多重复合地基处理的工程实践

对两种地基处理方法——水泥土搅拌桩与CFG桩在同一场地中的联合应用给予介绍,目的是在不均匀地基加固中找到一种合理的加固方法,使加固后的地基满足设计及使用要求。     

水泥搅拌桩在基坑工程中的应用与改进

本文结合泉州地区工程地质情况及水泥搅拌桩的应用情况,在设计计算方面进行了一些探讨,同时提出了设计上的改进措施。     

深层搅拌法的工程实践

本文提出了深层搅拌法地基加固的设计计算方法。并概要介绍了为不同的加固目的，在各种土质条件下应用深层搅拌法作为地基加固方案的典型工程实例，如：在工业设备基础下、厂房内大面积堆载下、多层建筑的条形基础和独立柱基础下以及飞机场联络道下的深厚层淤泥质土的加固；用水泥土连续墙作深基坑边坡支护方法等。     

深厚软土大型油罐搅拌桩复合地基试验研究

本文结合国家石油储运舟山岙山基地成品油罐区4个10000m3油罐的实践，对采用搅拌桩复合地基加固深厚软土建大型油罐问题进行试验研究，简单介绍了设计方法和实施情况，对室内试验和现场测试结果进行了详细分析，提出了一些有价值的结论。     

加芯搅拌桩破坏模式的分析

结合加芯搅拌桩的成桩特点，通过原位试验的研究，对加芯搅拌桩的几种破坏模式进行了研究、分析，可供工程设计参考，从而使工程既安全又经济。     

The effect of micro-alloying addition of Cr on age hardening of an Mg–Zn alloy

This work reports a chemical method called “co-deposition route” for fabricating ND (nanodiamond)/Cu composite at a molecular-level mixing. The main procedure of “co-deposition route” includes four steps. ND particles have been functionalized by HF acid before co-deposition. SEM, HRTEM (high-resolution transmission electron spectroscopy), XRD (X-ray diffraction), EDS (energy-dispersive spectrum analysis) and optical microscope were carried out to characterize the as-prepared composite powders and bulk composites. Results indicated that copper matrix composite with a homogeneous dispersion of functionalized ND particles can be prepared. The modification of ND particles was performed by HF (30 vol%) acid at 70 °C, and CF bond was successfully detected by XPS (X-ray photoelectron spectrum) and IR (Infrared spectroscopy). The properties of relative density, microhardness and electric conductivity of ND/Cu composites have been measured. With the comparison of conventional methods, it showed that the as-prepared ND/Cu composites with good combined performances have a promising future for industry application.     

混沌挤出过程相空间动力学行为分析与表征

根据对称性与周期性,建立了混沌螺杆螺槽的混合过程动力学模型。采用有限体积方法,得到一个周期长度速度场数值解,将结果映射到3个周期长度的相空间内对混沌混合过程动力学进行分析与表征。结果表明,常规的层流混合和混沌混合区域共存,两种混合区域通过"8"字型同宿轨道包围的KAM岛分割开来,内部为常规混合区域,外围为混沌混合区域。示踪粒子在三维重构的相空间内动力学行为清楚地刻画了系统向混沌进发的过程及速度。另外,由于长度有限,混沌混合的作用受到限制,不再具有无穷的自相似结构,可以采用KAM岛的区域大小来表征混合。     

粉体混合均匀性定量评估模型的建立与研究

针对粉体混合均匀性难以快速准确检测和定量化描述的问题,通过大量实验采用分形理论建立了粉体混合均匀度定量评估模型,即数出不同半径圆内包含的粉体颗粒数,在双对数坐标上找出"数目-半径"或"数目-质量"点,与理论计算的标准线比较来说明粉体混合的均匀程度。当不同粒径的粉体混合,用"数目-半径"分析法;同粒径的粉体混合,用"数目-质量"分析法。同时提出了定量评估粉体混合的不均匀程度,特别适合于现场检验。     

安钢烧结二次料场工艺设备改造

介绍了安钢烧结厂混匀供料系统提高设备能力的做法,通过技术改造使混匀料场的能力由50%提高到71%,混匀料年产量增加了267万t,保证了烧结混匀料的供应。     

Fluid Flow and Mixing in Non-Isothermal Water Model of Continuous Casting Tundish

Fluid flow and mixing of molten steel in a twin-slab-strand continuous casting tundish were investigated using a mixing model under non-isothermal conditions.This model led to a set of ordinary differential equations that were solved with a Runge-Kutta algorithm.Steady state water modeling was carried out under non-isothermal conditions.Experimental data obtained from the water model were used to calibrate the mixing model.Owing to the presence of a mixed convection in the non-isothermal conditions,a channelizing flow would be created in the fluid inside the tundish.A mixing model was designed that was capable of predicting RTD（residence time distribution）curves for different cases in non-isothermal conditions.The relationship between RTD parameters and the Tu（tundish Richardson number）was obtained for various cases under non-isothermal conditions.The results show that the RTD parameters were completely different under isothermal and non-isothermal conditions.The comparison of the RTD curves between the isothermal and non-isothermal conditions presents that the extent of mixing in the tundish in non-isothermal conditions is lower than the mixing extent in isothermal conditions.