Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

A conceptualization of intended learning outcomes supporting self‐regulated learners in indicating learning paths

Intended learning outcomes (ILOs) indicate what learners will be able to achieve after they are taught. Traditionally, ILOs are expressed as plain text or unstructured documents. What if all ILOs of a specific course of study can be conceptualized through a structured diagrammatic technique? It was hypothesized that learners can benefit from this conceptualization in learning, especially in self‐regulated learning. The aim of this study was to investigate whether the ILOs represented in unstructured or structured formats can facilitate learners to identify learning paths. The results revealed that the mean ratings of all learning paths were statistically significantly higher with structured ILOs.     

基于二元水循环的水量-水质-水效联合调控模型开发与应用

为将我国最严格水资源管理制度的实践与二元水循环理论相结合，提高“三条红线”控制指标的科学性与合理性，本文以SWAT模型为基础，通过改进子流域划分方法、添加经济社会模块和人工用水模块，对其人工侧支循环模拟进行了系统的完善，开发了基于SWAT的水量-水质-水效联合调控模型SWAT_WAQER。以广西南流江流域为例，从国民经济用水量、河道径流与水质等方面对模型进行校验，并在此基础上划分了2030年“三条红线”控制指标。结果表明：该模型性能良好，能够用于不同节水情景下的国民经济用水量、污染物排放量、水功能区水质达标结果分析，可以作为科学制定“三条红线”控制指标的有力支撑工具。     

Optimization of quinacridone magenta,Cu-phthalocyanine cyan,and arylide yellow ink films formulated for maximum color gamut

Investigation of ink formulation options with the purpose to obtain color-gamut-optimal set of Cyan Magenta and Yellow CMY inks is reported. Implementation of the thickness dependent Kubelka-Munk model on multiple ink layers having different and well-defined thicknesses, provides characteristic absorption and scattering (K, S ) spectra of the ink ingredients. These data enable accurate computation of the reflectance spectrum and thus the L*a*b* color coordinates for any given ink thickness or substrate. Pigment materials investigated are quinacridone as magenta, copper-phthalocyanine as cyan, and arylide yellow. Scaling the peak of the absorption band to the number of molecules per unit area for the specific pigments studied in this article provides the molar extinction coefficients, 1.21 × 10⁴ , 4.7 × 10⁴ , and 3.3 × 10⁴ cm²/millimole respectively, regardless of the different ink formulations used, in accord with Avogadro's principle. Having a set of three pairs of K, S spectra is used to compute the color gamut of any CMY color combination in the L*a*b* space as a function of ink layer thickness and formulation. Using an iterative algorithm, a color-gamut-optimal set of CMY inks is obtained.     

Impact of the anode operating conditions on the liquid water distribution in the cathode gas diffusion layer

Previous experimental results indicate that the humidification conditions at the anode have an impact on the liquid water distribution in the cathode gas diffusion layer. Numerical simulations are developed to reproduce and analyze this effect. Results consistent with the experimental results are first obtained by playing with the partition coefficients of an advanced pore network model computing the liquid water formation and transfer in the cathode gas diffusion layer (GDL) for a large range of operating conditions. Then, a model for the full anode – cathode assembly is developed by combining the pore network model of the cathode GDL and a 1D model describing the heat and water transfer in the various components of the anode-cathode assembly. This enables one to generalize the dry – wet regime diagram introduced in a previous work by incorporating the effect of the humidity condition at the anode.     

APP软件性能效率研究

性能效率是APP软件的重要质量属性，但目前缺乏APP软件性能效率的通用模型。分析了APP软件的性能特征，基于ISO/IEC 25010标准提出了APP软件的性能效率模型，定义了APP软件性能效率的子特性和度量指标。基于提出的APP软件性能效率模型，通过实验对APP软件的性能效率进行了度量及相关分析。     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.