便携式全站仪在钻采井架钢结构安装中的应用

文章介绍了一种由便携机和全站仪组成的便携式全站仪 ,阐述了该全站仪在钻采井架钢结构施工安装过程中的测量工作 ,对测点产生的误差采用伪逆自由网平差方法进行处理 ,控制点的精度可达到± 5mm ,该全站仪具有快速、灵活、准确的特点 ,不仅提高了生产效率 ,而且达到了对资料的计算机化管理。     

技术攻关提高成材率

介绍了广钢集团高速线材生产线的生产和工艺概况，分析了成材率的影响因素，阐述了技术攻关提高成材率所采取的措施和取得的良好效果及经济效益。     

250W带功率因数校正整流电源模块的研制

功率因数校正技术越来越成为电源行业研究的热点。文中介绍了适用于雷达等设备的250W带功率因数校正整流电源模块的设计，分析了其中升压电感器设计、主开关管保护、控制电路消振、散热设计和表面贴装等关键技术，完成了实验研究，获得了满意的试验结果。     

基于复数主成分分析的磁共振波谱信号衰减系数的自动校正

衰减系数的校正是磁共振波谱信号处理和分析过程中的一个关键难题。本文基于复数主成分分析，提出了一种自动的磁共振波谱衰减系数的校正方法，较成功地解决了这个难点问题。文中的模拟数据及其实现结果充分验证了该方法的有效性。     

Investigation on vapor-cooled current leads operating in a pulse mode

This paper describes transient numerical modeling for thermal characteristic of vapor-cooled current leads under pulse operation. The transient thermal analysis considers the temperature difference between a helium gas flow and a copper lead with temperature dependent properties of helium gas, copper and stainless steel. The numerical analysis was validated by an experiment with commercially available 100 A vapor-cooled current leads. A proper overloading factor calculation and the effect of intermediate cooling are presented for the current leads under pulse operation, which can significantly reduce heat input to a cryostat.     

裂缝性油气藏采收率：100个裂缝性油气田实例的经验总结

通过对世界上100个裂缝性油气藏的综合评价，研究储集层及流体本身的性质(包括孔隙度、渗透率、黏度、可动油比例、含水饱和度、润湿性及裂缝分布特征等)和驱动机制及油藏管理战略(优化日产量和采用不同类型的提高采收率技术)对其最终采收率的影响。将裂缝性油气藏分为4类：I类的基质几乎没有孔隙度和渗透率，裂缝是储存空间和流体流动的通道；Ⅱ类的基质有较低的孔隙度和渗透率，基质提供储存空间，裂缝提供流动通道；Ⅲ类(微孔隙)的基质具有高孔隙度和低渗透率，基质提供储存空间，裂缝提供流动通道；Ⅳ类(大孔隙)的基质具有高的孔隙度和渗透率，基质提供储存空间和流动通道，裂缝仅增加渗透率。对26个Ⅱ类油气藏和20个Ⅲ类油气藏的开采历史的研究表明：Ⅱ类油气藏的采收率受水驱强度和最优日产量控制，日产量过高会很容易破坏Ⅱ类油气藏，一些Ⅱ类油气藏如果管理得当，采收率可以很高，不需要二次或三次采油；Ⅲ类油气藏的采收率主要受岩石和流体本身性质的影响，特别是基质渗透率、流体重度、润湿性以及裂缝强度等，不进行二次或三次采油不可能完全开采，往往需要采用一些提高采收率的专门技术。以往将Ⅱ类和Ⅲ类裂缝性油气藏归为一类，认识它们的区别将有助于选择更好的开发策略。     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

就地补偿在动力厂水泵电机上的应用实例

就我公司动力厂给水车间155kW水泵电机无功就地补偿的可行性及经济效益进行了分析和研究，对工厂用电如何节能降耗有一定的参考价值。     

Significance of the elastic peak stress evaluated by FE analyses at the point of singularity of sharp V-notched components

The paper presents an expression useful to estimate the notch stress intensity factor (NSIF) from finite element analyses carried out by using a mesh pattern with a constant element size. The evaluation of the NSIF from a numerical analysis of the local stress field usually requires very refined meshes and then large computational effort. The usefulness of the presented expression is that (i) only the elastic peak stress numerically evaluated at the V‐notch tip is needed and no longer the whole stress–distance set of data; (ii) the adopted meshes are rather coarse if compared to those necessary for the evaluation of the whole local stress field. The proposed expression needs the evaluation of a virtual V‐notch tip radius, i.e. the radius which would produce the same elastic peak stress than that calculated by FEM at the sharp V‐notch tip by means of a given mesh pattern. Once such a radius has been theoretically determined for a given geometry, the expression can be applied in a wide range of notch depths and opening angles.     

高炉与风机配置的优化

根据高炉风机配置的具体情况 ,为充分发挥大风机生产优势 ,建立了适宜的送风制度及装料制度 ,对利旧风机采取了自动防喘振控制、高压水阻软启动的措施 ,风机仪表采用集散控制 ,并优化上料系统 ,提高了高炉上料能力。一系列优化方案保证了高炉稳定、安全、顺行 ,1号、2号高炉利用系数分别由 3 .3 64、3 .43 2t/m3.d提高到 3 .917和 3 .767t/m3.d。