学科。本文专门从液压伺服马达进行探讨。     

飞机液压系统污染及控制

本文全面分析了收音机液压系统污染的危害和主要原因，并在此基础上有针对性地提出了预防措施。     

淹没水跃的数值模拟

本文通过求解时均N－S方程κ－ε紊流模型，数值模拟了淹没水跃由静止到最终稳定的全过程。采用隐式非正交同位网格有限体积法离散控制方程组，利用动网格技术跟踪自由表面，并由Orlanski开边界条件得到无反射的出口边界。文中给出了淹没水跃在不同时刻自由表面形状、内部流场结构和流速矢量的变化情况，并与试验资料进行了比较。结果表明，本文方法能够准确有效地描述淹没水跃这类复杂自由表面流动的紊动特性。     

液压支柱表面镀层改进之探讨

通过比较电镀硬铬和化学镀镍在液压支柱表面处理上的应用 ,探讨了化学镀镍在配方、工艺、设备、镀层性能、环保等方面的优越性。     

液压集成块校核软件的编制和应用

本文叙述了液压集成块校核软件的编制思想和方法，并重点介绍了编制过程中所使用的相关技术，同时给出部分源程序。