我国纳米科技的现状与展望

本文概述了纳米科技的沿革，及其在国内外发展的情况，并就我国如何进一步发展纳米科技提出了自己的想法。     

中原边际小断块油田油气集输工艺配套技术探索

介绍了中原边际小断块油田开发建设以来几种油气集输工艺配套技术的成功应用，并从节能降耗、工艺合理匹配、提高系统效率等方面阐述了其他适于边际小断块油田油气集输工艺的配套技术。     

煤基链篦机-回转窑一步法直接还原设备改造及技术操作要点

本文主要论述了煤基链篦机-回转窑一步法直接还原关键设备改造及有关技术操作要点，并提出了进一步提高产量，稳定操作，延长作业周期，降低生产成本的技术改造方案。     

唐钢ER70S-6焊丝钢的生产工艺研究及质量分析

介绍了唐钢ER70S-6焊丝钢的特点，对盘条质量进行了分析。对该钢化学成分、冶炼和轧制工艺进行了优化研究，使其综合性能明显改善。     

无铬钝化技术研究的进展

评述了文献报道和各种不同的无铬钝化工艺的特点及其发展现状。目前还没有一种无铬钝化工艺能够完全代替铬酸盐钝化工艺，某些无铬钝化工艺在某些方面已经与铬酸盐钝化相当，但其市场前景、应用范围及用户环保效果还需要进一步研究。     

分形图像压缩的信源信道联合编码

本文针对分形图像压缩编码后所得各部分压缩数据的特点，分析了分形图像压缩各部分数据在传输中对传输信道干扰的敏感程度，并根据各部分数据对信道干扰的敏感程度的不同，提出了一种分形图像压缩的信源信道联合编码方法。仿真结果表明，采用所提出的分形图像压缩的信源信道联合编码方法后，分形图像压缩数据对传输信道的敏感程度降低，图像质量有较大提高。     

Micromechanical modelling of ductile crack growth in the binder phase of WC–Co

This study focuses on numerical simulation of ductile failure in the Co binder phase of WC–Co hardmetal. The growth of edge cracks under mode I loading is considered. A computational micromechanics approach is taken where the Co binder ligaments are explicitly represented in finite element models. An embedding technique is employed. Crystal plasticity theory is used to represent plastic deformation in the Co ligaments. Crack propagation in the binder is simulated using an element removal technique based on a modified Rice and Tracey model for ductile void growth, and fracture resistance curves are generated. Parameter studies are performed for variations in microstructrual parameters such as numbers of Co ligaments ahead of the crack tip and local Co volume fraction. The importance of thermal residual stresses and finite element mesh density are also investigated.     

First Harmonic (2f) Characterisation of Resonant Frequency and Q-Factor of Micromechanical Transducers

In this paper, the response to the first harmonic component (2f) of the electrostatic force in single terminal driven electrostatic comb-drive and parallel-plate drive was used as a signal to extract device parameters, namely, the Q-factor and resonant frequency instead of the fundamental (1f) resonance response. It is shown that the difficulty in motional measurement due to electrical cross-talk (parasitics) using 1f measurement can be overcome with a higher signal-to-noise ratio of the 2f signal. Both atmospheric (low-Q) and reduced pressure environment were investigated using off-chip electronics and lock-in amplifier. The measurements were done on the electrostatic comb-drive and capacitive parallel plate sensing plates that form the two core modules of a yaw rate sensor (dual-axis resonator). The effects of AC and DC bias voltages on the measured response have been investigated. Experimental amplitude and phase response data have been analysed using the Lorentzian curve-fit, Resonance Curve Area (RCA) method, the half-power bandwidth method (3 dB) and the Nyquist plot for data fitting and determination of the Q-factor and resonance frequency.     

复合载荷下波纹管横向非线性弯曲摄动有限元法

采用新的小参数、将摄动法和有限元法相结合,研究了复合载荷作用下波纹管横向非线性弯曲的位移和应力分布。小参数为结构环向应变的均方根。将节点位移摄动展开,并以复合载荷的等效节点载荷为参考载荷,将其公共系数1摄动展开。由此划分载荷的级别、建立各级载荷和相应位移的关系,避免了常规的迭代运算。算例为一考虑自重的U型波纹管在注满水时的横向非线性弯曲问题。计算表明,波纹管的挠度和膜应力有非常显著的非线性效应;当最大挠度与壁厚之比达到5.1后本法将失效。本法在摄动小参数的选取和复合载荷的处理上有特色,能解决较大的挠度问题。     

云南东川泥石流沟与非泥石流沟~(137)Cs示踪法物源研究

运用1 37Cs示踪法调查云南东川小江流域 6条泥石流沟、6条非泥石流沟和主河的泥沙来源。泥沙主要来源于冲沟侵蚀和滑坡崩塌堆积、坡耕地和草地。坡耕地和草地表层土壤1 37Cs平均含量分别为 0 9Bq m2 和1 98Bq m2 ,冲沟沟壁和滑坡崩塌堆积土体1 37Cs。作者通过 3种源地土体1 37Cs含量的比较 ,分析了细粒泥沙(<0 0 1mm)的来源。 6条泥石流沟冲沟侵蚀和重力侵蚀 (滑坡崩塌 )的相对产沙量变化于 90 2 %～ 1 0 0 % ,平均值为 95 1 % ,6条非泥石流沟的相对产沙量变化于 74 5 %～ 83 3% ,平均值为 78 9%。小江主河为 81 4 %。