Differences between oculomotor and perceptual artifacts for temporally limited head mounted displays

We used perceptual and oculomotor measures to understand the negative impacts of low (phantom array) and high (motion blur) duty cycles with a high‐speed, AR‐likehead‐mounted display prototype. We observed large intersubject variability for the detection of phantom array artifacts but a highly consistent and systematic effect on saccadic eye movement targeting during low duty cycle presentations. This adverse effect on saccade endpoints was also related to an increased error rate in a perceptual discrimination task, showing a direct effect of display duty cycle on the perceptual quality. For high duty cycles, the probability of detecting motion blur increased during head movements, and this effect was elevated at lower refresh rates. We did not find an impact of the temporal display characteristics on compensatory eye movements during head motion (e.g., VOR). Together, our results allow us to quantify the tradeoff of different negative spatiotemporal impacts of user movements and make subsequent recommendations for optimized temporal HMD parameters.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

Broadband bowtie belt nanoantennas

In this article, we study a linear array of bowtie nanoantennas placed between two metallic strips that can work from 800 to 1420 nm (600 nm linewidth), with an electric field enhancement factor close to 20. We study the dynamical change of the position of the electric field enhancement amongst different elements in the array and, at the same time, the effects of dispersion on the scalability of the array elements. A systematic analysis and methodology to produce an array that can operate over a large bandwidth whilst maintaining the electric field enhancement without significant variation is provided.     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

Behaviour of Surface Defects in Wire Rod Rolling

Defects are often present in rolled products, such as wire rod. The market demand for wire rod without any defects has increased. In the final wire rod products, defects originating from steel making, casting, pre‐rolling of billets and during wire rod rolling can appear. In this work, artificial V‐shaped longitudinal surface cracks have been analysed experimentally and by means of FEM. The results indicate that the experiments and FEM calculations show the same tendency except in two cases, where instability due to fairly “round” false round bars disturbed the experiment. FE studies in combination with practical experiments are necessary in order to understand the behaviour of the material flows in the groove and to explain whether the crack will open up as a V‐shape or if it will be closed as an I‐shape.     

Optoelectronic Method of Noncontacting Reconstruction of the Profile of a Surface of Three Dimensional Objects of Large Dimensions

An optoelectronic method is considered for noncontacting reconstruction of the surface profile of three-dimensional objects of large dimensions. The optimal conditions for performing measurements are identified. It is shown that the proposed method, in contrast to the already known methods, does not require fine tuning of the equipment. A numerical method is given for compensating distortions caused by aberrations. A method is described for reconstructing the surface profile cell by cell which increases the accuracy of measurements.     

平面阵列波导光栅波导模式参量的分析

用周期波导的方法分析平面阵列波导光栅(AWG)的本征方程及波导模式参数,结果表明波导传播常数是带状分布的,与波导间隔有关。分析结果对器件的优化设计有一定的指导意义。     

数字化正弦平方脉冲信号

依据正弦平方脉冲的数学方程及其频谱分布，分别导出了与理想和标称视频带宽相对应的正弦平方脉冲的数学表达式及其编程生成方法。实验表明，此法不仅精确，而且便于修改参数，并可直接读人数字电视系统，来测定视频线性响应。     

对理想弯曲街道进行场强预测的方法

提出了一种新的射线跟踪接收判断技术,它是已有的两类射线跟踪技术的结合,能够解决曲面反射的问题。这种新技术能够在任意形状建筑物组成的复杂环境中进行场强预测。而且此种方法可以自由的改变接收球的半径,以满足精度的需要。