Al2O3基耐磨陶瓷涂层的燃烧合成与应用

介绍了燃烧合成表面涂层技术的基本原理 ,开发了相应的制备工艺 ,并在此基础上研制了内覆陶瓷涂层的复合钢管、弯管及弯头。陶瓷涂层主要由α Al2 O3相、部分FeO·Al2 O3相和 3Al2 O3·2SiO2 相组成 ,采用添加剂可以有效提高熔体的流动性 ,使陶瓷的凝固和结晶过程得到进一步控制 ,有助于减少孔隙 ,提高陶瓷涂层的致密度。现场应用试验表明 ,涂层具有较好的耐磨性能 ,可使设备的使用寿命大为延长     

镁合金表面喷铝防腐蚀层的微观组织分析

在AZ91D镁合金表面热喷铝，用以提高其表面的耐腐蚀性能。采用SEM，EPMA等方法对AZ91D表面喷铝扩散层的组织进行了仔细的观察与分析，发现在防腐蚀层上有大量的Mg17Al12相存在，且呈决状及非连续片状分布。经显微硬度测定，喷铝层硬度较镁合金基体高；腐蚀后这种相凸出于基体，比镁合金基体有较好的耐腐蚀性能。     

The use of natural essential oils as antimicrobial solutions in paper packaging. Part II

We have assessed the antimicrobial, vapor-phase activity of the following natural essential oils (EOs) when used in paraffin-based “active coatings” for paper packaging materials intended to come into contact with foods: clove (Sygzium aromaticum), cinnamon (Cinnamomum zeylanicum), and oregano (Origanum vulgare) EOs, and cinnamaldehyde-enriched cinnamon EO. To our knowledge, this is the first time that such an approach has been presented for consideration by the scientific community.     

Thermal analysis of a ceramic coating diesel engine piston using 3-D finite element method

In this study, firstly, thermal analyses are investigated on a conventional (uncoated) diesel piston, made of aluminum silicon alloy and steel. Secondly, thermal analyses are performed on pistons, coated with MgO-ZrO₂ material by means of using a commercial code, namely ANSYS. Finally, the results of four different pistons are compared with each other. The effects of coatings on the thermal behaviors of the pistons are investigated. It has been shown that the maximum surface temperature of the coated piston with material which has low thermal conductivity is improved approximately 48% for the AlSi alloy and 35% for the steel.     

碳/碳复合材料MoSi2/SiC涂层在动态氧化环境下的性能研究

为了考察MoSi₂/SiC防氧化涂层体系在动态氧化环境下的防护能力,对碳/碳复合材料MoSi₂/SiC涂层试样在1100~1500℃下进行了高温燃气高质流冲刷环境下的氧化试验。结果表明,在1100~1500℃的燃气动态环境下,具有稳定的氧化失重速率,氧化失重曲线近似呈直线关系,氧化失重和氧化失重速率均随着氧化温度的升高而降低,表现出该涂层抗高质流冲刷和氧化的能力随温度的升高而提高,在该温度区间内,随着温度的升高,具有更优异的抗氧化和抗高质流冲刷的能力。     

Corrosion Behavior of a Sputtered K38G Nanocrystalline Coating with a Solid NaCl Deposit in Wet Oxygen at 600 to 700°C

A nanocrystalline coating of K38G alloy was obtained by means of magnetron sputtering. The corrosion behavior of cast K38G alloy and its sputtered nanocrystalline coating with a solid NaCl deposit in dry air or wet oxygen at 600 and 700°C have been studied and compared. The results indicated that the mass gain of the coating is higher than that of the cast alloy at 600 and 700°C. Therefore, nanocrystallization reduced the corrosion resistance at these temperatures. Furthermore, the mass gains of the coating and the cast alloy with a NaCl deposit in wet oxygen were less than that with a NaCl deposit in dry air. The relevant corrosion mechanisms are discussed.     

Oxidation behavior of silicide coating on Ti3SiC2-based ceramic

A silicide coating was prepared on Ti₃SiC₂-based ceramic by pack cementation to improve the oxidation resistance of Ti₃SiC₂, which is a technologically important material for high temperature applications. The microstructure, phase composition and oxidation resistance of the coated sample were investigated. The results demonstrated that the silicide coating was mainly composed of TiSi₂ and SiC. A single layer of a mixture of SiO₂ and TiO₂ was formed on the surface of the coated sample during isothermal oxidation at 1100 °C and 1200 °C for 20h. Compared to Ti₃SiC₂, the parabolic rate constant of silicide coated Ti₃SiC₂ decreased by 2~3 orders of magnitude. Furthermore, the coated sample showed much better cyclic oxidation resistance than Ti₃SiC₂ during the cyclic oxidation at 1100 °C for 400 times. However, during the preparation of the coating, a number of fine cracks formed in the outer layer of the coating. When these cracks penetrated the whole coating during the cyclic oxidation, the oxidation rate was accelerated, which degraded the oxidation resistance. Electronic Publication     

溶胶-凝胶法制备TEOS-DOS基SiO2疏水减反射膜:溶胶微结构对膜性能的影响

以乙醇为溶剂,正硅酸乙酯(TEOS,tetraethoxysilane)在氢氧化铵催化下水解缩聚为纳米尺度的无定型SiO2溶胶颗粒,二甲基二乙氧基硅烷(DDS,dimethyldiethoxysilane)在盐酸催化下水解缩聚为线状聚二甲基硅氧链.用混合溶胶在玻璃基片上旋转镀膜,然后于80℃空气气氛下热处理.实验证明通过DDS将疏水的双甲基链引入镀膜胶体,使膜兼具疏水性和减反射性能.利用激光散射粒度分析仪和电子显微镜研究了溶胶颗粒的粒度变化和聚集情况等溶胶微结构,用物理吸附仪研究了膜的孔结构,考察了热处理前后膜的疏水性和透射谱,得到了溶胶微结构与膜性能之间的关联.     

B4C涂层作为等离子体面对材料的一些性质

介绍了利用等离子喷涂设备,B4C/Cu梯度功能涂层及非梯度涂层的制备技术,在模拟实验装置中测量了在高能粒子(3 keV,D+)的作用下,B4C涂层的化学溅射产额、热解吸性能、热冲击性能及热导率.结果表明B4C是一种有希望为未来聚变装置中等离子体面对的材料.     

表面电沉积合金层提高碳钢齿轮的接触疲劳强度研究

 接触疲劳破坏是齿轮的主要失效形式之一． 在45#钢齿轮齿面电沉积Ni-P-Co合金层，可以显著提高其接触疲劳强度．同时，对合金层的表面形貌，表面粗糙度、显微硬度和疲劳点蚀坑形貌特征等进行了分析．