PVC四通管注射模设计

介绍了PVC四通管注射模设计 ,阐述了弯型芯的旋转抽芯过程以及模具顶出、回程及冷却系统设计。实践证明 ,该模具结构合理 ,生产的塑件可以满足设计要求     

电传动装甲车辆冷却系统水路性能试验研究

根据电传动装甲车辆冷却系统高低温双泵双循环设计要求,通过台架联机试验全面测试了冷却系统双循环水路及各循环支路温度变化和水流量分配特性、发电机绕阻温度变化规律及低温循环水路工作性能,测试结果表明:发电机冷却水路与发动机循环水路串联可行,双循环水路及各循环支路水流量和进出口温度变化满足动力系统不同工作状态散热要求,所选部件匹配合理,达到设计要求.     

蒸发式冷凝在制冷工艺上的应用

分析对比制冷工艺中几种冷凝方式，指出发展蒸发式冷凝技术对制冷系统节能的重要意义；通过分析蒸发式冷凝的换热机理，在试验和实践的基础上讨论了影响蒸发式冷凝器性能的几个重要因素。     

Z900MCM综述

介绍了Z900 MCM设计和布局,可控塌陷芯片连接(C4)工艺在Z900 MCM组装中的应用。从设计上通过加入垂直电感器及去耦电容器减小其噪声。通过基板测试和功能测试,剔除有缺陷的基板和芯片。Z900 MCM采用先进的MCM—D技术和MCM返工及冷却技术。Z900 MCM平均无故障时间高达40年。     

灯泡贯流式机组发电机冷却装置技术改造方式的探讨

灯泡贯流式发电机组直径小,转速低,发电机的通风冷却是一个难点。通过对京南、马骝滩、石面坦及南津渡等水电站的发电机运行过程中出现的温升过高,定子线棒绝缘受损等问题的分析,提出了解决的措施与改进方案,并对灯泡贯流式机组冷却系统的设计提出了建议,可供参考和借鉴。     

剂量率对聚四氟乙烯辐射裂解的影响

本文研究了在以电子加速器的电子射线为辐射源时,剂量率对PTFE辐射裂解的影响。在剂量相同的条件下,剂量率从1.44×10~4 rad/s增至5.75×10~4 rad/s,裂解效率提高3.3倍。剂量率和各断裂参数(单位剂量裂解度a_0,G(s)值等)均成线性关系。当裂解度一定时,剂量率与剂量成反变关系。     

Computer modeling of the continuous annealing furnace

A computer program to calculate the strip temperature heated in the continuous annealing furnace was developed, using the zone method for radiative heat transfer analysis with the measured gas temperature in the furnace. Using theF _E Operator, the present study considered the effects of soot and transient species, in addition to the H₂O−CO₂ gas mixture on the gas radiative heat transfer. The predicted strip temperature distribution forF _E=1.05 represented well the measured data. The maximum difference in the heat flux transfered to the strip from the combustion gas forF _E=1.0 (without soot and transient species gas radiation) and 1.05 (with soot and transient species gas radiation) was about 15%. The present study also investigated the effects of line speed and thickness variations on the strip temperature, establishing the bases for the on-line computer model.     

Partitioning multiple objective optimal solutions with applications in radiotherapy design

The optimal partition for linear programming is induced by any strictly complementary solution, and this partition is important because it characterizes the optimal set. However, constructing a strictly complementary solution in the presence of degeneracy was not practical until interior point algorithms became viable alternatives to the simplex algorithm. We develop analogs of the optimal partition for linear programming in the case of multiple objectives and show that these new partitions provide insight into the optimal set (both pareto optimality and lexicographic ordering are considered). Techniques to produce these optimal partitions are provided, and examples from the design of radiotherapy plans show that these new partitions are useful. A. Holder. Research conducted at Trinity University, TX, and The University of Mississippi, MS. This research was partially supported by ONR Grant N00014-01-1-0917.     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.     

低温液体冷却循环器的研究与开发

根据低温生物、生化实验研究和产品小试时应用低温条件的特点，提出机械制冷的冷却循环器，讨论了工作原理和制冷量计算，对其制冷系统和温度控制进行介绍。